AJAX DoubleButton User manual

DoubleButton User Manual
Updated October 20, 2020
DoubleButton is a wireless hold-up device with advanced protection against
accidental presses. The device communicates with a hub via the encrypted
radio protocol and compatible only with Ajax security systems. The
line-of-sight communication range is up to 1300 meters. DoubleButton operates
from the pre-installed battery up to 5 years.
DoubleButton is connected and congured via on iOS, Android,
macOS, and Windows. Push notications, SMS, and calls can notify about
alarms and events.
Buy the DoubleButton hold-up device
Functional elements
Jeweller
Ajax apps

Operating principle
DoubleButton is a wireless hold-up device, featuring two tight buttons and a
plastic divider to protect against accidental presses. When pressed, it raises an
alarm (hold-up event), transmitted to users and to the security company’s
monitoring station.
An alarm can be raised by pressing both buttons: one-time short or long press
(more than 2 seconds). If only one of the buttons is pressed, the alarm signal is
not transmitted.
All DoubleButton alarms are recorded in the feed. The
short and long presses have different icons, but the event code sent to the
monitoring station, SMS, and push notications do not depend on the pressing
manner.
DoubleButton can only operate as a hold-up device. Setting the type of alarm is
not supported. Keep in mind that the device is active 24/7, so pressing the
DoubleButton will raise an alarm regardless of the security mode.
Only are available for DoubleButton. The control mode for
is not supported.
Ajax app’s notication
alarm scenarios automation
devices

Event transmission to the monitoring station
The Ajax security system can connect to the CMS and transmit alarms to the
monitoring station in and protocol formats.
Connection
The device is not compatible with , , and third party security
control panels.
Before starting connection
Only users with administrator permissions can connect a device to a hub.
How to connect DoubleButton to a hub
Sur-Gard (ContactID) SIA DC-09
ocBridge Plus uartBridge
1. Install the . Create an . Add a hub to the app and create at
least one room.
Ajax app account
2. Check if your hub is on and connected to the Internet (via Ethernet cable, Wi-
Fi, and/or mobile network). You can do this in the Ajax app or by looking at
the Ajax logo on the front panel of the hub. The logo should light with white
or green if the hub is connected to the network.
3. Check if the hub is not armed and does not update by reviewing its status in
the app.
1. Open the Ajax app. If your account has access to several hubs, select the
hub to which you want to connect the device.
2. Go to the Devices tab and click Add device.
3. Name the device, scan or enter the QR code (located on the package), select
a room and a group (if group mode is enabled).
4. Click Add— the countdown will begin.

To connect DoubleButton to a hub, it should be located on the same protected object as
the system (within the hub’s radio network range). If the connection fails, try again in 5
seconds.
DoubleButton can be connected to one hub only. When connected to a new hub,
the device stops sending commands to the old hub. Added to a new hub,
DoubleButton is not removed from the device list of the old hub. This must be
done manually in the Ajax app.
Updating the device statuses in the list occurs only when DoubleButton is pressed and
does not depend on the Jeweller settings.
States
The states screen contains information about the device and its current
parameters. Find the DoubleButton states in the Ajax app:
Parameter Value
Battery charge
Battery charge level. Two states are indicated:
LED brightness Indicates the LED brightness level:
5. Hold any of two buttons for 7 seconds. After adding DoubleButton, its LED
will ash green once. DoubleButton will appear in the list of hub devices in
the app.
1. Go to the Devices tab .
2. Select DoubleButton from the list.
• ОК
• Battery low
• Off — no indication
• Low

Works via *range extender name*
Indicates the status of the ReX range extender
use.
The eld is not displayed if the device
communicates directly with a hub
Temporary Deactivation
Indicates the status of the device:
Firmware DoubleButton rmware version
ID Device ID
Setting up
DoubleButton is set up in the Ajax app:
Please note that after changing the settings, you need to press Back to apply them.
Parameter Value
First eld
Device name. Displayed in the list of all hub
devices, SMS, and notications in the event
feed.
The name can contain up to 12 Cyrillic
characters or up to 24 Latin characters
• Max
• Active
• Temporarily deactivated
Learn more
1. Go to the Devices tab .
2. Select DoubleButton from the list.
3. Go to Settings by clicking on the icon.

Room Selecting the virtual room to which
DoubleButton is assigned. The name of the
room is displayed in SMS and notications in
the event feed
LED brightness
Adjusting LED brightness:
Alert with a siren if button is pressed
When enabled, the connected to your
security system signal about the button
pressing
User Manual Opens the DoubleButton user manual
Temporary Deactivation
Allows the user to disable the device without
removing it from the system. A temporarily
deactivated device will not raise an alarm when
pressed
Unpair device Disconnects DoubleButton from a hub and
removes its settings
Alarms
A DoubleButton alarm generates an event notication sent to the security
company’s monitoring station and system users. The pressing maner is
indicated in the event feed of the app: for a short press, a single-arrow icon
appears, and for a long press, the icon has two arrows.
• Off — no indication
• Low
• High
sirens
Learn more about temporary
deactivation of devices

To reduce the probability of false alarms, a security company can enable the
feature.
Note that the alarm conrmation is a separate event that does not cancel the
alarm transmission. Whether or not the feature is enabled, DoubleButton alarms
are sent to a CMS and to security system users.
Indication
DoubleButton blinks red and green to indicate command execution and battery
charge status.
Category Indication Event
Pairing with a security system
The whole frame blinks green
6 times
The button is not connected to
a security system
The whole frame lights up
green for a few seconds
Connecting the device to a
security system
Command delivery indication The frame part above the
pressed button lights up green
briey
One of the buttons is pressed
and the command is delivered
to a hub.
alarm conrmation

When only one button is
pressed, DoubleButton does
not raise an alarm
The entire frame lights up
green briey after press
Both buttons are pressed and
the command is delivered to a
hub
The entire frame lights up red
briey after press
One or both buttons were
pressed and the command
was not delivered to a hub
Response Indication
(follows the Command
Delivery Indication)
The whole frame lights up
green for half a second after
the command delivery
indication
A hub received DoubleButton
command and raised an alarm
The whole frame lights up red
for half a second after the
command delivery indication
A hub received DoubleButton
command but did not raise an
alarm
Battery status indication
(follows Feedback Indication)
After the main indication, the
entire frame lights up red and
gradually goes out
The battery replacement is
required. DoubleButton
commands are delivered to a
hub
Application
DoubleButton can be xed on a surface or carried around.

How to x DoubleButton on a surface
To x the device on a surface (e. g. under a table), use Holder.
To install the device in the holder:
1. Choose a location to install the holder.
2. Press the button to test whether the commands are delivered to a hub. If
not, choose another location or use the .
When routing DoubleButton through ReX, keep in mind that it does not
automatically switch between a range extender and a hub. You can assign
DoubleButton to a hub or another ReX in the Ajax app.
ReX radio signal range extender
3. Fix Holder on the surface using the bundled screws or double-sided
adhesive tape.
4. Put DoubleButton into the holder.

Please note that Holder is sold separately.
Buy Holder
How to carry DoubleButton
The button is easy to carry around thanks to a special hole on its body. It can be
worn on the wrist or neck, or be hanged on a keyring.
DoubleButton has an IP55 protection index. Which means that the device body
is protected from dust and splashes. And a special protective divider, tight
buttons, and the need to press two buttons at once eliminate false alarms.
Using DoubleButton with alarm conrmation enabled
Alarm conrmation is a separate event that a hub generates and transmits to a
CMS if the hold-up device has been activated by different types of pressing
(short and long) or two specied DoubleButtons have transmitted alarms within

a specied time. By responding to conrmed alarms only, a security company
and police reduce the risk of unnecessary reacting.
Note that the alarm conrmation feature does not disable the alarm
transmission. Whether or not the feature is enabled, DoubleButton alarms are
sent to a CMS and to security system users.
How to congure conrmation of a hold-up device
How to conrm alarm with one DoubleButton
To raise a conrmed alarm (hold-up event) with the same device, you need to
perform any of these to actions:
How to conrm alarm with several DoubleButtons
To raise a conrmed alarm (hold-up event), you can activate one hold-up device
twice (according to the algorithm described above) or activate at least two
different DoubleButtons. In this case, it doesn’t matter in what way two different
DoubleButtons were activated — with a short or long pressing.
1. Hold both buttons simultaneously for 2 seconds, release, and then press
both buttons again briey.
2. Simultaneously press both buttons briey, release, and then hold both
buttons for 2 seconds.

Maintenance
When cleaning the device body, use products suitable for technical
maintenance. Do not use substances containing alcohol, acetone, gasoline, or
other active solvents to clean DoubleButton.
The pre-installed battery provides up to 5 years of operation, considering one
pressing per day. More frequent use may decrease battery life. You can check
the battery status at any time in the Ajax app.
If DoubleButton cools down up to -10°C and below, the battery charge indicator
in the app can show low battery status until the button heats up to above-zero
temperatures. Note that the battery charge level is not updated in the
background, but only by pressing DoubleButton.
When the battery charge is low, users and a security company monitoring
station receive notication. The device LED smoothly lights up red and goes out
after each button pressing.
Technical Specications
How long Ajax devices operate on batteries, and what affects this
How to replace the battery in DoubleButton

Number of buttons 2
LED indicating command delivery Available
Protection against accidental press
Frequency band 868.0 – 868.6 MHz or 868.7 – 869.2 MHz,
depending on the sales region
Compatibility Operates only with and
on OS Malevich 2.10 and higher
Maximum radio signal power Up to 20 mW
Radio signal modulation GFSK
Radio signal range Up to 1,300 m (line-of-sight)
Power supply 1 CR2032 battery, 3 V
Battery life Up to 5 years (depending on the frequency of
use)
Protection class IP55
Operating temperature range From −10°С to +40°С
Operating humidity Up to 75%
Dimensions 47 × 35 × 16 mm
Weight 17 g
Complete set
• To raise an alarm, press 2 buttons
simultaneously
• Protective plastic divider
Ajax hubs range
extenders
1. DoubleButton
2. CR2032 battery (pre-installed)
3. Quick Start Guide

Warranty
The warranty for the AJAX SYSTEMS MANUFACTURING Limited Liability
Company products is valid for 2 years after purchase and does not extend to the
bundled battery.
If the device does not function properly, we recommend that you rst contact
the support service as technical issues can be resolved remotely in half of the
cases!
Technical support:
Warranty obligations
User agreement
suppor[email protected]
Need help?