Command access VLP-M-KIT User manual

1
INSTALLATION INSTRUCTIONS
VLP-M-KIT
The Command Access VLP-M-KIT is a eld-installable motorized latch-pullback baserail kit for the Von
Duprin 33/35 & 98/99 series devices.
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002
Kit Includes
1 - VLP-M-KIT Baserail Kit
1 - 6’ Lead
1 - Dogging Hole Cap
B.
A.
C.
Tools Required
• Cordless Drill
• 5/16 Nut driver (recommended) or Flat head
screwdriver
• #2 Phillips head screwdriver
02/16 Doc # 20272_E
A.
B.
C.
Additional
Information

2
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002
Technical Information
Specications
PTS Video
Click or Scan
Step 1-Press the device push pad to the desired seng. (this can be fully
depressed or less than fully depressed).
Step 2- While depressing the push pad, apply power. (i.e. presenng the
credenal to the reader).
Step 3- Connue to keep pad depressed, the device will beep 6 mes. Aer the
beeps have stopped, release the pad and now the adjustment is complete.
If not to your liking repeat the three steps. That’s all there is to it.
Setting PtS
MM4 Switches
2 Beeps
3 Beeps
5 Beeps
6 Beeps
7 Beeps
BeePS exPlanation Solution
Over Voltage
Under Voltage
Forced Release
Push pad is depressed. Device is
re-adjusng
Over-travel or mechanical
obstrucon
> 28V unit will shut down. Check voltage & adjust to 24 V.
< 22V unit will shut down. Check voltage & adjust to 24 V.
Device will automacally re-engage within 5 seconds.
Check to make sure the push pad is not stuck or catching on
anything.
trouBleShooting & DiagnoSticS
4 Beeps Failed Sensor Verify all 3 sensor wires are installed correctly. Replace sensor if
problem persists by contacng CAT tech support.
• Input Voltage: 24VDC +/- 10%
• Average Latch Retracon Current: 1 Amp
• Average Holding Current: 170 mA
• Wire gauge: Minimum 20 gauge
If mechanical obstrucon, remove & push pad down unl
beeping stops to reset. If no obstrucon, the pad may have
been pushed in too far during PTS calibraon. Recalibrate
with the pad slightly out. If problem persists, verify the
magnet is within 1/4” of the sensor at the end of travel.
**Important Info**
Make sure to set PTS before nishing installaon!

3
Head cover
Bracket
Screws
Case
Push pad
• Remove head cover.
• Remove (2) screws attaching bracket
to baserail with 5/16 nut driver or
at head screw driver.
• Remove push pad by pulling pad
guides up then moving push pad
forward & then upward.
• Remove mounting bracket.
• Remove case for device.
1
4
2
3
• Detach the head assembly form the
base rail by removing both screws on
the backside of the baserail.
Screws

4
• Next plug in MM4 module to power &
test motor functions before nishing
reassembly.
• Remove the“C” clip and pin attaching
the latch to the baserail.
• Swap your mechanical baserail for the
electried baserail.
• Re-install the pin into the rst hole • Re-install “C” clip attaching the latch
to the new baserail.
• Re-install both screws attaching the
new baserail back to head assembly.
Screws

5
Push pad
Case
Bracket
Screws
Bracket
Head cover
1
4
2
3
• Replace bracket & attach (2) screws with 5/16
nut drive or at head screw driver.
• Replace push pad by placing over
activating arms & pushing down then
back towards end of device.
• Slide baseplate back into case being
careful of motor wires.
• Replace mounting bracket.
• Replace head cover & (4) head
cover screws if present.
• Depress push pad & set PTS adjustment.
Step 1-Press the device push pad to the desired seng. (this can be fully
depressed or less than fully depressed).
Step 2- While depressing the push pad, apply power. (i.e. presenng the
credenal to the reader).
Step 3- Connue to keep pad depressed, the device will beep 6 mes. Aer the
beeps have stopped, release the pad and now the adjustment is complete.
If not to your liking repeat the three steps. That’s all there is to it.
Setting PtS