Cobra PowrFlo 06-0467-01 User manual

® 23801 E. La Palma Ave., Yorba Linda, Ca 92887 Ph. 714.692.8180, Fax. [phone]
www.cobrausa.com
04/17 1®
*Cobra®recommends you always wear a helmet while riding. Ple ase never operate your motorcycle while under
the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely.
Items Supplied >
1 –INTAKE COVER W/ SCREEN / RING ASSEMBLY
1 –K&N® VENTURI AIR FILTER
1 –BILLET VELOCITY STACK
1 –MOUNTING PLATE
1 –SUPPORT BRACKET
1 –BOLT, M5 X 12mm, ALLEN
2 –BOLT, M6 X 16mm, ALLEN
3 –BOLT, M6 X 25mm, ALLEN
2 –BOLT, M6 X 12mm BUTTONHEAD
4 –BOLT, 1/4”-20 X 1/2”, BUTTONHEAD
3 –WASHER, INTERNAL TOOTH LOCK
1 –O-RING, 2.88 "I.D. X .125", BUNA-N
1 –BILLET BREATHER FILTER
Application(s) >
KAWASAKI VN900 2006 - 2019
Instruction Manual >
Read all instructions carefully and completely before installing your new POWRFLOTM Intake.
1. Remove the (4) bolts that hold on the stock air cleaner cover. Once the cover has been removed, loosen
the top bolt to remove the filter from air box.
2. Remove the air box by loosening the (5) allen bolts around the air inlet and the (2) hex bolts from the lower
portion of the air box. See Figure 1. Disconnect the (2) hoses, idle adjuster and air temperature sensor
connector from the air box.
3. Once the air box has been removed, unscrew the air temperature sensor and install it into the supplied
mounting plate using the supplied M5 bolt, refer to Figure 3. NOTE: Make sure the small stock o-ring
around the sensor is still intact.
4. Install the supplied billet breather filter into the upper hose (disconnected in Step 2) and clamp. Rotate the
hose so the billet breather filter is pointed to the rear and resting slightly on top of the throttle body.
5. Insert the supplied o-ring into the groove of the supplied velocity stack. NOTE: Do not attempt to stretch the
o-ring into groove; position o-ring evenly around groove and use gentle force (No tools) to push it in.
6. Bolt the velocity stack to the throttle body using the (2) supplied M6 x 16mm allen bolts and tighten. See
Figure 2.
06-0467 - 01 / 02 / 03 / 04
Page 1 of 2
DOCUMENT NO. 0017 REV. A
REMOVE (5) ALLEN BOLTS
(2 LOWER BOLTS ARE HIDDEN IN DIAGRAM)
REMOVE (2) HEX
BOLTS
FIGURE 1
FIGURE 2
VELOCITY
STACK
(2) SUPPLIED M6 X 16mm
ALLEN BOLTS
O-RING
(ACTUALLY ROUND)

® 23801 E. La Palma Ave., Yorba Linda, Ca 92887 Ph. 714.692.8180, Fax. [phone]
www.cobrausa.com
04/17 2®
Instruction Manual >
06-0467 - 01 / 02 / 03 / 04
Page 2 of 2
7. Position the mounting plate over the velocity stack (with the welded tube toward inside) and secure using
(3) supplied M6 x 25mm buttonhead bolts and (3) internal tooth lock washers, finger tighten only, Figure 3.
8. Install the supplied support bracket to the two threaded bosses near the base of the cylinders using the (2)
supplied M6 x 12mm buttonhead bolts. Secure the support bracket to the mounting plate using (1) supplied
1/4"-20 buttonhead bolt, and finger tighten. See Figure 4.
9. Fully tighten the (3) M6 x 25mm allen bolts, from Step 7, followed by the support bracket bolts, from Step 8.
10. Attach the lower hose and hose clamp that was disconnected in Step 2 to the tube on the mounting plate.
Install idle adjuster onto the support bracket retaining tab. Reconnect the air temperature sensor connector.
11. Insert the round intake screen into the chrome ring so the screen sits inside the edge of the ring. Place the
ring and screen between the legs of the naked chrome intake cover as shown in Figure 5.
12. Place the naked intake cover, ring and screen assembled in Step 11, over the air filter and align each leg to
the base mounting plate threaded holes. Be sure screen sits at a 45 ° angle to the bottom leg, and C/V
logo'd leg is at the upper left position. Insert the (3) supplied 1/4"-20 x 1/2” buttonhead bolts through the
intake cover and into the base mounting plate, see Figure 5. Double check all parts are aligned properly
and tightened securely.
DOCUMENT NO. 0018 REV. A
FIGURE 3
VELOCITY STACK
INSTALLED
SENSOR
W/ O-RING
MOUNTING
PLATE
(3) SUPPLIED M6 X 25mm ALLEN BOLTS
& INTERNAL TOOTH LOCK WASHERS
SUPPLIED M5
ALLEN BOLT
FIGURE 4
SUPPORT
BRACKET
(2) SUPPLIED M6 X 12mm
BUTTONHEAD BOLTS
1/4”-20 X 1/2”
BUTTONHEAD BOLT
CALIFORNIA CUSTOMERS:
In California, aftermarket parts that have been identified specifically
as replacement parts or that have received an Air Resources
Board Executive Order may be used on street motorcycles.
All other emissions related aftermarket parts are for competition
use only. A list of replacement parts and EO parts, and
corresponding fitment is provided at: www.cobrausa.com
FIGURE 5
MOUNTING PLATE
ASSEMBLY
INTAKE SCREEN
(3) ¼”-20 X 1/2”
BUTTONHEAD
BOLTS
C / V LOGO'D LEG
POSITIONED HERE
INTAKE COVER
(NOTE: DESIGN WILL
VARY BASED ON
PART NUMBER)
K&N®VENTURI AIR FILTER
INTAKE RING