ClearSpan R035B00000F User manual

1
Revision date: 11.02.10
©2010 ClearSpan™
All Rights Reserved. Reproduction
is prohibited without permission.
STK# DESCRIPTION
R035B00000F Rafter Kit for 35' Wide
ClearSpan™
35' Wide Rafter Kit with Mounting Feet
Photo may show a building of a different length and width.

2Revision date: 11.02.10
ATTENTION: The pre-punched purlin mounting holes in the short rafter
section are not spaced evenly. Before assembly, measure from the end
of the short rafter section to the set of pre-punched purlin mounting
holes that is 39-7/16" (more or less) from the end. Position that section
of the short rafter toward and connect it to the chevron, which will be at
the top of the assembled rafter.
Repeat this procedure for all rafter assemblies to ensure that the purlin
mounting holes remain aligned throughout the length of the frame. If the
purlin holes do not align during the frame assembly, verify that all rafters
are assembled as shown on this page and throughout this manual.
Consult the diagrams below and all rafter diagrams throughout this
manual before you assemble the rafter.
Short Rafter Section Short Rafter Section
Rafter Assembly Instructions
Ground Level
Rafter Leg
(CFG072ANCS003) Rafter Leg
(CFG072ANCS003)
Mounting Foot
(108500)
Mounting Foot
(108500)
Strut
(108938)
Strut
(108938)
Rafter Section
(
CFG035PC16GS05 )
Rafter Section
(
CFG035PC16GS04 )
Rafter Section
(
CFG035PC16GS05 )
Rafter Section
(
CFG035PC16GS04 )
33-7/16"
39-7/16"
33-7/16"
39-7/16"
End of Short
Rafter Section
End of Short
Rafter Section
ATTENTION: During the rafter assembly, verify
that you have positioned the long end of the short
rafter section—approximately 39-7/16" from the
end of the section to the purlin mounting holes—
toward the peak of the assembly.
See the Over-the-Top diagram at the end of this
manual and Page 6 for additional details.
39-7/16"
33-7/16"
Short Rafter Section
Pre-Punched Purlin
Mounting Holes
Chevron
Joggled End of the
Long Rafter Section
Purlin Purlin
Assembled Rafter
39-7/16"
39-7/16"
33-7/16"
33-7/16"
End of Short
Rafter Section
End of Short
Rafter Section

3
Revision date: 11.02.10
Side Profile Connection Details
When additional rafters are added to a standard building to change the rafter spacing from 6' on-center to 4' on-center,
cable patterns may change for some building lengths. The Side Profile diagrams in this guide show the cable patterns
for buildings with 4' on-center rafter spacing. Use the diagrams for your building during the assembly.
REMEMBER: A standard building has 6' on-center rafter spacing. The diagrams in this guide show frames with 4' on-
center rafter spacing. This 110644 kit is not used when additional rafters are purchased to lengthen the original building.
The diagrams on this page correspond to the details circled on the main Side Profile diagrams found on the remaining
pages. Some details may not apply to some frame lengths. In some instances, the cable bracket shown in Detail A and
Detail B is used to secure two (2) cables or four (4) cables. To secure two (2) cables, use two of the connection points on
the 108874 bracket only. Actual angle of the cable runs may vary from the detail. Consult the Side Profile diagrams.
Use the components contained in the 110644 adaptor kit sent with your building. This kit is used for all building widths
and lengths. Some components may not be needed for your building. Consult the diagrams in this guide to determine
what components of the kit are needed for your building when rafter spacing is 4' on-center.
ATTENTION: REPLACE
THE ORIGINAL STRUT
108872 WITH THE
SHORTER 108871
STRUT INCLUDED IN
THIS ADAPTOR KIT.
108874
CABLE ASSEMBLY
CABLE ASSEMBLY
AS2167
(SHACKLE)
DETAIL D
RAFTER
CABLE ASSEMBLY
CABLE ASSEMBLY
AS2167
(SHACKLE)
EYE BOLT (108868)
LOCK WASHER(FAMA38B)
3/8" HEX NUT (FALB04B)
DETAIL C
DETAIL B
DETAIL A
108874
FAME08B
(3/8” FLAT WASHER)
108503
(CABLE BRACKET)
Adaptor Kit #110644 contains these parts:
108874 Double Roll Form Cable Connection Plate 2
108868 3/8" Cable Eye Bolt (welded shut) 1
FAME08B 3/8" at washer (zinc) 1
FALB04B 3/8"-16 nut (zinc) 1
FAMA38B 3/8" lock washer (zinc) 1
108503 1/8" steel cable bracket (135 degree) 1
108871 7' Strut 1.66 14g single punch (82") 4

4Revision date: 11.02.10
Side Profile - 35' x 36' (4' Rafter Spacing)
Use these parts from the 110644 adaptor kit for your 35' x 36' building:
108874 (See Detail A.) Double Roll Form Cable Connection Plate 2
108871 (See note above.) 7' Strut 1.66 14g single punch (82") 4
ATTENTION: REPLACE THE ORIGINAL BUILDING STRUT (108872)
WITH THE 108871 STRUT INCLUDED IN THIS KIT.
4'-0"
(on-center)
(on-center)
36'-0"
GROUND LEVEL
AA
108871 Strut
included with kit.
108871 Strut
included with kit.
Rafters
Purlins
ATTENTION: Cable pattern is the same for paneled greenhouse frames where the purlins run on top of the
rafters. Sample frame shows the purlins attached to the underside of the rafters. Your frame may differ.

5
Revision date: 11.02.10
Side Profile - 35' x 40' (4' Rafter Spacing)
Use these parts from the 110644 rafter kit for your 35' x 40' building:
108874 (See Detail B.) Double Roll Form Cable Connection Plate 2
108871 (See note above.) 7' Strut 1.66 14g single punch (82") 4
ATTENTION: REPLACE
THE 108872 STRUT SENT
WITH YOUR BUILDING
WITH THE SHORTER
108871 STRUT INCLUDED
IN THIS ADAPTOR KIT.
FOUR (4) OF THE
ORIGINAL 108873 SINGLE
ROLL-FORM CABLE
BRACKETS WILL NOT BE
USED WHEN THE RAFTER
SPACING CHANGES
FROM 6' ON-CENTER
TO 4' ON-CENTER. THIS
AFFECTS THE 35' X 40'
BUILDING ONLY.
B
(on-center)
40'-0"
4'-0"
(on-center)
GROUND LEVEL
108871 Strut
included with kit.
108871 Strut
included with kit.
Rafters
Purlins
Side Profile - 35' x 48' (4' Rafter Spacing)
ATTENTION:
REPLACE THE
108872 STRUT
SENT WITH YOUR
BUILDING WITH
THE SHORTER
108871 STRUT
INCLUDED IN THIS
ADAPTOR KIT.
Cable pattern is the
same for paneled
greenhouse frames
where the purlins run
on top of the rafters.
Sample frame shows
the purlins attached to
the underside of the
rafters. Your frame
may differ.
4'-0"
(on-center)
(on-center)
48'-0"
GROUND LEVEL
AA
D
C
108871 Strut
included with kit.
108871 Strut
included with kit.
Rafters
Purlins
Use these parts from the 110644 rafter kit for your 35' x 48' building:
FAME08B (See Details C & D.) 3/8" at washer (zinc) 1
108874 (See Detail A.) Double Roll Form Cable Connection Plate 2
108503 (See Details C & D.) 1/8" steel cable bracket (135 degree) 1
108871 (See note above.) 7' Strut 1.66 14g single punch (82") 4