Command access PD10-M-RIM User manual

PD10-M-RIM
Doc # 20200_B
1
INSTALLATION INSTRUCTIONS
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002
A.
PD10-M-RIM Includes
A. Head Cover pack
B. RIM Exit Device
C. Hinge Sle End Cap pack
D. Lock Sle End Cap pack
E. Rim Strike pack
F. MM4 - Installed in exit device
G. 6’ Power Lead
Tools Required
• Cordless Drill
• Needle nose Pliers
• Measuring Tape
• 1/2 Drill bit
The PD10-M-RIM is a storefront grade 1 exit device equipped with motor drive latch retracon.
Retrots Doromac 1790 & First Choice 3790.
B.
D. E. F.
C.
G.

2
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002
TECHNICAL INFORMATION
Specicaons
PTS Video
Click or Scan
• Input Voltage: 24VDC +/- 10%
• Average Latch Retracon Current: 1 Amp
• Average Holding Current: 125 mA
• Wire gauge: Minimum 18 gauge
Step 1-Press the device push pad to the desired seng. (this can be fully
depressed or less than fully depressed).
Step 2- While depressing the push pad, apply power. (i.e. presenng the
credenal to the reader).
Step 3- Connue to keep pad depressed, the device will beep 6 mes, roughly
5 seconds. Aer the beeps have stopped, release the pad and now the
adjustment is complete. If not to your liking repeat the three steps. That’s
all there is to it.
Setting PtS
2 Beeps
3 Beeps
5 Beeps
6 Beeps
7 Beeps
BeePS exPlanation Solution
Over Voltage
Under Voltage
Forced Release
Push pad is depressed. Device is
re-adjusng
Over-travel or mechanical
obstrucon
> 28V unit will shut down. Check voltage & adjust to 24 V.
< 22V unit will shut down. Check voltage & adjust to 24 V.
Device will automacally re-engage within 5 seconds.
Check to make sure the push pad is not stuck or catching on
anything.
trouBleShooting & DiagnoSticS
4 Beeps Failed Sensor Verify all 3 sensor wires are installed correctly. Replace sensor if
problem persists by contacng CAT tech support.
If mechanical obstrucon, remove & push pad down unl
beeping stops to reset. If no obstrucon, the pad may have
been pushed in too far during PTS calibraon. Recalibrate
with the pad slightly out. If problem persists, verify the
magnet is within 1/4” of the sensor at the end of travel.
**Important Info**
Make sure to set PTS before nishing installaon!
MM4 Label

3
Electried Exit Device
Installaon Example
RECOMMEND POWER SUPPLIES:
All Command Access exit devices & field installable kits have been thoroughly cycle tested with
Command Access power supplies at our factory.
• PS210
• PS220/220B
• PS440B
• PS480B
• PS1
• PS2/2B
• PS5-4
• PS5-6
For more informaon click here or go to our website
Module
Ceiling Tile
Legend
Optional Module
Placement
Standard Placement
Optional Placement
Module
GREEN
CHANNEL 1
LED
NORMALLY OPEN
DRY CONTACT FROM
ACCESS CONTROL
SYSTEM
NO VOLTAGE
LOCKING
HARDWARE
+
-
CAT

4
RIM Panic
Installaon Template
All prep is shown on interior side of the door,
except where noted.
Right hand door shown. (LHR)

5
Install the sle mounng bracket with 2 ea.
1/4-20 x 1/2 pan head screws. Leave space
to capture the base of the device. (See next
slide)
A.
STEP 1 - Mount Exit Device
Slide the end of baserail underneath the
mounng bracket.
B.
Oponal STEP - Installing Cylinder
A. Install trim cylinder tail piece so that it is
slightly below the face aer mounng.
Install key cylinder using mounng
screws supplied with cylinder. (Screws
may need to be shortened.)

6
Aach head of device to sle with 2 ea.
1/4-20 x 3/4 “ screws. Tighten screws on
the head and base of the device.
-For Night Latch, leave set screw in place.
-Hold Back funcon is desired, remove the set
screw to allow addional rotaon of cylinder
tailpiece.
STEP 1B - Connued
Remove lock sle end cap.
STEP 2 - Drill Wire Chase
A.
B.
A.

7
Slide push pad o of baserail.
Drill the hole for our 2 pin power lead in-
between the 2 mounng screws.
B.
C.
Feed the 2 pin power lead into the hole
and connect to our MM4 module. Also,
make sure to clean out any debris le.
D.
Debris
Note: Depending on where your power transfer is; next you would sh the other side of the power
lead we connected to the MM4 and hook up to your incoming power. If you have a portable tester
this would be a good me to test re the motor.

8
Replace push pad, making sure the acvang
brackets and pins slide through the 3rd channel.
E.
Reinstall the lock sle end cap.F.
STEP 3 - Install Head & End Cap
A. Install head cover with 2 ea. 10-32 x 3/8
screws.

9
Install the roller strike with 2ea. #10-32 x 1
“ screws so the roller is ush with the frame
stop. (Use strike shim for 5/16” stops.)
Install hinge sle push pad cover with 2
ea. 8-32 x 1 1/2” screws. Now you set you
latch retracon adjustment with our “PTS”
technology.
See page #2
B.
Using the roller strike as a template,
drill and tap rear mounng holes. Install
remaining 10-32 x 1” mounng screws and
ghten all screws.
STEP 4 - Install Door Frame Stop
A.
B.

10
Clean surface of the frame before
apply wear strip in indicated area.
Peel backer paper from wear strip.
Apply wear strip ush to front of frame jamb in indicated area.
Cut wear strip to desired length.
STEP 5 - Install Wear Strip
A.
B.
C.
D.

11
PD10 Parts Breakdown

12
Doc # 20200
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002