CoCo PIR-2050 User manual

USER’S MANUAL
version 1.1
English
PIR-2050 WIRELESS MOTION SENSOR

PIR-2050 WIRELESS MOTION SENSOR
A: Letter code selector
B: Number code
selector
C: Doorbell switch
D: Time switch
E: Automatic code
switch
F: Protection cover with
“Lux” switch and
fastening clip
A
B
C
D
F
E
*
*Picture of an arbitrary COCO mains socket switch
(not included)
1

PIR-2050 WIRELESS MOTION SENSOR
2
[1] Unscrew the bracket from the motion sensor. [2] Determine the desired mounting location and
make the necessary holes. Attach the bracket to
the wall.
The standard height for a good detection
range is 3 metres!
See [12-13] for more information about the
range!

PIR-2050 WIRELESS MOTION SENSOR
[3] Use a screwdriver to firmly press the tab (under
the protection cover) inward. Now push the tab
downward to release the sensor cover.
[4] Slide the sensor cover off of the housing.
Attention: There is a seal ring between the
cover and the housing. Damage to this part may
result in leakage!
3

PIR-2050 WIRELESS MOTION SENSOR
4
[5] Install 3 batteries. Pay attention to the correct
orientation of the + and – poles (as shown on the
inside).
[6] Set the desired code. Follow the instructions in
[7 – 9].
The setting is dependent on the type of
receiver: [7] doorbell chime, [8] receiver with
manual code, or [9] receiver with automatic code.

PIR-2050 WIRELESS MOTION SENSOR
3
2
1
3
2
1
[7] Linking to doorbell chime: (1) Set “Code” to
“ML”. (2) Set the time switch to the bell symbol. (3)
Set the letter selector to the same house code as
your doorbell chime.
[8] Linking to receiver with manual code: (1) Set
“Code” to “YC”. (2) Set the switch to the desired
"switch off" time. (3) Set the number and letter
selectors to the same code as on your receiver.
Set the time switch to the bell symbol to set
the "switch off" time to 4 sec. (minimum)!
Continue with [10]!
Continue with [10]!
5

PIR-2050 WIRELESS MOTION SENSOR
6
1
2
3
4
2
1
[9] Linking to receiver with automatic code: (1) Set
“Code” to “YC”. (2) Set the switch to the desired
"switch off" time. (3) Push the search mode button
on your receiver. (4) Slide “Learn” to “Set” (the
receiver switches on and off 2x to confirm).
Continue with [10]!
[9a] Deleting a code from the memory of the
receiver: (1) Push the search mode button on your
receiver. (2) Slide “Learn” to “Del” (the receiver
switches on and off 2x to confirm).

PIR-2050 WIRELESS MOTION SENSOR
[10] Make sure the rubber seal ring is positioned
properly. Click the cover onto the housing. Press
the protection cover back in place.
Incorrect installation of the seal ring or
installation of a damaged ring can lead to leakage!
[11] Screw the motion sensor to the bracket.
7

PIR-2050 WIRELESS MOTION SENSOR
8
[12] Tilt the motion sensor (upward or downward) to the desired angle. The motion sensor can be tilted
through a total angle of 202.5 degrees.
The maximum range is 10 metres!
The sensor achieves its maximum range at a height of 3 metres and an angle of 22.5 degrees.

PIR-2050 WIRELESS MOTION SENSOR
[13] Turn the motion sensor to the desired horizontal angle. The motion sensor can be turned through a
total angle of 216 degrees.
However, the horizontal sensor range never exceeds 110 degrees!
9