Commax T65 User manual

Installation Manual
T65
www.commax.com
Thank you for purchasing COMMAX products.
Please carefully read this User’s Guide (in particular, precautions for safety) before using a product and
follow instructions to use a product exactly.
The company is not responsible for any safety accidents caused by abnormal operation of the product.

LAN
CN505 CN503 CN506
CN700 CN501
CN810
VR501 VR502
Back of T65

LAN
CN505 CN503 CN506
CN700 CN501
CN810
VR501 VR502
T65 CONNECTIONS
CN501) Relay 1, 2
- Connects with door lock and alarm devices
CN503) Card Reader
- Connects with external card reader
CN505) Sensor Input
- Connects with various sensors (door contact, alarm sensor etc)
and exit button
CN506) Wiegand output
- Outputs CARD data
(Used when it is integrated with other main controller)
CN700) Power Input / RS 485
- Supply 12V power to T-65 through power supply
- Communicate RS-485 with PC
CN810) TEL-LINE
- Connects with Extension Phone
LAN_RJ45) TCP/IP Connector
- Communicate TCP/IP with PC
VR501) Speaker Volume Switch
- Controls speaker volume
VR502) Mic Volume Switch
- Controls Mic volume

DIAGRAM (RS-485)
It is possible to connect numerous
T65 with computer.
Maximum number of connection with
one serial port is 16 T65.
Must give unique address to each
T65 (Refer to user manual for the setup)
If not, arouses communication collision and
cannot communicate.
RS-485
RS-485
RS-485
RS-485
RS-485
Converter
RS-232 #1
#2
#3
.
.
.
#16

NETWORK DIAGRAM (RS-485)
RS-485
RS-485
RS-485
RS-485
RS-485
Converter
RS-232
#33
#34
#35
.
.
.
#48
RS-485
RS-485
RS-485
RS-485
RS-485
Converter
#49
#50
#51
.
.
.
#64
RS-485
RS-485
RS-485
#17
#30
#31
.
.
.
#32
#1
#14
#15
.
.
.
RS-485
RS-485
RS-485
RS-232 RS-485
Converter
RS-485
Converter
RS-485
RS-485
RS-232
#16
Multi
Port
RS-232
Maximum number of connection
with one serial port is 16units.
If main computer controls above
6units of T65, needs to prepare
additional port. CAMS S supports
up to 4 RS-485 converters.
T65(Units)
16
32
48
64
1
2
3
4
Port (No)

DIAGRAM (LAN)
Shows LAN composition connecting numerous T65
Must give unique IP address to each T65 (Refer to user manual for the setup)
TCP/IP
HUB
.
.
.

DIAGRAM (WAN)
Shows the connection with
64units of T65.
(Needs 64 IP address)
TCP/IP HUB
.
.
.
TCP/IP
WAN
.
.
.
.
.
.
.
.
.

LAN CN505 CN503 CN506
CN700 CN501
CN810
VR501 VR502
DC 12V
GNC
VCC
Transformer
AC220V
60Hz
DC_IN
CN700
GND VCC
CN700(DC-In) connects with DC12V and GND.
Doesn’t matter the direction of the GND and VCC.
CABLE CONNECTION (POWER)
(Red) (Black)

LAN CN505 CN503 CN506
CN700 CN501
CN810
VR501 VR502
CABLE CONNECTION (EXTENSION PHONE)
CN810(TEL-LINE) connects with extension phone and doesn’t matter the direction.
To communicate with extension phone, press # button and extension phone number
Controls speaker volume using VR501 and Mic volume using VR502
CN810

Shows LAN composition connecting numerous T65
Must give unique IP address to each T65 (Refer to user manual for the setup)
LAN CN505 CN503 CN506
CN700 CN501
CN810
VR501 VR502
CABLE CONNECTION (RS-485)
Shows the connection CN700(DC-IN) and RS-232/485 Converter
CN700
DC_IN
from : PC
RS-232RS-485
MAX : 1200m (4000ft)
+12V
GND
RX-
RX+
TX=/A=
TX+/A+
ex) RS232-485 CONVERTER

LAN CN505 CN503 CN506
CN700 CN501
CN810
VR501 VR502
CABLE CONNECTION (TCP/IP)
HUB
TCP/IP
Shows TCP/IP connects with T65 using the HUB.
No distance limits using TCP/IP and configure access control system with LAN or WAN
(Refer to user manual or CAMS S software manual for the IP setup)

LAN CN505 CN503 CN506
CN700 CN501
CN810
VR501 VR502
CABLE CONNECTION (WIEGAND OUT)
If connected to other main controller, it works as a card reader or fingerprint reader only not controller.
CN506(Wiegand out) connects with card reader port of main controller and transmit the data via Wiegand
12V
GND
WIG 0 WIG 1
GND
CN506
LMP
RNT
DATA0 DATA1
PWR
RDE-A
U8
U1
RELAY1 RELAY2
ACU
(ex: PCSC IQ-Serise)

LAN CN505 CN503 CN506
CN700 CN501
CN810
VR501 VR502
CABLE CONNECTION (RF CARD READER)
CN503
Reader
(ex : KP-10)
Red:12V
Black : GND
Green : Date 0
White : Date 1
Blue : LED Control
Connects the cable of the RF card reader to CN503.
Connection would be variable for each reader. (Follow the manual of each RF card reader)

LAN CN505 CN503 CN506
CN700 CN501
CN810
VR501 VR502
CABLE CONNECTION (SENSOR)
Shows T65 connected with sliding door and relevant controls ; door contact, door sensor, exit button, infrared sensor.
CN505
Sliding Door
EXIT BUTTON
Invasion Sensor
(or Fire Alram)
Door Contact
Embedded
AutoDoor Sensor
Exit
GND
Door Contact
GND GND GND
Invasion(Fire)
Timed Input
+5V

LAN CN505 CN503 CN506
CN700 CN501
CN810
VR501 VR502
CABLE CONNECTION (RELAY)
Shows physical access controls of T65 by connecting many devices which detect certain situation through the sensors explained in the above.
Electric strike or alarm devices to be operated with T65 using the connection of CN501.
RELAY-1 RELAY-2
CN501
N.O. N.C.
COM COM
N.C.
N.O.
Alram
Alert
Device
GND
Transfomer
Electric Magnetic
Lock
DC12V