Colorbeam CORLORAY DMX 50W User manual

CORLORAY DMX Driver 50W
Control Systems
User Guide
Version 1.0 December 2010
DRY

CONTENTS
1
www.colorbeam.com
1. ITEMS INCLUDED BEFORE UNPACKING.........
2. INTRODUCTION..............................................
3. SPECIFICATION..............................................
4. FUNCTION SCHEMA & INSTALLATION............
5. WIRING DIAGRAM...........................................
6. WARNING.......................................................
7. OPERATION....................................................
8. ORDER INFORMATION....................................
9. APPENDIX.......................................................
2
3
4
5
5
6
7
9
10

ITEMS INCLUDED
CD-50 Controller
Power cord
The shape of the power cord plug
varies according to country or
geographic area.
2
www.colorbeam.com
Please make sure the below items included when unpacking.
If there is anything missing please contact with your local
dealer immediately.

Features:
INTRODUCTION
www.colorbeam.com
3
USITT DMX 512-A address setting
20 built-in fixed color
9 built-in fade effect
3 channel (RGB) and 5 channel (RGB, dimmer, strobe)
Master / Slave
1.
2.
3.
4.
5.
COLORAY DMX driver 50 is a ideal power supply for Moon
Spot / Linear series with highly integrated and performance
driver. It is not only suitable with the entire Colorbeam lighting
fixture but also can be apply with any high power lighting
luminaire in the market. Impressive the 20 built-in most popular
color, 9 fading effects gives this unit more benefit.
It can be set up very easily with LED display on the fixture.
Utilizing the RJ45 connector which is widely use for architectural
installation and can be easily integrated with any lighting
systems.

Electrical
Power Voltage: 90-264VAC, 50~60Hz
Power Consumption: 50W
Fuse: F1A / 250V (5x20mm Glass Fuse Tube)
Power Output: 1 way(RJ45)*48VDC, 340±10mA
Compatible Driver: USITT DMX512-A
Communication
DMX Connecter: 3pin XLR
Output Data Connecter: RJ-45
Housing
Dimension(mm): L248 × W84 × H75
Weight: 1.5 KG
Material: Metal
Color: Black
Listing
Certifications: CE / RoHS / WEEE
Fixture Warranty: 1 Year
SPECIFICATION
4
www.colorbeam.com
8.73"
(220.0mm)
9.84"
(248.0mm)
2.86"
(72.0mm)
9.37"
(236.0mm)
0.24"
(6.0mm)
0.24"
(6.0mm)
Dia0.20"
(5.0mm)
Coloray Driver-50
OUTPU T:48 V 350mA
DMX IN DMX OUT
INPUT: AC 88-2 64 V 50/60 Hz
Coloray Driver-50
OUTPU T:48 V 350mA
DMX IN DMX OUT
INPUT: AC 88-2 64 V 50/60 Hz
Coloray Driver-50
OUTPU T:48 V 350mA
DMX IN DMX OUT
INPUT: AC 88-2 64 V 50/60 Hz
3.33"
(84.0mm)
2.98"
(75.0mm)

WIRING DIAGRAM
INSTALLATION
FUNCTION SCHEMA
1. Fix the fixture with bracket
2. Connect the AC power cord to the socket
Do not hot swap. Ensure that power to the fixture is off before connecting or
disconnecting fixtures.
CAUTION:
FUNCTION SCHEMA
INSTALLATION
Wiring Configuration
Splitter
RJ-3
Extension Connector
RJ-2
www.colorbeam.com
5
100-240VAC
50~60HZ
1x 36W output
DMX IN/OUT
Mode setting
DMX signal
Master signal
RJ 3
RJ 2
Colorbeam
Lights
Colorbeam
Lights
AC input
100~240V / 50~60Hz
AC input
100~240V / 50~60Hz
DMX OUT
DMX IN
DMX OUT
DMX IN
Connector Information
Mode No: 3-PIN XLR
1
3
2
12
3
DMX IN DMX OUT
1.GND
2.D-
3.D+
NOTICE:
1. Please notice the idea of the wiring for all Colorbeam fixture is in series connection.
2. The wiring of the customized is different from the commercially available. Please refer our
accessory RJ-2 and RJ-3 to do the extension and the split.
3. The warranty will be invalid when the fixture is not under normal usage (including trimming the cable
and do wiring by user).
Please contact with your sales representative for the detailed information if the trimming will be happen.
Controller
ORBIT TP

Read the instructions carefully before you install or powering!
2. Operation Determinations
The device must only be used indoor.
If the device has been exposed to drastic temperature fluctuation, do not switch it on
immediately. The arising condensation water might damage your device. Leave the device
switched off until it has reached room temperature.
Only operate the device after having checked the housing which is firmly closed and all
screws are tightly fastened. Do not shake the device. Avoid brute force when installing or
operating the device.
Operate the device only after having familiarized with its functions. Do not permit operation
by persons who are not qualified for operating the device. Most damages are the result of
unprofessional operation!
The maximum ambient temperature 40 degree must never be exceeded.
Please consider that unauthorized modifications on the device are forbidden due to safety
reasons!
WARNING
CAUTION!
Be careful with your operations.
You can suffer a dangerous electric shock when touch the wires inside the unit.
Keep this driver away from rain and moisture.
Unplug mains lead before opening the housing.
Make sure the plug is tightly connected with outlet.
Make sure all connector are connected properly.
Make sure the AC power that complies with local electrical codes.
Do not expose the device to heat source, corrosive, flammable or explosive area.
Do not block any of ventilation openings.
Do not open the device and try to repair the device personally.
Important
Every person involved with installation and maintenance of the this device has to :
-be qualified.
-following the instructions of manual
Please make sure that there are no obvious transport damages.
Please immediately contact the local dealers as the device is in fault operation or damage.
Damages caused by the disregard of this user manual or unauthorized modification to
products are not subject to warranty.
1. Safety Instructions
6
www.colorbeam.com
!
CAUTION!
For non-Colorbeam fixtures, refer to the
wiring diagram for installation.

OPERATION
www.colorbeam.com
7
001
C01
F01
S- Me n u
Add.
Color
Fade
Set -
Menu Up
Down
DMX No. Mode
S10
S11
S20
S21
S30
S31
S40
S41
Control all of LED fixtures in
the same channel (default)
Control all of LED fixtures
independently
Master off (default)
Master on
RGB 3 channels (default)
RGB dimming, strobe 5 channels
Delay off (default)
Delay on
Attention: It is important to read this manual before you install or
use this product.
1. Turn on / off the power
2. Fixed Color (20 colors):
There are 20 built-in fixed colors in the
device. Press Menu, the display will
show “C--” on the display. Then the user
can press Down or Up to select the
desired color from C01~C20.
3. Fade Effect ( 9 colors):
There are 9 built-in fade programs in
the device. Press Menu, the display will
show ”F--” on the display.
Then the user can press Down or
Up to select the desired fade
program from F01~F09.
The fade time of the effect can be
changed from 01~99% (0.5~50 sec).
e.g. F03 is running, the fade time
can be changed by pressing Menu
and Hold for 5 seconds. The display
will show ”S--” on the display.
The fade time can be adjusted from
01 to 99% by pressing Down and
Up, and confirm the adjustment by
pressing Menu.
4. DMX Address Setting:
Press Menu and the display shows
the initial DMX address ”001” . The
user can select the desired address
from 001~512 by pressing Down
or Up.
Note:
The function of delay on is designed
for running slow, and free-fliker
program.
The response speed of LEDs is
slower than normal. All drivers must
be set on the same mode (delay on
or off) as connecting together,
otherwise, the program does not run
synchronously.
The slave drivers must be set add.
001 when running Master / Slave
function.

8
www.colorbeam.com
6. Signal Indicator:
(1) Receive Master Signal: The green light shows when the lighting
fixture has been set as Master.
(2) Receive DMX Signal: The green light shows when the lighting fixture
is receiving DMX Signal.
7. Sleeping Mode:
The control unit will go into Sleeping Mode automatically in the event of
no instruction from the keypad after 30 sec. Under Sleeping Mode, the
control unit is functional but the display is off and the keypad is locked.
To leave the Sleeping Mode, the user can press Menu and hold for 5 sec. till
the display is on. When using the DMX Address to control the lighting fixture,
the Sleeping Mode will start after 30 sec. Press Menu and hold for 5 sec.
to leave the Sleeping Mode.
5. DMX Mode Setting:
The following mode can be selected by pressing Menu to confirm it.
Press Menu first and the display shows ”S--”. And press Down or Up
to select the desired program from S10~S41.
OPERATION

ORDER INFORMATION
ORDER INFORMATION FORM
www.colorbeam.com
9
ITEM PART NUMBER
CD-50
ITEM
Extended line
RJ-45 two-way
PART NUMBER
Splitter
Extension Connector
RJ-3
RJ-2
Spec.
2M
10M
GORC0411
POWER
ACCESSORY
5M
Spec.
1 Output / 3 Colors
D03-458002-002
D03-458010-001
B060301004
B060301005
D03-458005-001
ORBIT TP GOBC0111
CONTROLLER

APPENDIX
DMX No. R
C01
C02
C03
C04
C05
C06
C07
C08
100
0
0
100
15
0
30
100
0
100
60
0
0
80
100
0
15
100
C09
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
B
G
0
0
100
100
0
100
50
0
100
100
0
50
20
0
100
50
15
100
100
15
100
100
15
50
100400
60
100
0
30
100
100
0
1000
0
10050
100
100100
PARAMETER OF RGB
10
www.colorbeam.com

COLORBEAM CO. LTD.
314, 3F., No. 87, Minguang E. Rd.,
Taoyuan City, Taiwan 33052
TEL : [phone]
FAX : [phone]
E-MAIL : [e-mail]
W : www.colorbeam.com