Commax IDentry T20 Installation guide

Introduction
Cable-Connection
①
②
1. CN1) TCP/IP Connector
- Use TCP/IP to connect extension cable
2. CN501) Relay 1,2
- Connect with door lock, alarm device and etc.
3. CN503) Wiegand Input
-Connect with extension card reader
4. CN506) Wiegand Output
-Output to set-up card data
5. CN505) Sensor Input
- Connect to exit button or various sensors
(door contact, security sensor or etc.)
6. CN2) Power Input
- Supply 12V to desktop through power supply
7. CN3) RS485 / RS422(T20)
- Possible to use 485 or 422 communication
Component
Quantity
T20
1
Bracket
1
Cable
7
Screw
3
TCP/IP Extension Cable
1
For the full version of this manual, please visit COMMAX online
www.commax.com > Customer > Manual. Download full manuals for installation and user.
Access Control IDentry-T20 Total Manual
http://www.commax.co.kr/boardnew/lib/downfile.php?db=TB_ENGLISH_manual&fnum=112
Access Control IDentry-CAMS-S User Manual
http://www.commax.co.kr/boardnew/lib/downfile.php?db=TB_ENGLISH_manual&fnum=133
IDentry-T20
Quick Manual
1. Power: Connect DC12 Power supply to "CN2" Doesn’t matter the direction of the GND
and VCC.
2. TCP/IP: It can build access control system by LAN or WAN without limited distance if it
uses TCP/IP way. It can connect RJ45 of opposite after connecting CN1 using enclosed
extension cable.(See manual for IP settings)
July 2015 Ver. 1

3. WIEGAND OUT: It can only operate a card or fingerprint reader but not controller
if it connects with other main controller. At this time, it can use Wiegand out
socket(CN503) when information that has hands over to main controller.
4. RF card Reader: It can connect cable of card reader that is set CON4 if it connects
with RF card reader. Above picture shows connecting with T20-F(T20-C/T20-D).
5. Sensor: Above picture shows to control automatic sliding door and related
equipment. It is to connect cable from door contact, sensor, exit button and infrared
sensor like above picture.
6. Relay: T20 operates access control as a physical method that is installed various
sensors read various situations related with various equipment as above picture. It
operates equipment from various electric strikes to alarms connecting to CON4.
Cable-Connection
⑤
④
③
⑥
(ex:IDentry-T20-F)

Cautions
- Avoid direct sunlight or heat radiations.
- Do not use liquid solvent or wet cloth when cleaning. Use soft cloth.
-Do not put around strong magnetic things such as TV, monitor
and magnet.
- Call service centre if you have any problems.
- Be careful not to drip liquid such as water or beverage into the item.
- Do not renovate, repair or separate as you want randomly. A/S will not be
taken.
COMMAX Co.,Ltd. #531-11, Sangdaewon-dong, Jungwon-gu, Seongnam-city, Kyunggi-do, Korea
TEL [phone]~550 FAX [phone] Mail: [email protected]
1. Access to system menu.
2. Select "User" and press OK button.
3. Select "Delete" and press OK button.
4. Input password (USER ID) to delete and press OK button.
5. Select "Fingerprint" and/or "ID Card" to delete.
( If want to delete both fingerprint and card of the
relevant ID, select "Delete All")
6. Press OK button after selection.
7. Complete the delete.
8. Access to system menu.
9. Select "User" and press OK button.
10. Select "Set Temp IP" and press OK button.
11. Input Temp ID (Upto 8 digits ) and press OK button.
12. Input access admission times ( Min. 1, Max. 9) with this them ID
and Press OK button.
13. Setup Temp ID completed.
T20-F User-Registration
T20 series include two COMMAX cards in the product box specially for T20-C and T20-D
to use them as Register/Delete master card. Download Shortcut Tool software in order to
activate those two Register/Delete master cards. Then you may start using the two master
cards for registering or deleting cards. (Shortcut function can also be used for the other
way of managing registration)
Please access www.commax.com, download Shortcut software and read the full manual
for T20 online to start “activating master cards” process.
Card Registration
7. RS485 / RS422(T20): Connect 1 and 4 →RS485+. Connect 2 and 3 →RS485-.
It can be 422communication to connect 4 pins all.
Cable-Connection
Instruction of Fingerprint Type
1. Press fingerprint sensor for 3 seconds and access
to system menu
2. Move between menus using navigator button
⑦