Cobra 602-2615 User manual

23801 E. La Palma Ave., Yorba Linda, CA 92887 Ph. 714.692.8180 Fax. [phone]
www.cobrausa-vtwin.com
01/20
CONTINUED ON PAGE 2
DOCUMENT NO. 0017 REV. B
*Cobra®recommends you always wear a helmet while riding. Please never operate your motorcycle while under
the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely.
Items Supplied >
1 - Detachable (BA) Chrome or Black Rack with
Latches
2 - 3/8” I.D. Front Mount Bushings, Chrome
2 - 3/8” I.D. Rear Mount Bushings, Chrome
4 - 3/8”-16 x 2-3/4” Flathead Screws Zinc
Application(s) >
HARLEY:
SOFTAIL: FLSB 18-20
(ONLY ABOVE MODELS AS OF JANUARY 2020)
Instruction Manual >
602-2615 / 602-2615B
Page 1 of 3
Read all instructions carefully before installing your new Cobra®product!
1. Prepare a large towel or moving blanket to set the removed saddlebags on. Start on the right side of
the motorcycle. Open the saddlebag lid, disengage rear mounting cam so red flag faces up on inner
side of saddle bag, read H.D. owner's manual if needed. Carefully remove the right saddlebag;
making sure not to scratch exhaust with the lower front saddlebag mount.
2. Remove the front bolt and saddlebag bushing from the right side fender rail, these will not be reused.
NOTE: Remove one side only so the fender does not fall, resulting in possible scratches or damage
to the fender or paint, see FIGURE 1.
3. Insert (1) 3/8”-16 x 2-3/4” supplied screw into (1) supplied front mount bushing. Place sufficient blue
Loctite on the screw threads. Install the screw and bushing into the front fender rail hole. Snug but
do not tighten, see FIGURE 2.
4. Remove the right rear fender rail screw and saddlebag bushing, these will not be reused, see
FIGURE 1. Insert (1) 3/8”-16 x 2-3/4” supplied screw into (1) supplied rear mount bushing. Place
sufficient blue Loctite on the screw threads. Install the screw and bushing into the rear fender rail
hole. Snug but do not tighten, see FIGURE 2.
FIGURE 1
REMOVE STOCK
FRONT BOLT /
SADDLEBAG
BUSHING
REMOVE STOCK
REAR BOLT /
SADDLEBAG
BUSHING

23801 E. La Palma Ave., Yorba Linda, CA 92887 Ph. 714.692.8180 Fax. [phone]
www.cobrausa-vtwin.com
01/20
Instruction Manual >
602-2615 / 602-2615B
Page 2 of 3
5. Repeat Steps 1-4 on the left side, exercising care while removing the left saddlebag.
6. Install the detachable rack onto the motorcycle by first inserting the front portions of the side plates on
to the front mounting bushings on the frame rails. Make sure the rack is seated all the way onto the
mounting bushings. See FIGURE 3.
7. Then slowly rotate the rack downward so the rear portions of the side plates slip over the rear
mounting bushings. See FIGURE 3.
FIGURE 3
REAR MOUNTING
BUSHING
DETACHABLE
LATCH KNOB
DETACHABLE
LATCH PIN
FRONT MOUNTING
BUSHING
DOCUMENT NO. 0018 REV. A
CONTINUED ON PAGE 3
FIGURE 2
FRONT
MOUNT
BUSHING /
SCREW
REAR MOUNT
BUSHING /
SCREW
FIGURE 3
REAR MOUNTING
BUSHING

23801 E. La Palma Ave., Yorba Linda, CA 92887 Ph. 714.692.8180 Fax. [phone]
www.cobrausa-vtwin.com
01/20
Instruction Manual >
602-2615 / 602-2615B
Page 3 of 3
9. Pull backward on both detachable latch knobs and then push downward on the rack to allow the rack
to sit completely on the rear mounting bushings. Then release the detachable latch knob to fully
engage the latch pin underneath the mounting kit bushing. See FIGURE 4.
10. Always check to make sure both detachable latch pins are fully engaged on the bottom of the
mounting kit bushing. Failure to fully engage the detachable latch pin could cause the rack to come
loose while riding. See FIGURE 4.
MAKE
SURE
LATCH PIN
IS FULLY
ENGAGED
UNDER
BUSHING
11. TIGHTEN, the 3/8”-16 x 2-3/4” front and rear mounting bushing screws fully to Harley original torque
specifications for fender rail screws. Verify that Loctite was used on all (4) 3/8" screws.
12. Before each ride, check to make sure the detachable latches are fully engaged underneath the
mounting bushings.
13. Check the tightness of all the screws after the first ride and after the first 500 miles.
14. Reinstall saddlebags on left and right sides of new bushings; be sure the lock cam engages securely
on rear bushing. If initially tight to get on, tap on with palm of hand from rear and will loosen up with
time.
DOCUMENT NO. 0018 REV. A
To clean your black accessory use a liquid based soap detergent, such as dishwashing soap applied with a soft cloth and
rinse with clean water. Note: Avoid abrasive cleaning methods such as granular or dry cleansers, simple green, Scotch-
Brite or steel wool pads. Abrasives may breach the coating and shorten life.
FIGURE 4
MAKE SURE
LATCH PIN
IS FULLY
ENGAGED
UNDER
BUSHING