Comelit Mini 6700 User manual

EN
TECHNICAL
MANUAL
Mini
art. 6701- art. 6700 Passion.Technology.Design.

2
Table of contents
Warning ............................................................................................ 2
Monitor description......................................................................... 3
Soft-touch keys description....................................................................4
Indicator LED description........................................................................4
Installation........................................................................................ 5
Removing / Fitting the terminal ..............................................................6
Fitting upgrade KIT Art. 6733W...............................................................6
Monitor configuration ..................................................................... 7
Standard configuration for soft-touch keys ..........................................7
Advanced monitor configuration ............................................................8
Warning...............................................................................................8
Programming for intercom call............................................................8
Programming/deleting intercom address
(selective intercom only) ..............................................................8
Programming buttons for intercom call .......................................9
Direct programming of intercom call .........................................10
Programming keys for generic or coded actuator ............................11
Programming buttons for other functions.........................................12
Programming range ..........................................................................13
Monitor ringtone selection ................................................................13
Programming reset ...........................................................................14
Riser addresses............................................................................. 15
Operating distances with Art. 4888C........................................... 16
Wiring diagrams with Art. 4888C ................................................. 17
System with Art. 4888C: 1 Ikall series external unit............................17
System with Art. 4888C: 2 main monitors in cascade connection ....18
System with Art. 4888C: 2 main monitors
and 1 secondary monitor in branch connection .................................18
System with Art. 4888C: 2 main monitors
and 1 secondary monitor in cascade connection...............................18
Operating distances with KIT 8461M-MB ................................... 19
Operating distances with Art. 1210.............................................. 20
Wiring diagrams with KIT 8461M-MB and Art.1210 ................... 21
KIT 8461M-MB: standard single-family system ..................................21
System with Art. 1210 ............................................................................21
KIT 8461M-MB or system with Art. 1210:
secondary monitor in branch connection............................................22
KIT 8461M-MB or system with Art. 1210:
2 additional secondary monitors in cascade connection ..................22
Floor door call connection variant............................................... 22
Warning
Intended use
This Comelit product was designed for use in the creation of audio and video communication systems in residential,
commercial or industrial settings and in public buildings or buildings used by the public.
Installation
All activities connected to the installation of Comelit products must be carried out by qualified technical personnel, with
careful observation of the indications provided in the Manuals / Instruction sheets supplied with those products.
Wires
Cut o the power supply before carrying out any maintenance procedures.
Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system
manual.
We advise against running the system wires through the same duct as the power cables (230V or higher).
Safe usage
To ensure Comelit products are used safely:
• carefully observe the indications provided in the Manuals / Instruction sheets
• make sure the system created using Comelit products has not been tampered with / damaged.
Maintenance
Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance
with the indications provided in the Manuals / Instruction sheets.
Any repair work must be carried out
• for the products themselves, exclusively by Comelit Group S.p.A.,
• for systems, by qualified technical personnel.
Disclaimer
Comelit Group S.p.A. does not assume any responsibility for
• any usage other than the intended use
• non-observance of the indications and warnings contained in this Manual / Instruction sheet.
Comelit Group S.p.A. nonetheless reserves the right to change the information provided in this Manual / Instruction
sheet at any time and without prior notice.

3
Monitor description
1
2
3
5
4
6
12
7
8
10
11
12
9
LL CFP1 CFP2
1. Brightness control
fTo increase the value, turn clockwise
2. Colour intensity adjustment for Art. 6701
Contrast adjustment for B/W monitor Art. 6700
fTo increase the value, turn clockwise
3. 4.3’’ LCD screen (in colour for Art. 6701, B/W for Art. 6700)
4. Call volume adjustment (high - medium - low)
5. Soft-touch keys
6. Monitor handset (lift handset to start communication)
7. S1 User code programming microswitches (see table on page. 15)
8. S2 Button and function programming microswitches (marked with a red corner)
DIP 1-2-3-4 for button function programming
DIP 5-6 access to programming
DIP 7 for power supply voltage management (see diagrams and variants on page 17), default = OFF
9. Loudspeaker volume adjustment (for setting intercom audio only)
10. CV5 Video closing jumper
11. Pin for securing terminal block
12. Space for housing the operation accessory for keys (standard on all black monitors, available to purchase
separately for white monitors Art. 6733W)
Terminal block for system connection
LL Bus line connection terminals
CFP1 CFP2 Floor door call input
For systems with 2-wire KIT or Art. 1210, set DIP 7 to ON.
A maximum of 1 main monitor can be set in systems with 2-WIRE KIT or Art. 1210, and 2 main monitors in systems
with Art. 4888C.
DIP 8:
ON secondary monitor
OFF main monitor (default)

4
Soft-touch keys description
Indicator LED description
fPress the desired key once to activate the function associated with it
Lock-release LED
slow flashing: door open;
1 flash after pressing: door opening confirmation;
continuous flashing: call in progress.
Privacy LED (red)
steady: privacy function enabled
3 flashes (every 5 sec.): doctor function enabled
continuous flashing: device in programming mode
4 flashes: system engaged
Lock-release key
Key 1 Actuator function (programmable)
Key 2 Self-ignition function (programmable)
Privacy key
Keys (programmable) present as standard on all black monitors (for white monitors the KIT with additional buttons Art.
6733W is available to purchase separately)
Wait for approximately 1 sec. before pressing the same key again. Pressing the same key several times in quick
succession will cancel the command.
The monitor Art. 3701/6700 is designed for use in colour systems, in the SB2 section downstream of Art. 4888C, or
in systems without mixer, such as the system with 2-wire KIT or Art. 1210.

5
Installation
optional
fixing
16,0 cm
17,5 cm
1C1B1A
4
32
2
1
6 7
1
3
2
CLACK!
CLACK!
CLACK!
5

6
Removing / Fitting the terminal
3
1
2
L L C
F
P
1C
F
P
2
1
2
3
1
1
2
2
1
(to remove)
6
54
1
3
2
CLACK!
CLACK!
CLACK!
2
1
2
2
11
8 97
LL CFP1 CFP2
2
3
1
2
1
3
21
Fitting upgrade KIT Art. 6733W

7
Standard configuration for DIP switches 1-2-3-4
Monitor configuration
Standard configuration for soft-touch keys
DIP S2 Art. (6700W / 6700W/BM / 6701W / 6701W/BM ) + Art. 6733W /
Art. 6701B / 6701B/BM
DIP 1 DIP 2 DIP 3 DIP 4 P1 P2 P3 P4 P5 P6
0000ACT AI CCS D PAN K
1000CCS AI INT INTb D ACT
0100INT AI INTb ACT CCS CCP
1100ACT CCS CCP PAN K D
0010ACT ACT ACT ACT ACT ACT ACT
1010INT ACT CCS CCP INTb PAN
0110AI D K CCS CCP INTb
1110INTb INT AI INT PAN D
0001CCS PAN D AI INT INTb
1001 K CCS PAN CCP AI INT
0101CCP K PAN ACT INT AI
1101PAN CCP CCS K ACT D
0011INTb AI INT ACT D CCS
1011INT INT INT INT INT INT
0111NULL NULL NULL NULL NULL NULL NULL
1111 PROG
Legend
Lock- release
ACT Actuator
AI Self-ignition
CCP Main switchboard call – not for use in systems with KIT
CCS Secondary switchboard call – not for use in systems with KIT
K Guardian doorentry phone call
D Doctor
PAN Panic – not for use in systems with KIT
INT Programmable intercom, general or selective - standard singlefamily calling for KIT and Simplebus Top
INTb Two-family intercom - for KIT only
NULL No function
PROG
Programmed functions, see pages 8-12.
In this Dip switch setting, the buttons control the programmed functions; the NON-programmed buttons
control functions referred to on line 0000 (default).

8
If the default settings (see table on page 7) do not reflect requirements, the keys can be programmed dierently by carrying
out the steps below.
At the end, set S2 DIP switches 1-2-3-4 to the combination 1111 (PROG setting in the configuration tables on pages
8-12). In this dip switch setting, the keys control the programmed functions; the NON-programmed keys control
functions referred to on line 0000 (see table on page 7). Restore the user code setting on S1, see table A on page 15.
Warning
Programming/deleting intercom address (selective intercom only)
Selective intercom addresses
You must set the intercom address on all the riser’s internal units.
You can assign the same intercom address to a maximum of 3 internal units.
For group calls, select the desired intercom codes simultaneously (max. 3).
Advanced monitor configuration
Programming for intercom call
General intercom: function allowing calls to one or more internal units identified by the same call address as used
by the external unit.
Selective intercom: function allowing calls to one or more internal units identified by a dedicated call address (see
table B, page 8) which is different from the one used by the external unit.
General and selective intercoms CANNOT be used together on the same riser.
Take note of the S2, S1 setting and restore it when programming is complete
1) 2) 3)
Programming; set code,
TAB. B on page 8
S1
S2 DIP
1 2 3 4 5 6
000111
S2
Cancellation
DIP OFF
DIP ON
S1
S2 DIP
1 2 3 4 5 6
111111
S2
TAB. B
Code Dip switch ON S1 Code Dip switch ON S1
1 1 5 5
2 2 6 6
3 3 7 7
4 4 8 8

9
Example 1 - all systems (INCLUDING KITS!) - General intercom
on a monitor with user code 5, P3 programming = general internal call, P4 = general intercom with address 9
Example 2 - Selective intercom
on a monitor with user code 1 and intercom address 1, P3 programming = selective intercom with address 2, P4 = selective
intercom with address 3
1. Set S2 DIP switch 6 to the combination 01.
»the privacy LED flashes.
S2 DIP
1 2 3 4 5 6
000001
S2
2. Refer to the table on page 9and select a combination in which the intercom function (either INT or INTb) is listed for the
keys you wish to program.
E.g. 1: for P3= general internal call, set S2 DIP switches 1-2-3-4 to the combination 1000 or 0011 or 1011 (P3=INT), set S1
with address 5 in accordance with table A on page 15, go to point 3.
E.g. 1: for P4= general intercom, set S2 DIP switches 1-2-3-4 to the combination 1110 or 1011 (P4=INT), set S1 with
address 9 in accordance with table A on page 15, go to point 3.
E.g. 2: for P3= single-family intercom, set S2 DIP switches 1-2-3-4 to the combination 1000 or 0011 or 1011 (P3=INT), set
S1 with address 2 in accordance with table B on page 8, go to point 3.
E.g. 2: for P4= selective intercom, set S2 DIP switches 1-2-3-4 to the combination 1110 or 1011 (P4=INT), set S1 with
address 3 in accordance with table B on page 8, go to point 3.
3. Press and release the key to be associated with the function
»the lock-release LED lights up.
»a confirmation tone will sound.
4. To exit programming mode, set S2 DIP switches 5-6 to the combination 00
fthe privacy LED switches o
5. When programming is complete, set S2 DIP switches 1-2-3-4 to the combination 1111. Restore the user code
setting on S1, see table A on page 15.
Programming buttons for intercom call
DIP S2 Art. (6700W / 6700W/BM / 6701W / 6701W/BM ) +
Art. 6733W Art. 6701B / 6701B/BM DIP S1
DIP 1 DIP 2 DIP 3 DIP 4 P1 P2 P3 P4 P5 P6
ADDRESS
0 0 0 0
1 0 0 0 INT INTb
0 1 0 0 INT INTb
1 1 0 0
0 0 1 0
1 0 1 0 INT INTb
0 1 1 0 INTb
1 1 1 0 INTb INT INT
0 0 0 1 INT INTb
1 0 0 1 INT
0 1 0 1 INT
1 1 0 1
0 0 1 1 INTb INT
1 0 1 1 INT INT INT INT INT INT
0 1 1 1
1 1 1 1 PROG

10
Direct programming of intercom call
NOTE If a call is received during programming, it must be answered and the programming procedure resumed
afterwards.
Allows direct programming of intercom call via the internal units.
√Requires 2 operators
Step 1: enter programming mode
Operator 1 and Operator 2 carry out the following procedures on 2 internal units:
1. Set S2 DIP switches 1-2 -3-4 to the combination 1111
2. Lift the handset
3. Press and hold the privacy and lock-release keys for 3 sec.
»The internal unit emits 1 tone.
»The privacy LED flashes.
»The internal unit enters audio mode.
»At this point the 2 operators will be communicating with each other.
Step 2: intercom call programming
Operator 1:
fPress the key you want to program to call operator 2 (e.g. 2).
»The internal unit manned by operator 1 emits a confirmation tone.
Operator 2:
fPress the key you want to program to call operator 1 (e.g. 1).
»The internal unit manned by operator 2 emits a confirmation tone.
Operator 1/ Operator 2:
fHang up the handset.
»The internal unit emits 1 tone.
»Programming of the 2 internal units is now complete.
To program another internal unit, move on to STEP 3.
Step 3: programming other internal units
Operator 1/ Operator 2:
1. Once the new station has been reached, carry out step 1 to begin communication
2. Repeat step 2