Cognex DataMan 60 User manual

DataMan®60
Quick Reference Guide
2019 October 08
Revision: 6.1.6SR1.5

Precautions
To reduce the risk of injury or equipment damage, observe the following precautions
when you install the Cognex product:
lRoute cables and wires away from high-current wiring or high-voltage
power sources to reduce the risk of damage or malfunction from the
following causes: over-voltage, line noise, electrostatic discharge (ESD),
power surges, or other irregularities in the power supply.
lChanges or modifications not expressly approved by the party responsible
for regulatory compliance could void the user’s authority to operate the
equipment.
lEnsure that the cable bend radius begins at least six inches from the
connector. Cable shielding can be degraded or cables can be damaged or
wear out faster if a service loop or bend radius is tighter than 10X the cable
diameter.
lThis device should be used in accordance with the instructions in this
manual.
lAll specifications are for reference purposes only and can change without
notice.
2

Product Overview
1 Internal illumination
2 3-position lens cap
3 Focal position indicator
4 External illumination connector
5Status LEDs
6 LED aimer
7Lens
1 Directly connected cable terminating in a DB15 connector providing: power, I/O, USB, and
RS-232 connectivity
2 Ethernet RJ-45 connector
3 Mounting points
3

DataMan 60 Accessories
CABLES
USB Cable, 1.5 m (DM100-USB-000),
USB Cable, 3 m (DM100-USB-030)
USB and Flying Leads I/O Cable, 2.0 m (DM-USBIO-00)
RS-232 and Flying Leads I/O Cable, 2.5 m (DM-RS232IO-00)
RS-232 Cable, 1.5 m (DM100-RS232-000),
Extension Cable, 5 m (DM100-EXTCBL-000)
Flying Leads Connection Cable, 5 m (DM50-PWRIO-05)
RS-232/USB adapter connector (DM100-PATCH-000)
Ethernet Cable: use CBL-C10E or any standard CAT5/5e, SF/FTP or S/FTP
cable
OTHER
Power Supply, 6 V (DM100-PWR-000)
Pivot Mounting Bracket (DM100-PIVOTM-00)
Universal Mounting Bracket (DM50-UBRK-000)
Control Box (DM-CTRLBOX-00)
4

Dimensions
5

Field of View and Reading Distances
Focus position Distances in mm/2D min. code Distances in mm/1D min. code
45 mm 33-51 6 MIL 34-51 4 MIL
31-57 8 MIL 30-56 6 MIL
27-60 10 MIL 37-66 10 MIL
25-61 12 MIL
70 mm 44-74 6 MIL 52-73 4 MIL
42-78 8 MIL 45-83 6 MIL
39-80 10 MIL 33-89 10 MIL
34-89 12 MIL
110 mm 58-121 10 MIL 66-122 6 MIL
54-133 12 MIL 50-141 10 MIL
58-168 15 MIL
6

Connecting the Reader
Perform the following steps:
1. Connect the breakout cable.
2. Connect the reader to the PC.
3. Connect the reader to an Ethernet network with a standard CAT5/5e,
SF/FTP or S/FTP cable.
For information on the pinout and the wire colors, see section Connections, Optics
and Lighting in the DataMan 60 ReferenceManual.
7

Installation
Installation procedures and specifications are presented in detail in the DataMan®60
Reference Manual, which is installed with the DataMan Setup Tool. From the
Windows Start menu, select the following to access the manual: All Programs >
Cognex > DataMan Software vx.x.x > Documentation.
Note:
lCables are sold separately.
lIf a standard component is missing or damaged, immediately contact
your Cognex Authorized Service Provider (ASP) or Cognex
Technical Support.
CAUTION:All cable connectors are keyed to fit the connectors on the reader.
Do not force the connections or damage may occur.
Mounting
Mounting the DataMan reader at a slight angle (15°) can reduce reflections and
improve performance.
Use the set of mounting holes on the rear part to mount the DataMan reader.
8

Connect the Ethernet Cable
1. Connect the Ethernet cable's RJ-45 connector to a switch/router or PC, as
applicable.
Connect the Breakout Cable
Note: You can clip unused wires short or use a tie made of non-conductive
material to tie them back. For RS-232, use the Power Supply return path for
ground.
1. Verify that the power supply being used is unplugged and not receiving
power.
2. Connect the cable on the back of the device to an RS-232 adapter cable
with power tab.
3. Connect a 6 V power supply.
4. Restore power to the power supply and turn it on if necessary.
9

Install Software and Documentation and
Connect the Reader
Follow the steps below to connect your reader to power and network:
1. Connect the RS-232 cable to your reader.
2. Connect the cable to a power supply.
To configure a DataMan 60 reader, the DataMan Setup Tool software must be
installed on a networked PC. The DataMan Setup Tool is available from the
DataMan support site: http://www.cognex.com/support/dataman.
1. After installing the software, connect the DataMan 60 reader to your PC.
2. Launch the DataMan Setup Tool and click Refresh.
3. Select your DataMan 60 reader from the list and click Connect.
10