Clearaudio concept Signature User manual

© clearaudio electronic GmbH Made in Germany
Loving music
clearaudio
User manual
Bedienungsanleitung
Pic. similar /
Abb. ähnlich
Signature
concept

User manual / Bedienungsanleitung
Page / Seite 2 © clearaudio electronic GmbH
User manual .....................................................2 - 16
Bedienungsanleitung .......................................17 - 31
Dear Clearaudio customer,
the concept already caused a sensation when it was launched on the market in 2009.
As an entry-level package with a specially developed tonearm and cartridge, a revolutionary sound
package with an undisputed price, design and performance range was created and enjoys worldwide
fame with over 20.000 units sold.
After more than 10 years of consistency, the concept gets an update and becomes concept Signature.
The new control technology with integrated self-calibration, new setting options and additional
Tacho Speed Control (“TSC”) achieve even better measured values in synchronization, wow and
utter and impulse stability.
The new design of the surface - now with sensor switch - also combines variable setting options and
functions, while at the same time the new encoder also serves as the basis for further generations
and expansion stages. In addition, there is also the improved motor suspension using several O-rings
(“ISM”), which completely decouple the motor from the chassis and were adopted in a simplied
form from the Reference Jubilee.
The concept Signature is another milestone and the result of our consistent research and constant
development of our products.
Please read the instruction manual for easy setup and to discover how to care for your
concept
Signature turntable to enjoy music for many years. Follow the instructions carefully to avoid any
potential damage. Not following our instructions could void your warranty.
We wish you a great musical experience with your new Clearaudio concept Signature turntable.
Clearaudio electronic GmbH

User manual / Bedienungsanleitung
Made in Germany Page / Seite 3
Loving music
You can nd these and many other accessories in the Clearaudio online shop
(www.analogshop.de) or through your Clearaudio dealer.
Matching accessories from Clearaudio:
Dustcover for concept Signature turntable
(Art. No AC168)
concept clamp
(Art. No. AC122)
Replacement belt for
concept series turntable
(Art. No. AC123)
Professional Power 12V transformer power supply
(Art. No. EL039/S)
Also available in black.
smart power 12V battery power supply
(Art. No. EL035/B/S)
Also available in all black nish.

User manual / Bedienungsanleitung
Page / Seite 4 © clearaudio electronic GmbH
Safety instructions
1. General information
Check the turntable for any damage before using it. Do not connect the turntable if damaged!
Never connect the turntable if it has been dropped or gotten wet, contact your dealer to have the turntable checked.
Never expose the turntable to rain or moisture.
Never touch the power cord of the device with wet hands.
Regular visual inspections for defective insulation on the connection cable are also recommended for your own safety.
A damaged cable should be replaced immediately by a specialist!
Never pull on the power cord to unplug the device. Always pull directly on the plug!
The inside of the turntable is maintenance free. Never open the case or attempt to repair the unit yourself, since this
can lead to loss of warranty!
We recommend disconnecting the power supply from the mains if you do not operate the device for a longer period of
time.
The turntable does not feature an automatic shut-o mechanism.
Therefore, as soon as the stylus has reached the run-out groove, engage the tonearm lift and switch the turntable o.
Not suitable for children! Scope of delivery may contain small parts that can be swallowed.
2. Intended use
The
concept Signature is a turntable for playing records.
The intended use of the concept Signature in accordance with the information provided in the user manual only.
The power supply may only be operated with maximum permissible connection values according to the technical data.
Any other use or modication of this product is not intended.
3. Location of installation
Avoid locations with direct sunlight, temperature uctuations and high humidity.
Likewise, avoid placing electronic devices near heaters, heat lamps, or other devices that produce heat.
The device is designed for operation at room temperature.
No objects with an open ame may be placed on or near the device (burning candles or similar).
4. Overload
The product is designed to comply with all necessary safety regulations. However, you should not leave the device
unattended under extreme loads.
5. Maintenance
Never use aggressive cleaning detergent.
Donotusedryclothsforcleaningasthisgeneratesstaticelectricity.SuitablecleaningandcareproductsfromClearaudio
are available from www.analogshop.de or from specialist retailers.
The bearing of the turntable platter can be lubricated every 2 years with the oil provided.
Put 1 or 2 drops of the oil into the bearing for lubrication.

User manual / Bedienungsanleitung
Made in Germany Page / Seite 5
Loving music
6. Health information
Permanently high volume can lead to various types of hearing damage. Use high volume responsibly!
7. Service
The concept Signature turntable should be repaired during the guarantee period by the manufacturer or authorized
dealer only, otherwise the warranty claim expires. All Clearaudio products should only be serviced by specialist retailers.
If, despite the high production standard, a service is necessary, the concept Signature turntable must be send to
Clearaudio through your dealer.
8. Transport
Use the original packing material for further transportation of the concept Signature turntable, otherwise serious damage
could occur.
Be sure to pack the device exactly as it was shipped.
Safe transport is only guaranteed in the original packaging.
Proceed in reverse as described for assembly when packing.
Always remove the turntable platter and replace the foam securing the sub-platter as well as the tape securing the
tonearm and the cartridge stylus protection. Otherwise serious damage can occur.
Please also ensure that you fully retract the turntable feet.
For any transportation of the concept Signature turntable, please ensure that the platter is packed with the upper
surface facing downwards into the packaging.
Clearaudio assumes no liability for any damage that may occur due to incorrect packing.
9. Disposal
Do not dispose this product together with other waste.
WEEE Reg. No.: DE26004446
10. CE Marking
This electronic product corresponds to the applicable guidelines for obtaining the CE mark.


User manual / Bedienungsanleitung
Page / Seite 6 © clearaudio electronic GmbH
Contents
1. Packaging overview...............................................................7
2. List of component..................................................................7
3. Set-up ...................................................................................8 - 10
4. Initial operation and calibration of speed ............................11
5. Important notes ....................................................................12 - 13
6. Troubleshooting.....................................................................14 - 15
7. Technical data........................................................................16
Warranty information................................................................32 - 33

User manual / Bedienungsanleitung
Made in Germany Page / Seite 7
Loving music
1. Packaging overview
The Clearaudio concept Signature turntable is delivered in a customized packing to ensure its safe
transport.
Please retain the original packaging for any future transportation and shipping.
Please see the list below to check the contents of your Clearaudio concept Signature turntable.
2. List of components
1) Turntable chassis with tonearm, cartridge and drive belt on sub-platter.
2) Turntable platter.
3) Accessories:
Level gauge, smart stylus force gauge, hex wrench (size 2 / 2.5), power supply incl. adapter,
user manual, Clearaudio return delivery note, warranty card.
First layer:
concept Signature turntable chassis
including integrated motor unit and
tonearm with cartridge.
Second layer:
Turntable platter,
accessories box,
user manual,
Clearaudio return delivery note,
warranty card
Pic. 1: Packaging overview

User manual / Bedienungsanleitung
Page / Seite 8 © clearaudio electronic GmbH
3. Set-up
Setting up the concept Signature turntable is easy. The turntable chassis, tonearm and cartridge are
already assembled and all key parameters have been pre-adjusted and tested at the Clearaudio
factory.
The
concept Signature turntable needs a set-up space of at least 17 x 14 inches.
3.1
First take the
concept Signature turntable chassis out
of the package and place it on a suitable surface.
Then remove the drive belt from the plastic bag.
3.2
Place the drive belt around the sub-platter and
around the motor pulley and the tacho meter.
Pic. 2: Placing the turntable
Pic. 3: Mounting the drive belt

User manual / Bedienungsanleitung
Made in Germany Page / Seite 9
Loving music
Pic. 4: Placing the platter
Pic. 5: Removing the adhesive security tape
3.3
Take the platter out of the package and carefully
place it with both hands onto the shaft.
Make sure that the hollowed side faces down towards
the sub-platter.
3.4
Carefully remove the adhesive security tape and
other security materials from the tonearm and the
cartridge.
3.5
Please level the turntable using the level gauge
provided.
All key parameters have been adjusted at the
Clearaudio factory.
Pic. 6: Levelling the turntable

User manual / Bedienungsanleitung
Page / Seite 10 © clearaudio electronic GmbH
Lock screw
3.6
If the bubble of the level gauge is not centered
within the black circle, please turn the turntables
feet clockwise or anti-clockwise until you reach the
perfectly leveled position.
You will only get the best sound from your
concept
Signature
turntable if it is perfectly leveled.
3.7
Connect one end of the external power supply
provided to the socket on the rear of the
concept
Signature turntable and the other end to a live AC
outlet.
Then connect the tonearm cable to your phonostage
(red plug = right channel, black plug = left channel).
Finally, connect the grounding and switch on the
device on the back using the “On/O” switch.
Your concept Signature turntable is now completely
assembled and ready to play.
Pic. 7: Adjustment of the turntable feet
Pic. 8: Power supply of the turntable
Clearaudio is wishing you a lot of pleasure with your new concept Signature turntable.

User manual / Bedienungsanleitung
Made in Germany Page / Seite 11
Loving music
Pic. 10: Calibration of the concept Signature
4. Initial operation and calibration of speed
4.1 Initial operation
If the concept Signature is in standby, press the
button once to put the drive into operation at the
basic speed of 33 1/3 rpm.
Press again to change the speed to 45 rpm.
Another press puts the drive back into standby mode.
We recommend to let the turntable run in for around
15-30 minutes when using it for the rst time.
4.2 Calibration of speeds
Thanks to the newly developed motor control, the concept Signature calibrates itself to always
maintain the perfect speed.
However, manual calibration is possible. This is particularly recommended if the turntable has not
been in use for a long time, wearing parts (e.g. belts) have been replaced or the drive is being
repositioned after moving, for example.
If you would like to start the calibration manually, please proceed as follows to recalibrate both
speeds. This process can take up to 10 minutes.
The turntable have to be in standby mode to start
the calibration. On the back of the turntable you
will nd the calibration button next to the “On/O”
switch.
Since this is recessed in the chassis, you need a
narrow screwdriver or alternatively a ballpoint pen
or something similar to press the button.
Hold this down for approx. 5 seconds. As the
turntable calibrates itself, the platter rotates and
the display quickly changes between 33 (=33 1/3)
and 45.
After calibration is complete, the turntable stops and switches to standby mode by itself.
Pic. 9: Control unit of the concept Signature

User manual / Bedienungsanleitung
Page / Seite 12 © clearaudio electronic GmbH
5. Important notes
5.1 Adjustment of the tracking force
The tracking force is already preset at the factory.
Please always remove the record from the turntable if you want to check or adjust the tracking
force. To check the values, we recommend using the delivered smart stylus force gauge or the
Clearaudio Weight Watcher touch (Art. No. AC 163).
The recommended tracking force for the Clearaudio concept MM cartridge is 2.2g (± 0.3g) and for
the Clearaudio concept mc cartridge is 2.2g (± 0.2g).
Pic. 11: Using the smart stylus gauge
✓

Tracking force too high!

Tracking force too low!
This position of the needle corresponds
to a tracking force of 20mN (2.0g).
Abb. 12: Einstellen des Auagegewichts
To adjust the tracking force, the counterweight at the
end of the tonearm must be turned.
Attention: Please hold the tonearm rmly on the
tonearm tube while turning the counterweight to avoid
damage!
Red arrow (shift towards tonearm end)
= less tracking force -> turn counterweight
counterclockwise (left)
Green arrow (shift towards the start of the
tonearm)
= more tracking force -> turn counterweight
clockwise (right)
Set the correct tracking force of your pickup according to the manufacturer‘s instructions.

User manual / Bedienungsanleitung
Made in Germany Page / Seite 13
Loving music
5.3 Adjustment of the anti-skating force
Again, since everything on the turntable is pre-
assembled and tested, including tonearm and
cartridge, there is usually no need to change any of
the concept Signature turntable parameters.
If you still want to change the anti-skating, please
contact your dealer, who has the necessary
accessories, e.g. test record, measuring tool.
Your specialist dealer will nd the anti-skating screw
on the underside of the concept Signature turntable.
Clearaudio assumes no liability for incorrect handling or any damage caused if non-qualied
persons attempt the above adjustments.
Pic. 14: Adjustment of the anti-skating
5.2 Adjustment of the tonearm height
Since everything on the turntable is pre-assembled
and tested, including tonearm and cartridge, there
is usually no need to change any parameters on the
concept Signature turntable. If you wish to change
the height of your tonearm, please refer to your
nearest qualied dealer or service personnel.
Your dealer can make the height adjustment by
loosening the locking screw on the side of the
tonearm base of your turntable.
Please note that the basic setting is made without
an additional mat on the plate.
Clearaudio assumes no liability for incorrect handling or any damage caused if non-qualied
persons attempt these adjustments.
Pic. 13: Adjustment of the tonearm height

User manual / Bedienungsanleitung
Page / Seite 14 © clearaudio electronic GmbH
6. Troubleshooting
If you have a problem with your concept Signature turntable, rst check the possible causes to rule
out incorrect operation.
If the error persists, please contact your dealer!
Never try to open the device and/or repair it yourself, this will void the warranty!
Error Cause Measure
Device does not
work Is the power cord plugged in? Check the connection.
Is the power switch in the correct
position? Check the switch on the back of the device.
No sound
The tonearm and phono stage
are not properly connected. Check the cable connection between the tonearm and the phono stage.
Is the amp turned on? Check the power supply to the amplier.
The volume on the amplier/
loudspeaker is set too low or on
„mute“.
Check the volume settings.
Is the cartridge protective cap
still attached? Remove the cartridge‘s protective cap.
Is the tonearm in the raised
position? Lower the tonearm into the lead-in groove.
Is the stylus damaged? Check the stylus and have the cartridge checked
by a specialist if necessary.
Bad sound /
noise
Is the record or the stylus dirty or
damaged? Clean the record / or the cartridge. Clearaudio oers many helpful accessories for care and
cleaning. In the event of damage, we recommend
an assessment by a specialist and if necessary, an
exchange.
Is the cartridge properly mounted
into the tonearm? Check the installation using the relevant user manual and correct them if necessary.
Has the tracking force been set
too high or too low? Adjust the tracking force.
Is the correct operating mode
(MM / MC) set on the amplier? Check the settings of your phono stage.
The pre/amp does not have
enough gain. Check the settings of your phono stage.
Pre/amp is mismatched. Swap the plugs of the turntable that are connected
to the left and right outputs.

User manual / Bedienungsanleitung
Made in Germany Page / Seite 15
Loving music
Needle bounces
or slides across
record
Is the record or the stylus dirty
or damaged? Clean the record / or the cartridge. Clearaudio oers many helpful accessories for care and
cleaning. In the event of damage, we recommend
an assessment by a specialist and, if necessary,
an exchange.
Has the tracking force been set
too high or too low? Adjust the tracking force.
Is the record deformed or
scratched? Use a record clamp or replace the record.
Is the turntable leveled? Check the alignment of the turntable and adjust
if necessary.
Is the antiskating set too high/
low? Contact your dealer to have the setting checked and corrected if necessary.
Platter does not
turn
Is the drive belt properly
attached? Check the position of the drive belt.
Is the power cord connected
properly? Check the connection.
Is the power switch in the
correct position? Check the switch on the back of the device.
The turntable is still in standby
mode. Activate the drive by pressing the button.
Noisy sound
Is the drive belt properly
attached? Check the position of the drive belt. Is it too loose and needs to be changed? Please
note: After changing the belt, we recommend
recalibrating the turntable.
Humming noises
Contact problems with the signal
connections (e.g. cinch plugs,
adapters for extensions)
Check all connections; reduce the level on the
(pre-)amplier to a low volume for acoustic
checking of gross errors.
Thepickup pinsaremixedup,not
connected correctly or defective. Check the pin assignment of the pickup.
The music doesn‘t
sound like
usual
Wrong speed selected. Check the record for recommended speed.
There are also records in LP format (30 cm) that
have to be played at 45 rpm (“maxi singles”) and
small records in single format (17 cm) that have to
be played at 33 rpm (so-called “ EP‘s“).
The turntable is spinning too
fast/too slow. Start the self-calibration using the operating instructions.

User manual / Bedienungsanleitung
Page / Seite 16 © clearaudio electronic GmbH
7. Technical data
Construction details: • Resonance-optimised turntable.
• Upper layer incorporates high-tech satined plastic compound.
• Chassis comprises medium-density wood bre (silver / black) or
pressure-formed solid wood (wood / dark wood).
• Bottom plate medium-density wood bre
• Height-adjustable turntable feets.
Speed options: 33 ⅓, 45rpm
Drive unit: • Decoupled and resonance damped 12V DC motor.
• Flat belt-drive
• Plug-in power supply unit, designed for worldwide use with all
networks and power frequencies.
• „IMS light – Innovative Motor Suspension“
(Suspension design of the motor using O-rings)
• „TSC“ Tacho speed control (speed monitoring)
Automatic compensation of friction and temperature changes
on platter bearings and belts
Bearing: Polished and tempered steel spindle in a sintered bronze bushing,
running on a teon thrust-pad.
Platter: 30mm / 1.18 inch main platter, made out of synthe-
tic material with high-density and excellent dimension /
precision CNC machined aluminium sub-platter.
Speed accuracy
(measured): ± 0,05%
Power consumption: Max. consumption: 3.6 watts
Consumption in operation: 1.92 watts
Standby: 0.74 watts
O mode: 0.0 watts (switched o at the rear)
Total weight: Approx. 7.5kg (incl. tonearm and cartridge)
Dimensions (W/D/H): ca. 420 x 350 x 125 mm (mit Tonarm)
Dimensions (W/D/H): Approx. 16.54 x 13.78 x 4.92 inches (with tonearm)
Manufacturer’s
warranty: 2 years*

User manual / Bedienungsanleitung
Made in Germany Page / Seite 17
Loving music
Sehr verehrte clearaudio – Kundin, sehr verehrter clearaudio – Kunde,
bei seiner Markteinführung im Jahr 2009 hat der concept bereits für Furore gesorgt.
Als Einsteigerpaket mit eigens entwickeltem Tonarm und Tonabnehmer wurde ein revolutionäres
Klangpaket mit unangefochtenen Preis-, Design- und Leistungsverhältnis geschaen und erfreut
sich mit über 20.000 verkauften Exemplaren weltweiter Bekanntheit.
Nach mehr als 10 Jahren Beständigkeit bekommt der concept ein Update und wird zum concept
Signature .
Die neue Steuertechnik mit integrierter Selbstkalibrierung, neuen Einstellungsmöglichkeiten und
zusätzlichem Tacho-Speed-Control („TSC“) erzielt noch bessere Messwerte im Gleichlauf und Impuls-
Festigkeit.
Das neue Design der Oberäche mit Sensor-Schalter vereint nun auch variable Einstellmöglichkeiten
und Funktionen, gleichzeitig dient der neue Encoder auch als Basis für weitere Generationen und
Ausbaustufen. Hinzu kommt die verbesserte Motoraufhängung durch mehrere O-Ringe („IMS“), die
den Motor vollständig vom Chassis entkoppeln und in vereinfachter Form vom Reference Jubilee
übernommen wurde.
Der concept Signature ist ein weiterer Meilenstein und das Ergebnis unserer konsequenten Forschung
und stetigen Weiterentwicklung unserer Produkte.
Um die volle Qualität des concept Signature Laufwerkes nutzen zu können, lesen Sie bitte diese
Bedienungsanleitung aufmerksam durch. Alle Hinweise dienen dazu, Ihnen viele Jahre Musikgenuss
zu bereiten und Fehlbedienungen zu vermeiden.
Wir bedanken uns bei Ihnen für Ihr Vertrauen und wünschen Ihnen viel Freude mit Ihrem neuen
clearaudio concept Signature Laufwerk.
clearaudio electronic GmbH

User manual / Bedienungsanleitung
Page / Seite 18 © clearaudio electronic GmbH
Abdeckhaube für concept Signature Plattenspieler
(Art. Nr. AC168)
concept clamp
(Art. Nr. AC122)
Ersatzriemen für
concept Serie Plattenspieler
(Art. Nr. AC123)
Diese und viele andere Zubehörartikel nden Sie im clearaudio Onlineshop (www.analogshop.de)
oder über Ihrem Fachhändler.
Passendes Zubehör von clearaudio:
Professional Power 12V Trafo-Netzteil
(Art. Nr. EL039/S)
Auch in schwarz erhältlich.
smart power 12V Akku-Netzteil
(Art. Nr. EL035/B/S)
Auch in komplett schwarz erhältlich.

User manual / Bedienungsanleitung
Made in Germany Page / Seite 19
Loving music
Sicherheitshinweise
1. Allgemeine Hinweise
Überprüfen Sie das Gerät vor der Inbetriebnahme auf vorhandene Schäden.
Ist das Gerät beschädigt, sollten Sie es nicht am Stromnetz anschließen!
Schließen Sie das Gerät niemals an, wenn es heruntergefallen oder nass geworden ist.
Kontaktieren Sie Ihren Händler um das Gerät überprüfen zu lassen.
Setzen Sie das Gerät niemals Regen oder Feuchtigkeit aus.
Das Netzkabel des Gerätes niemals mit feuchten oder nassen Händen anfassen.
Die regelmäßige Sichtkontrolle einer eventuell defekten Isolierung der Anschlussleitung ist darüber hinaus zu Ihrer
eigenen Sicherheit empfehlenswert. Eine beschädigte Zuleitung sofort vom Fachmann auswechseln lassen!
Ziehen Sie niemals am Netzkabel um das Gerät auszustecken, sondern direkt am Stecker!
Das Innere des Gerätes ist wartungsfrei, önen Sie niemals das Gehäuse oder versuchen Sie das Gerät selbst zu
reparieren. Dies kann zudem zu Garantieverlust führen.
Sollten Sie das Gerät über einen längeren Zeitraum nicht betreiben, empfehlen wir, das Netzteil vom Stromnetz zu
trennen.
Der Plattenspieler besitzt keine automatische Endabschaltung. Sobald die Auslaufrille erreicht ist, muss der Tonarm
mittels Handlift von der der Platte gehoben und der Plattenspieler manuell abgeschaltet werden.
Nicht für Kinder geeignet! Lieferumfang kann verschluckbare Kleinteile enthalten.
2. Bestimmungsgemäßer Gebrauch
Der concept Signature ist ein Plattenspieler, zur Wiedergabe von Schallplatten.
Der bestimmungsgemäße Gebrauch des concept Signature Laufwerks ist die Verwendung in Übereinstimmung mit den
in der Bedienungsanleitung bereitgestellten Informationen.
Das Netzteil darf dabei nur mit den maximal zulässigen Anschlusswerten, gemäß den technischen Daten betrieben
werden. Nicht bestimmungsgemäß ist jegliche andere Verwendung oder die Modizierung des Netzteils.
3. Aufstellungsort
Das Gerät sollte nur auf ebenen Untergründen aufgestellt werden.
Vermeiden Sie Aufstellungsorte mit direkter Sonneneinstrahlung, Temperaturschwankungen sowie hohe Luftfeuchtigkeit.
Ebenso sollten Sie Elektrogeräte nicht in der Nähe von Heizungen, Heizlampen oder anderen Geräten platzieren die
Wärme produzieren.
Das Gerät ist für den Betrieb in beheizten Räumen konzipiert.
Auf dem Gerät dürfen keine Gegenstände mit oener Flamme aufgestellt werde (brennende Kerzen o.Ä.).
4. Überlastung
Das Produkt ist so konstruiert, dass es alle nötigen Sicherheitsbestimmungen einhält, dennoch sollten Sie das Gerät bei
extremer Belastung nicht unbeaufsichtigt lassen.

User manual / Bedienungsanleitung
Page / Seite 20 © clearaudio electronic GmbH
5. Pege
Bitte verwenden Sie zur Reinigung der Acrylglaselemente nur speziellen Acrylglasreiniger und keinesfalls Spiritus oder
andere auf Alkohol basierende Flüssigkeiten (Gefahr von Oberächenbeschädigung!).
Verwenden Sie auf keinen Fall aggressives Reinigungsmittel.
Verwenden Sie zum Reinigen keine trockenen Tücher, da dies elektrostatische Auadung erzeugt.
Geeignete Reinigungs- und Pegemittel von clearaudio sind über www.analogshop.de oder über den Fachhandel
erhältlich.
Das Plattentellerlager sollte je nach Beanspruchung etwa alle zwei Jahre mit dem mitgelieferten Lageröl geschmiert
werden. Es genügt, wenn Sie hierzu etwa 1 bis 2 Tropfen in die Lagerbuchse des
concept Signature Laufwerkes geben.
6. Gesundheitshinweise
Dauerhaft hohe Lautstärke kann zu diversen Schädigungen des Gehörs führen.
Gehen Sie verantwortungsbewusst mit hohen Lautstärken um!
7. Service
Das
concept Signature Laufwerk darf während der Garantiezeit nur vom Hersteller oder authorisierten Händler repariert
werden, ansonsten erlischt der Garantieanspruch. Der Service für alle clearaudio Produkte sollte ausschließlich beim
Fachhändler erfolgen.
Sollte trotz des hohen Fertigungsstandards ein Service erforderlich werden, muss der clearaudio concept Signature
über Ihren Fachhandel an clearaudio eingeschickt werden.
8. Transport
Beim Transport des clearaudio concept Signature stets die Originalverpackung verwenden. Achten Sie darauf, das
Gerät genauso zu verpacken, wie es ausgeliefert wurde. Nur in originalverpacktem Zustand ist ein sicherer Transport
gewährleistet. Beim Verpacken umgekehrt verfahren, wie bei dem Aufbau und der Inbetriebnahme beschrieben.
Dabei ist unbedingt auf korrekte bzw. sichere Verpackung zu achten (Originalverpackung).
Bitte entfernen Sie zum Transport den Plattenteller vom Laufwerk und sichern Sie den Tonarm und den Nadelschutz des
Tonabnehmers zusätzlich mit einem Klebestreifen.
Falls Sie Ihr concept Signature Laufwerk transportieren oder versenden wollen, achten Sie bitte darauf, dass der
Plattenteller immer mit der ausgefrästen Seite nach oben in die untere Verpackungsebene eingepackt wird und dass die
Laufwerksfüße wieder zurück geschraubt werden!
Clearaudio kann für Schäden, die beim Transport entstehen und die durch falsches Einpacken verursacht wurden,
keine Haftung übernehmen.
9. Entsorgung
Dieses Produkt darf nicht zusammen mit Restmüll entsorgt werden.
WEEE Reg.Nr.: DE26004446
10. CE-Markierung
Dieses Elektronikprodukt entspricht den gültigen Richtlinien zur Erlangung des CE-Zeichens.
