Climax GatewayPro CL-DR-GWP User manual

RS-232 GatewayPro (CL-DR-GWP)
Rail Mounting
RS-232 GatewayPro is designed to be installed on a standard
35 mm wide DIN rail (EN 50022, BS 5584).
Hook the module from the top, pull down the rail mounng
clips, push the module to the rail and release the rail
mounng clips.
Screw Mounting
Screw the module to any surface through 4 corner screw
holes.
3
4
1
2
INSTALLATION GUIDE version 1.0.7
Compatible with Control4
Compatible with Control4 USA
1
11
10
9
5
5
8
7
6
2
3
4
1
1. Screw holes
2. Power connectors
3. Contact input connector
(sensor)
4. Output connectors
5. Rail mounng clips
6. Channel LEDs
7. Status LEDs
8. Control buons (1-8)
9. RS-232 jack
10. RS-485 jack
Compatible with Control4
Compatible with Control4 USA
#2
#3#4
#5
#8 #1
#6#7
#2
#3#4
#5
#8 #1 #6#7
Input Voltage
Input Current
I/O Connecons
12V-24V DC (24V DC is recommended)
210mA (for 24V DC)
C-Bus
Output
1 X RJ45
Product Specificaon
RS-232 1 X RJ45
Input
8 relay channel-8A per channel X
(rising-cage 5mm screw terminals)
1 digital dry contact input X
(rising-cage 5mm screw terminals)
12
3
Enable/disable Autosave
If autosave funcon is acvated, reconnecng main power will set all outputs to the last status
(before power outage).
In order to enable/disable autosave follow steps below consecuvely and uninterruptedly:
1. Disconnect the main power. Hold buon #1 & #2 simultaneously (buon’s and LED’s number
sequence is considered from right to le as shown in following picture)
.
2. Reconnect the main power. Release buon #2 aer LEDs #1 to #4 flashed. Then release buon #1
aer LEDs #1 and #2 flashed. Power LED will start flashing quickly.
3. Press buon #2, 4 mes.
4. To disable/enable autosave mode, press buon #1. LED #1 will display whether autosave mode is
disabled or enabled. If it is “on” the autosave mode is enable.
5. Press buon #3 to save the module address and buon #4 to cancel.
It is recommended to disable autosave unless it is needed to be enabled.

57
68
Before wiring the device, always unplug the main power.
Follow this wiring for network use of module.
From:
Control4 home controller
To:
Next Module (Data & Power)
When GatewayPro is not connected to any other Climax module, the main power may be supplied
as following diagram.
From:
Control4 home controller
From:
Main Power 12V-24V DC
Follow the diagram below to apply appropriate output/input and protect module in case of
unwanted short circuit.
C C C C C C C CNO NO NO NO NO NO NO NO
+
24V DC
-
IN 1 Ch1 Ch2 Ch3 Ch4 Ch5 Ch6 Ch7 Ch8
Contact Sensor
Main
Power Supply
24V DC
+
-
N
MODE
Circut
Breaker
MODE
Circut
Breaker
MODE
Circut
Breaker
MODE
Circut
Breaker
MODE
Circut
Breaker
MODE
Circut
Breaker
MODE
Circut
Breaker
MODE
Circut
Breaker
Any type of sensor with dry contact (free voltage)
normally open or normally close
Module’s LEDs
RS-485: This LED flashes if the module receives valid data packets and will remain “on” for 5 seconds
when the module is receiving invalid data packet from other devices in same C-Bus network.
Power: all Status LEDs flash for 1 second, then When the module is connected to main power,
“Power LED” remains “on”.
RS-232: This LED flashes if the module receives valid data packets and will remain “on” for 5 seconds
when the module is receiving invalid data packet from Control4 Home Controller .
Ch1 to Ch8 : Shows the status of module’s relays.
In some cases, when a new module is added to C-Bus network, all Status LEDs might remain
“on” for 5 seconds. This situaon must not be considered as an error.
Control Buttons
Each line output can be toggled with pushing corresponding buon.
Change Device Address
The device address is fixed to “1” and is not variable.
Never connect main power to "RS-232 GatewayPro" wrongly via "RS-232 jack". It may cause
damage to the module.
Never connect other modules to "RS-232 GatewayPro" wrongly via "RS-232 jack". it may
cause damage to the connected modules.