Coffee Queen Empire Hot User manual

Service manual
Rev. 100426
S / EN
Empire Hot
COFFEE QUEEN
Your retail dealer
...............................................................................
...............................................................................
CoffeeQueen_SV.jpg

1. Table (list) of contents.
1. Table of contentssid. 2
2. General 3
3. Overview of components front 4
3. Overview of components mixing system 5
4. SERVICE; Installation and start
Place the brewer 6
Connectings: Electricity - Water 6
Starting up machine 6
Fill canister with ingredients 7
5. OPERATION
Making coffee in a cup 8
6. CLEANING
Weekly cleaning
Dismantle mixing system 9
Washing parts9
Reassemble mixing system 10
7. CLEANING programs:
Automatic cleaning of mixing bowl (only): 11
Automatic cleaning of mixing bowl 1 or 2 12
Automatic cleaning of In/Outlet valves: 13
8. Cup counter and Easy access 14
9. Safety functions 15
10. Failure messages 15
11. Storage / Transport. 15
12. Dimension sketch 16
13. Cleaning and maintenance 17
14. Circuit diagram 18
15. Spare parts list 19-21
16. Exploded View 22-28
2.

2. General. Empire Hot
We congratulate to your choice of a Coffee Queen coffee machine.
Please read this manual before you take the machine into operation for the first time.
Alwayskeepthismanualwithinreachfortheuser!
Coffee Queen / Empire hot
-making coffee cup by cup
-8 choices of drinks,
-2 - 4 ingredients canisters,
-electronicallytemperaturecontrolled
-adjustablecoffeestrength
-clockfunctions
Facts:
Height 620 mm
Width 310mm
Depth 490mm
Electricity 230V/2200W
Water connection ½”outside thread
3.

4.
3. Overview of components , front Empire Hot
Outlet
drinks
Strengthofdrinks
++ or - -
Choices of
drinks
Drip tray
insert
Drip tray
Keyswitch
cupandjug
choice)
Display
Door
lock

3. Overview of components , mixer system Empire Hot
5.
Empire cold: 4 canisters.
Canister: Width Depth Height Volume/litre;
coffee 67 225 200 1,15
espresso 67 225 200 1,15
chocolate 67 225 200 1,15
topping 67 225 200 1,15
Chute
Ingredients
canister
ON/OFF-
switch
Steam trap
Mixing bowl
Outlet
drinks
Service
opening
emptying
watertank

6.
ON / OFF
switch
4. Service. Installation and start Empire Hot
1. Place the brewer on a flat Connect the electrical plug to a separate
levelandwaterproofsurface. groundedwallsocket
Grounded wall socket
230V 10A
OBSERVE!
Make sure there is a space behind
the machine for free flow of air.
( minimum 10cm ).
2. Connect attached water tube to cold water with an R 1/2”.
Makesurethatthewaterhosenotarekinkedanywherewhenmachineis
pushedintoplace.
Please flush the water tube before connecting to machine, this to avoid any
particles to damage the inlet valve.
3. Openthewaterinlet.
4. Turn on the ON-OFF switch insidethedoor.
Water is been filled into the tank automatically
with2,0litresofwater.Theheatingwillnot
startbeforethewaterlevelreachesthe
levelsensor.
Set temperature is approx. 85ºC.
5. Close door.

7.
4. Service. Installation and start Empire Hot
6. Fill canisters with ingredients.
Takeout(thistoavoidunnecessary spillage in
themachine)ingredientcanistersandfillthem
withingredients.
1. Loosencanister.
2. Removelidandfillcanisterwith
ingredients.
Reassemblecanisters.
7. When placing the ingredient canisters;
Makesurethattheoutletpipes on the ingredient canisters are touching
the steam traps (A).
(A).
(A).

1. Place a cup in the centre of the cup holder
2. The strength has a standard setting,
ifyou wish to increase or decrease it, do as
follows ifnot continue to point 3.
Stronger drink;
Increase by pushing + or ++ for 5% or 10%
alternative
Weaker drink;
Decrease by pushing - or -- for 5% or 10%
(the indication lamp will go up or down
depending of choice).
3. Choosedrinkbypushingonthebuttontothe
rightofeachmenu
The display will show; ”Please wait”
Wait until the text ”Please wait”hasbeen
turnedoffbeforeyoutakeyourcup.
Enjoyyourdrink.
8.
5. Operation; Making coffee in a cup Empire Hot
2.
3.
1.

9.
6. CLEANING: Weekly cleaning Empire Hot
(D)
Dismantle : Mixer system
1.
Loosenoutlethose(A) and
turnlockknob(B)
anti-clockwise.
3.
Loosen whipper (D) pull
whipperstraight out from the
machine.
(E)
(A)
(B) (C)
Cleaning
Wash these parts:
.6.
A. Mixerbowl
B. Steam trap
C. Whipper
D. Assembly plate
NOTE!
Make sure this parts are dry
before use
2.
Loosenmixerbowl.
Pullapart(C).
4.
Turn lock knobanti-
clockwise.(E) untilit stops
5. Clean with a wet rag and
droughtdrily.

10.
6. CLEANING: Weekly cleaning Empire Hot
REASSEMBLE: Mixer system
7.
Reassembletheassemblyplateby turning
lock knob (F) clockwise. INSPECT gaskets.
pil (G).
9.
Assemblewhipper,pulluntil
you hear a clicking noise. (H).
10.
Assemble mixer bowl and steam
trap (J) see picture.
11.
Easilypushthemixerbowl
towards, according to(K) and lock
withlockknob(L).Connectoutlet
hose(M).
(NOTE! make sure that all water
hose are connected at right place
(H)
(J)
(J)
(J)
(K)
(M)
(L)
(G)
FF
F
8.
Make sure that the motor whippers plane side
will be in accordance with the whippers plane
side. see next (G) and picture (H).
INSPECT
INSPECT

The mixer bowls can easily be cleaned with the key switch in ”cup” (normal)
position. Daily automatic cleaning of mixing system must be done once a day.
11.
7. CLEANING: Cleaning program: Daily Empire Hot
1. Place a jug in the drip tray.
2. Turn the key slowly ninetydegreesandbackagain.
3. Push button for drink 1 for 6 seconds.
After 6 seconds the mixer bowl starts to be
cleaned in max.10 seconds.
The display shows:
”Cleaning Mixer 1”. (in 5 sec.)
”Cleaning Mixer 2”. (in 5 sec.)
Automatic cleaning of mixing system.
2.
3.

Themixerbowlscaneasilybecleanedwiththe key switch in ”cup” (normal) position.
12.
7. CLEANING: Cleaning program Empire Hot
Automatic cleaning of mixing bowl 1 or 2
1. Place a jug in the drip tray.
2. Turn the key slowlyninetydegreesandback
again.
3. Push button for drink 2 for 6 seconds.
To cleaning mixing bowl 1
or
4. Push button for drink 3.
To cleaningmixing bowl2.
After 6 seconds the mixer bowl starts to be
cleanedinmax.10seconds.
The display shows: ”Cleaning Mixer 1”,
”CleaningMixer2”.
2
3
4

13.
7. CLEANING: Cleaning program Empire Hot
Automatic cleaning of In/Outlet valves:
TheIn/Outletvalvescaneasilybecleanedwiththekeyswitchin”cup” (normal) position.
1. Place a jug in the drip tray.
2. Turn the key slowlyninetydegreesandback
again.
3. Push button for drink 1 and 2 at the same
time for 6 seconds.
Hold the buttons down.
AllIn/Outlet valveswillnowstart toopenand
close with 2 pulses/second in 10 seconds or as
longas you hold the buttons
The display shows: ”Cleaning valves”.
2
3
3

14.
8. Cup counter - Easy Access Empire Hot
1
57
234
6
1
1 5
3
4
Easy Access:
Volumeand strength can be adjusted with±15%
withthekey switch in ”cup” (normal) position.
1. Push ”+” and ”-” button at the same time.
After 4 seconds the signal will go faster.
Thedisplayshows:”Easyaccess””strength 1 100%”
2. Choosethedrinkyouwant to change
bypushing”+” or”-”button.
3. Pushbutton for drink 2.
Thedisplayshows:forexample.Volume 4and”
Blinking 100%”
Changeby pushing ”+” or”-”button.
4. Pushbuttonfor drink 2 to confirm the change.
5. Press ”stop” to go back to user mode.
1. Push ”-” button for 6 seconds.
After 4 seconds the signal will go faster..
The display shows: ”Total xxx cups”
2. Pushbutton for drink 2.
The display shows: ”Choice 1 free xxx cups”
3. Pushbutton for drink 2.
The display shows ”Choice 1 coin xxx cups”
4. Pushbutton for drink 2.
The display shows ”Choice 1 xxx cups in can”
5. Push”+”buttonto reach to ”choice 2” etc.
6. Pushchoice3toresetthecounter.
7. Push ”Stop” button to go back to user mode.
Cup counter:
Themachinehasacupcounterwhichis
available to see and reset with the key switch
in”cup”(normal) position.

15.
9. Safety functions. Empire Hot
10. Failure messages.
11. Storage / Transport.
”Door open”
”Blocked”
1. Display shows: ”Blocked” ”Water level low”.
Check if water tap is open.
Turn offthemachine with themainswitch,
wait for 10 sec. and turn on again.
2. Display shows normal: but no drink is coming.
Possible cause of failure:
Mechanical stop in the ingredients canisters or
whipperhouse.
Action: Try to findthe cause of failure.
Cleanthemixer system and try again.
1.Indicationof door
Door not closed
Thedisplayshows;”Dooropen”
2. Whenmachineisnotinuse:
Valves are blocked.
Transport and no use in long time.
1. Turn offtheswitch,pull out the plug andcloseincomingwatertube.
2. Emptythe water tank.
3. Keep machine free from frost.
Long machine storage at temperatures below 0ºC can cause damage of the machine.
Totalemptyingof water is recommended.
Failure messages which can mostly be corrected without any help from service company
The machine is equipped with following
safety functions

12. DIMENSION SKETCH. Empire Hot
16.

Outside cleaning; use a
soft rag and liquid cleaning agent
to prevent scratches.
17.
13. Cleaning and maintenance. Empire hot

14. Circuit diagram.
18.

19.
Description: Art. no. Pos. no. 23 4
Levelsensorwithgasket 120548 1 1 1 1
Gasket for sensor 150118-02 2 1 1 1
Sensorpinshort 1205302 3 1 1 1
Doubleseal,levelsensor 1605362 4 1 1 1
Sensorpin long 1205301 5 1 1 1
Heating element 2200W 230V 1601361 6 1 1 1
Gasket, watertank,lid 1206591 7 1 1 1
Motorgear145 rpm, without axle 1604612 8 2 3 4
Motoraxle for 1604612, 16mm 1604614 9 2 3 4
Highlimit controll, BULBA 220220 10 111
NTCthermistor 1604133 11 111
Valve outlet, 24 V DC 120627-03 12 333
Membrane 1501191 13 333
Inlet(rubber),forvalve (transparent) 160537-03 14 333
Plug,water tank (transp.) 160538-03 15 111
Rubbergrommet , for NTCthermistor (red) 1605361 16 111
Water tank complete , 1/3 phase 710021 17 111
Siliconehoseoutlet 8x12 L=50 150501 18 222
Silicone hose coffee 8x12 L=255 150501 18 111
Silicone hose topping 8x12 L=260 150501 18 111
Silicone hose choc/topp. 8x12 L=345 150501 18 111
Siliconehoseinletandoverflow 8x12 L=430 150501 18 222
Silicone hose draining 8x12 L=710 150501 18 111
Nonreturnvalve/inlet 1206123 19 111
Note! Silicone hose (150501) sales by metre.
Steam trap 120500 20 222
Mixingbowl 1204852 21 222
Whipper 1204842 22 112
Motor whipper 24V F 7001111 23 112
Plate,motor whipper(grey) 1604592 24 222
Assemblyplate (grey) 1204781 25 112
Assemblyplate, tight (grey) 1204831 26 1 1 -
Hoseconnection, angular,(mixerbowl- outlet) 1204853 27 222
Angleof outlet (svart) 120145 28 333
O-ring red for assembly plate mod. F 120638 29 222
Slinger disc 120480 30 112
Grommet(forwhipperpin)(red) 120655-02 31 112
Bulk head adaptor mixer bowl 120498 32 222
Switch2 pol (illumin.) 160801-04 33 111
Foam for dust trap 120136 34 111
Dusttrap 253017 35 111
15. Spare part list. Empire Hot
Amount/unit

20.
15. Spare part list. Empire Hot
Amount/unit
Description; Art. no. Pos. no. 2can. 3can. 4can.
Ingredient canister compl. B67 x H 200 plast 1205622 40 -2 4
Ingredientcanistercompl.B137xH200plast 1204878 41 2 1 -
Lid 1204955 42 2 1 -
Chuteleft(FB) 120489 43 2 1 -
Feedcontrol,plast 1204712 44 2 1 -
Cage(metal) 1801451 45 2 1 -
Agitator+screwkompl. 1204733 46 2 1 -
Lid 67 B67 x H 200 1205671 47 -2 4
Fanconnection complete 1604173 49 1 1 1
Fan 24VDC 1604171 50 1 1 1
Gridcoverforfan 1604172 51 1 1 1
Valve inlet 2,5 l/min. 24VDC 1206371 52 1 1 1
Solid-staterelay 1604201 53 1 1 1
Electronic-cardVerII 1604102 54 1 1 1
Fuse 4Aslow 5x20 1604381 55 1 1 1
Mainsupplycable,Europa 160565 56 1 1 1
Inlet-plugandsocket 160570 57 1 1 1
Fuseholder 1604351 58 1 1 1
Fuse 2Aslow 5x20 1604382 59 1 1 1
Connection block PA80 160351 60 1 1 1
Gable (connection block) PA80 160352 61 1 1 1
Transformer 710150 62 1 1 1
Microswitch 160841 63 1 1 1