Coleman Tent 9250-147 User manual

Connect Frame to Tent
– Locate the pin & ring systems on
either side of the front door and the
corresponding pin & rings on the back
side of tent.
– Insert one end of black frame pole onto
pin & ring system on tent stake loop on
either side of front door. (illus. 3)
– Go to opposite end of pole diagonally
from starting point and gradually apply
pressure to the pole forming an arch
until you are able to insert the pin into
pole end.
– Repeat for second pole.
– Attach tent frame clips to poles.
Montana Big Sky™14’x7’
1Layout & Positioning
of Tent, Pole Assembly
– Layout and position tent with door
facing desired direction. (illus. 1)
– Unzip door.
– Stake down tent corners, using the
tent stake loops. Keep the floor taut.
(illus. 2)
– Assemble all poles by interlocking
shock-corded poles.
– Insert the black poles into center pole
sleeves marked with black binding.
The poles should cross forming an
“X” in the middle of tent. (illus. 1)
2
When You Are Ready
To Set Up Your Tent
– Select a level campsite clear of
rocks, branches and other hard or
sharp objects.
– Do not set up your tent under trees.
– For best results in windy conditions,
position the end of tent into the wind.
(2) Side Tent
Poles (Grey)
(2) Main Tent Poles
(Black)
POLE ASSEMBLY PARTS
Front door
Instructions apply to Part Number 9250-147
illus. 1
illus. 2 Tent
stake through
stake loop
illus. 4
Center section upright
Part No. 9278A242
Part No. 9278A243
illus. 3
pin & ring system located
on the front & rear of tent
Black poles Black poles
Rainfly Part No.
9278B245
(2) Rainfly Poles
Part No. 9278B244

THE COLEMAN CO., INC.
3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN SRI LANKA
PRINTED IN SRI LANKA Rev. 11/04
Things You Should Know
• Under certain conditions (cold weather, high humidity, etc.)
condensation will form on the inside surfaces of your tent. Condensation is
caused by water vapor from your breath, perspiration, or any wet clothing
inside your tent. It is NOT LEAKAGE through the tent fabric. It can be
minimized by removing wet clothing from your tent and by providing good
ventilation through the tent.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles inside
your tent. Use a separate storage bag.
• STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF.
NEVER PULL ON THE TENT FABRIC OR TENT STAKE LOOP TO
REMOVE STAKE.
• TENT POLES SHOULD NOT BE LEFT TELESCOPED
TOGETHER DURING STORAGE.
• Seam sealer has not been provided with your tent. For additional protection
we recommend seam sealing your tent prior to camping. Seam sealer may be
purchased through your local retailer or at your local sporting goods store.
• Do not leave your tent set-up for weeks at a time, be aware that
exposure to the ultraviolet rays of the sun can seriously damage material
and/or cause it to become discolored.
WARNING: KEEP ALL FLAME AND HEAT SOURCES
AWAY FROM THIS TENT FABRIC. This tent meets the
flammability requirements of CPAI-84. The fabric will burn
if left in continuous contact with any flame source. The
application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
3Raise Ends of Tent
– Insert grey shorter shock-corded
poles through pole sleeves marked
with grey binding at both ends of tent
above windows.
– Insert second pin (located near center of
tent) of pin & ring system into pole end.
– Go to opposite end of pole and
gradually apply pressure to the pole
forming an arch until you are able to
insert the pin into the pole end.
– Attach frame clips. (illus. 5)
4Attach Rainfly
– Assemble rainfly poles by
interlocking shock-corded pole.
– Insert rainfly pole into pole sleeves
located at the center edges of the
underside of rainfly. (illus. 7), (illus. 8)
– Drape rainfly over tent, pole side
down. The rainfly poles should cover
the door and rear window of tent.
– Insert rainfly poles into grommets
on tent body. (illus. 6)
– Secure rainfly with attachments
located on underside of rainfly.
– Connect the elastic loops with
“S” hooks (found at the rainfly
corners) to fabric loops near
frame clips. (illus. 8)
– Stake out guylines at the ends
of the rainfly. (illus. 10)
illus. 6 Assembled tent
without rainfly.
illus. 5
Frame clips
illus. 9
Completed tent with rainfly.
Note the guylines on each end.
Grey poles
Grommets for
rainfly poles
illus. 10
Stake out the tent with
adjustable guylines.
illus. 7 Insert rainfly
pole through pole sleeve
on underside of rainfly.
End guylines
illus. 8