Comelit Simplebus2 Ultra UT2010 User manual

Passion.Technology.Design.
EN
Simplebus2 Ultra audio module
Art. UT2010
TECHNICAL
MANUAL

2
Warning
Intended use
This Comelit product has been designed and manufactured for use in the creation of audio and video communication
systems in residential, commercial, industrial and public buildings.
Installation
All activities connected to the installation of Comelit products must be carried out by qualified technical personnel,
with careful observation of the indications provided in the Manuals / Instruction sheets supplied with those products.
Wires
Disconnect the power supply before carrying out any operations on the wiring.
Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system
manual.
We advise against running the system wires through the same duct as power cables (230V or higher).
Safe usage
To ensure Comelit products are used safely:
• carefully observe the indications provided in the Manuals / Instruction sheets,
• make sure the system created using Comelit products has not been tampered with / damaged.
Service
Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance
with the indications provided in the Manuals / Instruction sheets.
Any repairs must be carried out:
• for the products themselves, exclusively by Comelit Group S.p.A.,
• for the systems, by qualified technical personnel.
Disclaimer
Comelit Group S.p.A. does not assume any responsibility for
• any purpose other than the intended use,
• failure to observe the indications and warnings contained in this Manual / Instruction sheet.
Comelit Group S.p.A. reserves the right to change the information provided in this Manual / Instruction Sheet at any
time and without prior notice.

3
Table of contents
Warning ............................................................................................ 2
Description....................................................................................... 4
UT2010 ......................................................................................................4
Technical specifications ................................................................. 6
Art. UT2010 ...............................................................................................6
Installation........................................................................................ 7
Flush-mounted installation composition table....................................7
Surface-mounted installation composition table................................7
Flush-mounted installation............................................................. 8
Removing nameplates (2A) / module (2B)..............................................9
Installation with side-by-side boxes.....................................................10
Wall-mounted installation............................................................. 11
Optional .......................................................................................... 11
Removing nameplates (2A) / module (2B)............................................12
Installation with side-by-side boxes.....................................................13
Connections................................................................................... 14
UT2010 connections ..............................................................................14
UT2010 connections with separate power supply..............................14
Variants ...................................................................................................14
Module connection........................................................................ 15
Outdoor entrance panel module consumption table..........................15
powered by Art. 1210/1210A............................................................15
powered by additional power supply unit Art. 1595.........................15
Connection of button modules Art. UT9200.....................................16
Connection of Touchscreen module Art. UT9270.............................16
Connection of number keypad module Art. UT9279M.....................16
Variant with separate power supply..................................................16
Programming ................................................................................. 17
Configuring the button type to maintain during normal operation
(single/dual) ............................................................................................17
Address button modules .......................................................................17
Program call addresses.........................................................................17
Smart programming of consecutive addresses ......................... 18
Programming of specific addresses............................................ 19
Special programming via DIP Switch .......................................... 20
Special programming table...................................................................21
Twilight sensor............................................................................... 23
Button backlighting management ........................................................23
Checking twilight sensor operation .....................................................24
Adjusting the brightness of the button LEDs ......................................25
Light-me function .......................................................................... 26
Light-me function behaviour on the basis of the LED backlighting
mode........................................................................................................26
Replacing the audio module with programming restore backup27
Configuring via PC......................................................................... 28
Errors and indications................................................................... 28
System performance and layouts ................................................ 28
Addressing table............................................................................ 29

4
UT2010
Audio module for Ultra entrance panel, Simplebus2 system. For use in systems with power supply unit art. 1210 /
1210A.
Easy to install and simple to configure, thanks to the smart programming of call buttons.
Twilight sensor for automatic nameplate backlighting switch-off during daylight hours.
Omnidirectional digital microphone and double loudspeaker for high-fidelity audio.
Audio-visual indications for disabled individuals assistance request can be activated via programming.
Facility for 2 call buttons. To be finished with cap, single button or dual button made using aluminium or professional
grade plastic treated to prevent yellowing and dulling.
Adjustment and programming can take place without removing the module.
Dimensions: 100 x 90 x 35 mm.
ULTRA: the new and most technologically advanced entrance panel offering maximum ease of installation.
Available in flush-mounted (10 mm protrusion from the wall) or surface-mounted (just 35 mm protrusion from the wall)
variants.
Description

5
UP
13. 14. 15.3. 4. 5. 6.
9.10.11. 12. 8.
1.
7. 16.
17.
2.
1
2
1. Indicator LEDs
call sent (green) / system busy (red)
lock-release enabled
communication enabled
2. Loudspeakers
3. Speaker volume control
4. S1 Button programming selector
5. S2 Special programming selector
6. Micro USB input for programming via computer
7. Jumper for power supply management (remove in case of
separate power supply)
8. Twilight sensor
9. Addressing and programming Dip Switches
10. Microphone volume control
11. Programming confirmation button
12. Digital microphone
Use screwdriver supplied
13. Terminal block for connection:
RTE programmable RTE (local lock-release
input) or DO input (door open indication)
GND SE- RTE and door lock input reference
negative
SE+ electric door lock connection
NO NC COM relay contacts
V- V+ power supply
LL bus line connection
14. Ethernet terminal block, only for use in case of additional
modules with LAN
15. Connector for additional modules with LAN
16. 17. Connector for additional module connection

6
Technical specifications
Art. UT2010
GENERAL DATA
Type Modular
Product height (mm) 90
Product width (mm) 100
Product depth (mm) 35
Product colour Black RAL9005, Transparent, Aluminium
Product weight (g) 275
Coating material type Polycarbonate, Aluminium alloy
Flush mounting Yes, with specific accessory
Surface mounting Yes, with specific accessory
COMPATIBLE SYSTEMS
Simplebus 2 audio/video with
power supply unit art. 1210/1210A Yes
Simplebus 2 audio/video kit with
power supply unit art. 1209 Yes
Simplebus 2 audio with
power supply unit art. 1210/1210A Yes
AUDIO SPECIFICATIONS
Microphone MEMS digital audio sensor, omnidirectional
Loudspeaker 28 mm (Ø), 8 Ohm, 1W (2)
Technologies implemented Full-Duplex
ELECTRICAL SPECIFICATIONS
Type of power supply Power supply via video entry bus
Power supply voltage 33 VDC
Absorption in standby (W) 1.5
Maximum absorption (W) 3.5
HARDWARE CHARACTERISTICS
Call type Buttons
Type of buttons Mechanical
Number of buttons (no.) 2
Backlighting colour White, O
Terminals L L V+ V- COM NC NO SE+ SE-/GND RTE TX- TX+ RX- RX+
Number of inputs (no.) 1
Number of outputs (no.) 2
Output type Micro-USB
Communication port Relay (C-NO-NC, 4A@12-24 VAC/VDC, inrush current 10A)
Twilight sensor Ye s
SETTINGS
Loudspeaker volume Yes
Mic volume Yes
Backlighting brightness Yes
PROGRAMMING MODE
Manual (by means of Dip Switch) Yes
ViP Manager software Yes
ENVIRONMENTAL AND CONFORMITY
SPECIFICATIONS
IP protection rating (when installed) IP65
IK anti-vandal protection rating IK08
Operating temperature (°C) -25 to 55
Operating humidity (max RH - %) 25 to 95
Environmental class IV
Conformity and Certifications RoHS II - 2011/65/EU (EN 50581:2012), EMC 2014/30/EU (EN 61000-6-
1:2007, EN 61000-6-3:2007+A1:2011)
MAIN FUNCTIONS
Lock-release Yes
Number of auxiliary relays (no.) 1
Input for local key button Yes
Input for door open signal Yes
System status visual indications Yes
System status audio indications Yes
System status voice synthesis Yes

7
Installation
Flush-mounted box
3110/1
3110/1A
3110/2
3110/2A
3110/3
3110/3A
3110/4
3110/4A
Rain shield
UT9181 UT9182 UT9184H UT9183 UT9186 UT9189 UT9184 UT9188
Module holder/ finishing frame
UT9161 UT9162 UT9163 UT9164
Rain shield UT9191 UT9192 UT9194H UT9193 UT9196 UT9199 UT9194 UT9198
Housing/frame UT9171 UT9172 UT9174H UT9173 UT9176 UT9179 UT9174 UT9178
Optional
The entrance panel is available in flush-mounted or surface-mounted variants:
Flush-mounted installation composition table
Surface-mounted installation composition table
A = Rain shield
B = Surface-mounted housing with frame
A = Flush-mounted box
B = Rain shield
C = Flush-mounted module holder with finishing frame

8
2
1
2
UP
53 4
165 cm
130 cm
1
Flush-mounted installation
BLACK
RED
Optional
Optional

9
6
1
A
B
C
C
2
+ Art. UT9110
MAX 0,2 mm
MAX 0,2 mm
9
1
2
10 12
2
1
11
CLACK!
CLACK!
1
2
3CLACK!
8
CLACK!
CLACK!
CLACK!
1
2
3
7
1
2
3
1
2
3
1
2A
1
3
2
4
2B
Kit Art. UT9110 contains 5 sheets of pre-cut labels for nameplates and 1 sheet for the information module.
The sheets are made using Yupo paper which oers the ultimate transparency and resistance to atmospheric agents over time.
To print the labels, use the editable .pdf file which is available to download free of charge from the website pro.comelitgroup.com
The button has a nameplate which can be written on (A);
alternatively, an adhesive label can be applied (B).
The total thickness of the nameplate + adhesive label
must not exceed 0.2 mm.
You can visit the website pro.comelitgroup.com to download
the PDF to print the entrance panel name cards, using the
adhesive pre-cut sheets (C) available in our catalogue (Art.
UT9110 ).
Custom engraved Full Metal Ultra nameplates are available
on request. Find out how:
https://pro.comelitgroup.com/
customised-nameplates-for-ultra-entrance-panel
Removing nameplates (2A) / module (2B)
CLOSE

10
Installation with side-by-side boxes
Before installing the boxes in the wall, fit the spacers.

11
165 cm
130 cm
2
UP
53 4
UP
1
2
3
1
Wall-mounted installation
Optional
BLACK
RED
Optional

12
6
1
A
B
C
C
2
+ Art. UT9110
MAX 0,2 mm
MAX 0,2 mm
9
1
2
10
2
1
11 12
CLACK!
CLACK!
1
2
CLACK!
3
8
CLACK!
CLACK!
1
2
CLACK!
3
7
1
2
3
1
2
1
3
2A
1
3
2
4
2B
Removing nameplates (2A) / module (2B)
CLOSE
The button has a nameplate which can be written on (A);
alternatively, an adhesive label can be applied (B).
The total thickness of the nameplate + adhesive label
must not exceed 0.2 mm.
You can visit the website pro.comelitgroup.com to download
the PDF to print the entrance panel name cards, using the
adhesive pre-cut sheets (C) available in our catalogue (Art.
UT9110 ).
Custom engraved Full Metal Ultra nameplates are available
on request. Find out how:
https://pro.comelitgroup.com/
customised-nameplates-for-ultra-entrance-panel
Kit Art. UT9110 contains 5 sheets of pre-cut labels for nameplates and 1 sheet for the information module.
The sheets are made using Yupo paper which oers the ultimate transparency and resistance to atmospheric agents over time.
To print the labels, use the editable .pdf file which is available to download free of charge from the website pro.comelitgroup.com

13
Installation with side-by-side boxes

14
1210A
1210
UT2010
E
T
R
GND
SE
-SE
+
NO NC
C
O
M
LL
+
VV
-
-
+
120-230 V
1595
1210A
1210
E
T
R
GND
SE
-
SE
+
NO NC
C
O
M
LL
+
VV
-
J4
J4
UT2010
E
T
R
GND
SE
-
SE
+
NO NC
C
O
M
LL
+
VV
-
1210A
1210
10A MAX
AC-DC
12V/24V
10A MAX
AC-DC
12V/24V
E
T
R
GND
SE
-
SE
+
NO NC
C
O
M
LL
+
VV
-
1210A
1210
ON
1 2 3 4 6 75 8
UT2010
UT2010
Connections
UT2010 connections
UT2010 connections with separate power supply
Max 20 m. Local door-opener button.
Max 20 m. Local door-opener button.
“C.NC.NO relay activation on actuator command: 2 sec”
fSet DIP switch 8 to ON permanently
(as shown in the figure)
Max 20 m. Local door-opener button.
Variants
Variant for using the outdoor entrance panel relay Variant for using a safety door lock

15
UP
LL
UP
LL
V+V-
J4
Module connection
On systems with Art. UT2010 and power supply unit Art. 1210/1210A, the maximum current available for the
outdoor entrance panel modules is 100 mA.
Calculate the total power consumption of the modules in your system configuration using the Consumption
table.
If the total power consumption exceeds 100 mA, connect a supplementary power supply unit (Art. 1595)
to the V+ and V- contacts of the outdoor entrance panel, as shown in the figure below (see “UT2010
connections with separate power supply”). In any case, the total absorption must be lower than 500 mA.
Outdoor entrance panel module consumption table
Code Consumption (mA)
UT9200 Call button modules 12.5
UT9240 Information module 12.5
UT9240M Metal information module 12.5
UT9279M Number keypad module
40 Relays disabled and audio or audio/
video module SE output used
75 With 1 bistable relay active
100 With 2 bistable relays active at the same
time
UT9310M Magnetic induction module 245 Always needs to be powered by
additional power supply unit Art. 1595
UT9270 Touchscreen module 100
In systems with an outdoor entrance
panel consisting of 1 audio or audio/
video module, Touch module art.
UT9270 and up to 80 users, it is not
necessary to provide any additional
power supply.
For all other combinations, provide an
additional power supply unit art. 1595
powered by Art. 1210/1210A
A B powered by additional power supply unit Art. 1595

16
UP
BLACK
RED
MAX 8
1210A
1210
UT9200
E
T
R
GND
SE
-SE
+
NO NC
C
O
M
LL
+
VV
-
UT2010
1210A
1210
UT9270
E
T
R
GND
SE
-SE
+
NO NC
C
O
M
LL
+
VV
-
1210A
1210
E
T
R
GND
SE
-SE
+
NO NC
C
O
M
LL
+
VV
-
J4
UT9270
Maximum
80 users > 8O users
UT2010 UT2010
-
+
120-230 V
1595
1210A
1210
UT9279M
E
T
R
GND
SE
-SE
+
NO NC
C
O
M
LL
+
VV
-
UT2010
Connection of button modules Art. UT9200
Connection of Touchscreen module Art. UT9270 Variant with separate power supply
Connection of number keypad module Art. UT9279M
Max 20 m. Local door-opener button.
Max 8 modules (Max 30 modules with additional power supply).
Max 20 m. Local door-opener button.
For systems with over 80 users, provide an additional power supply
Max 20 m. Local door-opener button.

17
65
default
65
ON
OFF
1
ON
2 3 4 65
8765 8765
default
ON
OFF
1
ON
2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
1
2
4
3
5
Programming
For correct programming, follow the instructions below in order
I. Configure button type
II. Address button modules
III. Program call addresses
code DIP ON
1112 3.4 23 1,2,3,5
2213 1,3,4 24 4.5
31.2 14 2,3,4 25 1,4,5
4315 1,2,3,4 26 2,4,5
51.3 16 527 1,2,4,5
62.3 17 1.5 28 3,4,5
71,2,3 18 2.5 29 1,3,4,5
8419 1,2,5 30 2,3,4,5
91.4 20 3.5 31 1,2,3,4,5
10 2.4 21 1,3,5
11 1,2,4 22 2,3,5
TAB. A
Configuring the button type to maintain during normal operation (single/dual)
DIP 6: configuring button type:
Single button (DIP6 ON).
Dual button (DIP6 OFF, default).
I
Address button modules
DIP 1-5: addressing call button module (see TAB. A)
Addressing call button modules means that, in the event they are replaced, it is not necessary to reprogram the
button addresses. All you need to do is assign the same address as before to the new module.
II
Program call addresses
There are 2 programming methods:
• Smart programming of consecutive addresses: allows quick programming of buttons with consecutive addresses
(e.g.: 1, 2, 3, 4)
• Programming of specific addresses: allows programming of specific addresses (e.g.: 25, 37, 70, 58)
III
DIP 6: configuring button type:
Single button (DIP6 ON).
Dual button (DIP6 OFF, default).

18
Smart programming of consecutive addresses
LL
1
S1 S2
8
8765
default
OFF
8765
ON
9
DIP 6: configuring
button type:
Single button (DIP6
ON).
Dual button (DIP6
OFF, default).
OFF
ON
1 2 3 4 6 75 8
4
S1 S2
3
ON
1 2 3 4 6 75 8
5
example:
code 1
Set the address of the apartment you
wish to call (for example:1) using the
DIP-switches
(see “Addressing table” )
8765
default
OFF
8765
ON
2
DIP 6: configuring
button type:
Single button (DIP6
ON).
Dual button (DIP6
OFF, default).
=1
6
= 2
+1
= 3
+1 = 4 +1
= 5
+1
7
Press the button you want to
associate with the call address set
using the DIP-switches
Press the following buttons
to assign consecutive addresses.

19
LL
1
8765
default
OFF
8765
ON
2
DIP 6: configuring
button type:
Single button (DIP6
ON).
Dual button (DIP6
OFF, default).
OFF
ON
1 2 3 4 6 75 8
4
S1 S2
3
ON
1 2 3 4 6 75 8
5
example:
code 25
Set the address of the apartment you
wish to call (for example:25) using
the DIP-switches
(see “Addressing table” )
S1 S2
8
8765
default
OFF
8765
ON
9
DIP 6: configuring
button type:
Single button (DIP6
ON).
Dual button (DIP6
OFF, default).
=25
6
ON
1 2 3 4 6 75 8
ON
1 2 3 4 6 75 8
ON
1 2 3 4 6 75 8
37
70 58
7
Press the button you want to
associate with the call address set
using the DIP-switches
Repeat steps 4 and 5 to assign a specific address to each button
example: code 37 example: code 70 example: code 58
Programming of specific addresses

20
OFF
ON
1 2 3 4 6 75 8
2
1
4 5
1. Set the dip switches
in accordance with
the function you
wish to program
(see “Special
programming
table”).
2. Press the confirm
button.
7
Reset the configuration of the
DIP-switches
S1 S2
6
LL
1 2
Take note of the DIP-switch
settings
S1 S2
3
Special programming via DIP Switch