COMHARBOR MX286961AAA User manual

1
Living Flame Gas Patio Heater in S
Assemble Instruction
Model Number: PH08-A
WAR
Read this instruction be
appliance must be inst
instructions and local
appliance in enclosed a
PROHIBITED.
• Do the leak test after e
• Never check for leaks
• Do not store or use
vapors and liquids in t
IF YO
• Close the valve of the
• Extinguish all naked
electrical appliances
• Check for leaks as deta
• If odor persists, conta
immediately
FOR OUTDOOR USE ONLY.
Model: MX286961AAA
USER’S MANUAL
Pyramid Outdoor Patio Heater

1
PLEASE KEEP THIS INSTRUCTION FOR FUTURE REFERENCE.
WARNlNG SAFETY RULES
PLEASE READ THE FOLLOWING SAFETY RULES PRlOR TO OPERATION OF THE HEATER
WARNING
• Do not leave a heating appliance unattended, especially if children or pets are also present.
• Gas or petroleum heating appliances require adequate ventilation. So don’t close all the
cracks. Otherwise there is a risk of CO poisoning.
• Be careful with heating appliances, do not put anything on them and place them at a
• Only use electrical appliances with a safe cord.
• Completely turn off devices you are not using, especially when you are sleeping or not at
home.
•
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2.
3.
FOR YOUR SAFETY
•
any other appliance.
• An LP cylinder not connected for use shall not be stored in the vicinity of this or any other
appliance.
• Do the leak test after each changing LPG cylinder.
•
• ds in the vicinity of this appliance.
READ THE INSTRUCTIONS BEFORE INSTALLATION AND USE
• Improper installation, adjustment, alteration, service or maintenance can cause injury or
property damage. Read the installation, operating and maintenance instructions thoroughly
before installing or servicing this equipment.
• This appliance must be installed and the gas cylinder stored in accordance with the regulati
ons in force.
• Do not obstruct the ventilation holes of the cylinder housing.
• Do not move the appliance when in operation.
• Shut off the valve at the gas cylinder or the regulator before moving the appliance.
•
•
• In case of violent wind particular attention must be taken against tilting of the appliance.
FOR OUTDOOR USE ONLY.
DO NOT USE THE HEATER WHEN IT IS RAINING AND DO NOT LET ANY LIQUID COME INTO CONTACT
WITH THE GLASS TUBE WHEN THE HEATER IS IN USE.
Living Flame Gas Patio Heater in Stainless Steel
WARNING
Read this instruction before using this appliance. The
appliance must be installed in accordance with the
cal regulations. The use of this
appliance in enclosed areas can be dangerous and is
eak test after each changing LPG cylinder.
• Never check for leaks with a match or open flame
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this appliance.
IF YOU SMELL GAS
Close the valve of the gas cylinder or regulator.
• Extinguish all naked flames; do not operate any
• Check for leaks as detailed in this instructions
• If odor persists, contact your dealer or gas supplier

2
PRECAUTIONS
•
• Do not use the heater in an explosive atmosphere.
• Before use, check the hose.
• Do not attempt to alter any parts of the heater.
Example:
• Never replace or substitute the regulator, use only supplied regulator which is suitable both
appliance category and normal pressure of gas.
•
• The LPG gas cylinder valve should be turned off when the heater is not in use.
• Keep the children away from the heater. Adult supervision must be given at all times.
• Do not move the appliance when in operation.
• Check the heater immediately if any of the following exists:
1. There is smell of gas.
2. The heater is not effective.
3. The burner makes popping noise during use (a slight popping noise is normal when the burner
is extinguished after use).
• If you smell gas, turn off the valve immediately. If smell persists, contact the manufacturer
immediately.
• The hose with regulator assembly should be stored in a safety place to avoid accidental
damage.
• Children and adults should be aware of the high surface temperature hazard, and should stay
at a safe distance
• Young children should be carefully supervised
•
the heater.
•
• Keep the ventilation opening of the cylinder enclosure free and clear of debris.
• Do not obstruct the ventilation holes of the cylinder housing.
• Shut off the valve of gas cylinder or the regulator before moving the appliance.
•
•
• In case of violent wind particular attention must be taken against tilting of the appliance.
APPLIANCE STAND AND LOACTION
• The appliance is for outdoor use only. Do not use it for indoor
or in an enclosed area.
• Always maintain proper clearance from combustible materials,
i.e. top 80 cm and sides 65 cm minimum.
ND AND LOACTION
o not use
mbustible
minimum.
TEST
he installation site. Please follow the procedure

3
LEAKAGE TEST
A gas leakage test must be performed again at the installation site. Please follow the procedure
below for leakage test.
• Make a soap solution of one part liquid detergent and one part water. The soap solution can be
applied with spray bottle, brush or rag. Soap bubbles will appear where a leak is present.
• Make sure the control tap is in the “OFF” position (full disk = ●) on the control panel.
• Turn on the gas supply and check for bubbles from the hoses and connections. If a bubble is
viable this means that a leak path is present.
•
turn gas again and recheck.
• Never leak test whist smoking.
INSTALLATION
Important safety requirements:
THIS APPLIANCE IS FOR OUTDOOR USE ONLY
1. This appliance shall not be installed or used indoors, in buildings, garages or any other enclosed
area.
2. DO NOT place articles on or against this appliance.
3.
4.
place.
5.
cleaning may be required as necessary. It is imperative that control compartment, burners and
circulating air passages of the heater and light be kept clean.

4
Part NO. QTY PICTURE REMARKSPART NAME
1
2
3
4
5
6
7
8
9
10
1
1
1
4
4
1
1
1
1
1
Middle plate
Control box
Bottom plate
Lower
support
Upper
support
Upper plate
Plate cover
Glass tube
Damper Pre-assembled in
the upper plate
Pre-assembled in
the middle plate
PARTS LIST 1

5
Part NO. QTY PICTURE REMARKSPART NAME
11
12
14
15
16
17
18
19
20
21
4
1
4
3
1
66
1
1
1
1
Lower protection
guard
Handle
Connecting
tube
Fixing
bracket
Side panel
Front panel
Screw M3/16’’
Handle
Chain
AA battery
Wheels
Optional part
Pre-assembled
with Handle
connecting tube
All preassembled
in relative parts
PARTS LIST 2
INJECTOR

6
HEATER ASSEMBLY
Tools Required:
1 Screwdriver, 1 adjustable spanner
1. Unscrew the pre-assembled screws
supports(4) to bottom plate (3) and
middle plate (1) using the unscrew
screws (17).
3. Unscrew (M3/16) 4pcs screws from the
bottom of the middle plate (1). Install a
AA battery (20) into the control box, then
the middle plate(1) using screws (17).
4. Carefully put the glass tube (8) up through
the centre hole in the upper plate (6), make
sure the rubber ring is attached on the lower
end of the glass tube (8). Move and sit the
glass tube(8) through the hole of the plate
cover (7) on the middle plate (1), check and
ensure that the glass tube (8) cover the
centre hole of the middle plate (1)
2. Unscrew the pre-assembled screws (M3/16 ).
Connect 4 upper supports (5) to the lower
supports (4) and secure using screws (17).
Fix the upper plate (6) to 4 upper supports (5)
using screws (17).

7
5.
using screws (17).
7. Assemble the wheels on the base with
M6X12 screws x 4pcs and M6 nuts x 4pcs
(pre-assembled on the wheels).
8. Fix 3 side panels (15) by
the screw (17).
Note:Don’t cove the side
where the control knob is.
6. Attach the protection guards (11) onto
the frame by putting the hooks into the
holes of the frame. Fix the guards by

8
OPERATION
You need a suitable
size LPG cylinder that can be installed to the compartment.
You have to use pressure regulator with an outlet pressure
with the appliance category. The flexible tube must be
Connect the hose to the hose connector in the control box
Always test the hose for leaks with soapy water at both of the
ining, if the glass tube is suddenly met with water it may
Never splash any liquid to the glass tube when the heater is in operation
hot when it is working, do not try to touch it
the glass tube may break if the heater was to fall
is damaged
9. Screw the handle(18) onto the front panel (16), attached the handle connector tube (12) back
the front panel, screw them with 2pcs M4X8 bolts, hook the chain (19) to the hole in control box,
then Close panel to the middle plate, the panel is attracted by the magnets.
Tips: the chain can hold the panel while operating the control
COMPLETED
OPERATION
Preparation:
You will need to purchase a LPG cylinder. You need a suitable size LPG cylinder that can be
installed to the compartment.
You have to use pressure regulator with an outlet pressure comply with the appliance category.
Connect the hose to the hose connector in the control box.
Warning:
Always test the hose for leaks with soapy water at both of the ends.
Warning:
• Never use the heater while it is raining, if the glass tube is suddenly met with water it may break.
• Never splash any liquid to the glass tube when the heater is in operation
• The glass tube will be extremely hot when it is working, do not try to touch it
• Keep the children away from the heater.
•
• Never use the heater if the glass tube is damaged.

9
10
Never splash any liquid to the glass tube when the heater is in operation
The glass tube will be extremely hot when it is working, do not try to touch it
Keep the children away from the heater.
Always ensure the heater stands firmly; the glass tube may break if the heater was to fall
Never use the heater if the glass tube is damaged
LIGHTING INSTRUCTIONS
Check and ensure that an AA
battery is inside the ignition
chamber and has power. Ensure the
anode(+) faces outside.
1. Ensure that the control knob is OFF. Slowly open the gas
cylinder valve.
2. Press and turn the control knob to LIGHTposition, push the
igniter to generate spark while keeping control knob in pressed
position
3. Check for pilot flame through glass tube. If pilot does not light,
turn control knob to ‘OFF’ position wait two minutes
minimum and try again from the start. Some attempts may be
necessary.
4. If the pilot alight, keep control knob pressed for 15 seconds
then turn the control knob to ‘LOW’.
5. For maximum heat turn control knob to ‘HIGH’.
6. To turn heater off, turn control knob to ‘OFF’.
7. Close the valve of the gas cylinder or the regulator after use.
OFF
LIGHT
LOW
HIGH
10
Always ensure the heater stands firmly; the glass tube may break if the heater was to fall
Never use the heater if the glass tube is damaged
LIGHTING INSTRUCTIONS
Check and ensure that an AA
battery is inside the ignition
chamber and has power. Ensure the
anode(+) faces outside.
1. Ensure that the control knob is OFF. Slowly open the gas
cylinder valve.
2. Press and turn the control knob to LIGHTposition, push the
igniter to generate spark while keeping control knob in pressed
position
3. Check for pilot flame through glass tube. If pilot does not light,
turn control knob to ‘OFF’ position wait two minutes
minimum and try again from the start. Some attempts may be
necessary.
4. If the pilot alight, keep control knob pressed for 15 seconds
then turn the control knob to ‘LOW’.
5. For maximum heat turn control knob to ‘HIGH’.
6. To turn heater off, turn control knob to ‘OFF’.
7. Close the valve of the gas cylinder or the regulator after use.
OFF
LIGHT
LOW
HIGH
LIGHTING INSTRUCTIONS
Check and ensure that an AA battery is inside the ignition chamber and
has power. Ensure the anode(+) faces outside.
1. Ensure that the control knob is OFF. Slowly open the gas cylinder valve.
2. Press and turn the control knob to LIGHT position, push the igniter to
generate spark while keeping control knob in pressed position.
3.
knob to ‘OFF’ position wait two minutes minimum and try again from
the start. Some attempts may be necessary.
4. If the pilot alight, keep control knob pressed for 15 seconds then turn
the control knob to ‘LOW’.
5. For maximum heat turn control knob to ‘HIGH’.
6. To turn heater off, turn control knob to ‘OFF’.
7. Close the valve of the gas cylinder or the regulator after use.
CLEANING AND MAINTENANCE:
● To ensure outstanding performance of your heater make sure to perform
the following maintenance activities on a regular basis:
● Keep exterior surfaces clean.
-
- While washing your unit, be sure to keep the area around the burner and pilot assembly dry
at all time. If the gas control is exposed to water in any way, do NOT use it. It must be replaced.
● Before use the unit should be inspected for spiders, spider webs or other insects.
●
Signs of possible blockage include:
-
- Heater does NOT reach the desired temperature.
- Heater glow is excessively uneven.
- Heater makes popping noises.
- Compressed air may help clear away smaller particles.
●
water if any carbon deposits develop. Always be careful when cleaning the glass tube.
STORAGE:
Between uses:
● Turn the control knob to “OFF” position.
● Turn LPG cylinder to “OFF” position.
● Store heater upright in an area sheltered away from weather conditions (such as rain, sleet, hail,
snow).
● If desired, cover heater to protect exterior surfaces and to help prevent dust and debris
collecting in air passages.
During periods of extended inactivity or when transporting:
● Turn the control knob to “OFF” position.
● Disconnect LPG Cylinder and move to a secure, well-ventilated location outdoors.
DO NOT store in a location that will exceed 50 degrees C.
● Store heater upright in an area sheltered away from weather conditions (such as rain, sleet, hail,
snow).
● If desired, cover heater to protect exterior surfaces and to help prevent dust and debris
collecting in air passages.
WARNING
FOR YOUR SAFETY:
● DO NOT touch or move heater for at least 45 minutes after use.
● Allow all burner elements to cool before touching.
NOTE
●In a salt-air environment (such as near an Ocean) corrosion occurs more quickly than normal.
● Frequently check for corroded areas and repair them promptly.
● Wait until heater is cool before covering.

10
TECHNICAL SPECIFICATIONS
GUARANTEE AND SERVICE
Your new product comes with a 12 month warranty. Defects affecting productCOMHARBOR LIMITED
be corrected by replacement or repair provided the product is used and maintainedfunctionality may
in accordance with the instructions. This does not apply to damage or wear sustained by improper
use of the accessories or the appliance. Your statutory rights are not affected. Documentation,
CUSTOMER SERVICES
If you wish to return your product for a full refund the item must be unused, in its original packaging
and returned in a sellable condition. Please contact our Customer Service team within 24 hours
who will be able to assist with your enquiry.
If they advise you to return the product to us please pack it carefully and include a note with your
name, address, daytime telephone number and details of the fault. If the product is still under
guarantee please include proof of purchase.
PROBLEM PROBABLE CAUSE SOLUTION
Pilot will not stay on Debris around pilot
Loose connections
Thermocouple bad
Gas leak in line
Lack of fuel pressure
Clean dirty area
Tighten connections
Replace thermocouple
Check connections
Pilot will not light Gas valve may be OFF
Tank fuel empty
Opening blocked
Air in supply system
Loose connections
Turn the gas valve ON
Clean or replace opening
Purge air from lines
Burner will not light Pressure is low
Opening blocked
Control not ON
Thermocouple bad
Pilot light assembly bent
Not in correct location
Remove and clean
Turn valve to ON
Replace thermocouple
Place pilot properly
Position properly and retry
13 kW
BE, CH, CY, CZ, ES,FR, GB, GR, IE, IT, LT, LU, LV, PT, SK, SI. 28-30/37mbar
30mbar
37mbar
AT, DE, CH, SK 50mbar
G30/G31 at
28-30mbar / 37mbar
G30 / G31 at
30mbar
G30 / G31 at
37mbar
G30 /G31 at
50mbar
1.45mm 1.40mm
□I3+(28-30/37) □I3B/P(30) □I3B/P(37) □I3B/P(50)
√
1.50mm1.50mm
Applicant : COMHARBOR LIMITED
Address : SWIFT 41 (UNIT D) SWIFT PARK, RUGBY, CV21 1DZ
PL
MODEL MX286961AAA
Nominal heat input: (Hs)
Appliance category:
Reference gas:
Normal gas pressure:
Injector size:
COUNTRY OF DESTINATION
I3+ for
I3B/P for
I3B/P for
I3B/P for
CY, CZ, DK, EE, FI, FR, HU, IT, LT, NL, NO, SE, SI, SK, RO, HR,
TR, BG, IS, LU, MT, MK, AL.
Pin 0359CO1324
0359 -21
Table of contents
Popular Patio Heater manuals by other brands

BlueRhino
BlueRhino Endless Summer 150000 Series Replacement manual

Mi-T-M
Mi-T-M MH-0042-PM11 Operator's manual

Fisher & Paykel
Fisher & Paykel DCS DRH-48N user guide

Dimplex
Dimplex BA 1200 Installation and operating manual

Outsunny
Outsunny 842-279V90 user manual

bauhaus
bauhaus ZHQ1288-RMHD-65 instruction manual

Lifestyle
Lifestyle CAPRI LFS841 instruction manual

Desa
Desa PG15EA Service manual

Wood Pellet Products
Wood Pellet Products WPPH001.3 owner's manual

Sealey
Sealey IFSH1809R instructions

Rinnai
Rinnai PATIOSSL Operating and installation instructions

Scheu Products Company
Scheu Products Company SPC-21-PHTTS owner's manual