Commell LP-170 User manual

LP-170
Pico-ITX
User’s Manual
Edition 1.1
2010/05/13

LE-375 User’s Manual
-1-
Copyright
Copyright 2009. All rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice to
make improvements to the products.
This document contains proprietary information and protected by copyright. No part of
this document may be reproduced, copied, or translated in any form or any means
without prior written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are property of
their respective owners. Disclaimer
The company shall not be liable for any incidental or consequential damages resulting
from the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including
without limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications
of the product described within it at any time without notice and without obligation to
notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT

LP-170 User’s Manual
-2-
Serial ATA Ribbon
Cable x 1
(OALSATA-L)
Dual COM PORT cable x 1
(OALES-BKU2NB)
Packing List:
Please check the package content before you starting using the board.
Hardware:
LE-375 PICO-ITX“ Miniboard x 1
Cable Kit:
Audio Cable x 1
(OALPJ-HDUNB)
PS/2 keyboard & mouse cable x 1
(OALPS2/MK)
USB Cable x 1
OALUSBA-3
DC_IN Power Cable x 1
(OALDC-3)
DC_OUT Power Cable x 1
(OALS1P1-6P-L20)

LP-170 User’s Manual
-3-
Option:
Pennal Inverter Cable x 1
Printed Matters:
Driver CD x 1 (Including User’s Manual)
(OALINV-5P-L15)

LP-170 User’s Manual
-4-
Index
Chapter 1 <Introduction>.................................................................................7
1.1 <Product Overview> .............................................................................................7
1.2 <Product Specification>........................................................................................8
1.3 <Mechanical Drawing>.......................................................................................10
1.4 <Block Diagram>................................................................................................ 11
Chapter 2 <Hardware Setup>.........................................................................12
2.1 <Connector Location>.........................................................................................12
2.2 <Jumper Reference>............................................................................................14
2.3 <Connector Reference>.......................................................................................15
2.3.1 <Internal Connector>........................................................................15
2.3.2 <External Connector>.......................................................................15
2.4 <CPU and Memory Setup>.................................................................................16
2.5 <CMOS & ATX Setup>......................................................................................17
2.6 <CF Interface> ....................................................................................................18
2.7 <Serial ATA Interface>.......................................................................................19
2.8 <LAN Interface>.................................................................................................19
2.9 <Onboard Display Interface>..............................................................................20
2.9.1 <Analog VGA Interface> .................................................................20
2.9.2 <Digital Display> .............................................................................21
2.10 <Onboard Audio Interface> ..............................................................................25
2.11 <USB2.0 Interface> ..........................................................................................26
2.12 <Serial Port Jumper Setting >............................................................................27
2.13 <Power & FAN Connector >.............................................................................28
2.13.1 <Power Input> ................................................................................28
2.13.2 <Power Output>..............................................................................29
2.13.3 <Fan Connector> ............................................................................30
2.14 <Indicator and Switch> .....................................................................................31
Chapter 3 <BIOS Setup> ................................................................................33
Appendix A <I/O Port Pin Assignment> .......................................................35

LP-170 User’s Manual
-5-
A.1 <LPC Port>.........................................................................................................35
A.2 < CRT Port >.......................................................................................................35
A.3 <LAN Port>........................................................................................................35
Appendix B <Flash BIOS> .............................................................................36
B.1 BIOS Auto Flash Tool.........................................................................................36
B.2 Flash Method.......................................................................................................36
Appendix C <System Resources> ................................................................37
C.1 .a<I/O Port Address Map>(LP-170G).................................................................37
C.2.a<Memory Address Map >(LP-170G)................................................................39
C.3 .c< System IRQ Resources >(LP-170G).............................................................40
Appendix E <Watch Dog timer Setting >......................................................41
Contact Information........................................................................................43

LP-170 User’s Manual
-6-
(This page is left for blank)

LP-170 User’s Manual
-7-
Chapter 1 <Introduction>
1.1 <Product Overview>
LP-170G/H/A is the PICI-ITX miniboard, with Intel® Atom N450/D410/D510 processor,
integrated GMA3150 graphics, Intel® ICH8-M, DDR2 SO-DIMM memory, Realtek HD
Audio, CF, SATAII and Intel® 82583V Gigabit LAN.
Intel® Atom Processor
The Intel® Atom N450(D410/D510) processor supports one channel of
667(667/800)MHz DDR2 SDRAM. The chipset features power-efficient graphics with an
integrated 18-bit 3D graphics engine based on Intel® Graphics Media Accelerator 3150
architecture with LVDS, CRT display ports. The DMI is designed into the Pineview-M(D)
processor to provide an efficient high-bandwidth communication channel between the
processor and the ICH8M.
Embedded Intel® ICH8-M
The board integrates Intel® ICH8M. It provides I/O capabilities and flexibility via
high-bandwidth interfaces such as PCIE and Hi-Speed USB 2.0 connectivity. Serial
ATA. HD Audio.
Flexible Extension Interface
The board also provides Compact Flash Type II socket and one PCIE mini card socket.

LP-170 User’s Manual
-8-
1.2 <Product Specification>
General Specification
Form Factor PICO-ITX miniboard
CPU Intel® Atom N450 processor 1.66GHz (LP-170G)
Intel® Atom D410 processor 1.66GHz (LP-170H)
Intel® Atom D510 processor 1.66GHz (LP-170A)
Package type: FCBGA8
Memory 1 x 200-pin DDR2 SO-DIMM 667MHz SDRAM up to 2GB
(LP-170G Only)
1 x 200-pin DDR2 SO-DIMM 667/800MHz SDRAM up to 2GB
(LP-170H/A Only)
Unbufferred, none-ECC memory supported only
Chipset Intel® ICH8M
BIOS Phoenix-Award v6.00PG 8Mb SPI flash BIOS
Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant
Watchdog Timer System reset programmable watchdog timer with 1 ~ 255
sec./min. of timeout value
Real Time Clock Intel® ICH8-M built-in RTC with lithium battery
Enhanced IDE One CompactFlash Type II socket on solder side
Serial ATA Intel® ICH8M integrates 1 Serial ATAII interfaces
(No RAID Function)
Up to 300MB/s of transfer rate
Multi-I/O Port
Chipset Intel® SCH with Winbond® W83627DHG controller
Serial Port Two RS-232 serial port
USB Port Four internal Hi-Speed USB 2.0 ports with 480Mbps of transfer
rate
K/B & Mouse PS/2 keyboard and mouse port
VGA Display Interface
Chipset Intel® Atom N450 processor (System Controller Hub) (LP-170G)
Intel® Atom D410 processor (System Controller Hub) (LP-170H)
Intel® Atom D510 processor (System Controller Hub) (LP-170A)
Frame Buffer Up to 384MB shared with system memory
Display Type CRT, LCD monitor with analog display, LVDS
Connector External DB15 female connector
Onboard 20-Pin LVDS and 5-Pin inverter connector
Ethernet Interface

LP-170 User’s Manual
-9-
Controller 1 x Intel® 82583V Gigabit Ethernet controller
Type Triple speed 10/100/1000Base-T
auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Connector 1 X External RJ45 connector with LED
Audio Interface
Chipset REALTEK ALC888
Interface Stereo audio Line-out and MIC-in
Connector Onboard audio connector with pin header
Expansive Interface
PCIE mini card 1 x PCIE mini card socket
Power and Environment
Power
Requirement DC 12V input with onboard 2-pin connector
Dimension 100 (L) x 72(H) mm
Temperature Operating within 0 ~ 60℃
Storage within -20 ~ 85℃
Ordering Code
LP-170G Support Intel® Atom N450 processor with onboard VGA,
LVDS for 18bit, Audio, Giga LAN, USB2.0, CF, PCIE mini card
LP-170H Support Intel® Atom D410 processor with onboard VGA,
LVDS for 18bit, Audio, Giga LAN, USB2.0, CF, PCIE mini card
LP-170A Support Intel® Atom D510 processor with onboard VGA,
LVDS for 18bit, Audio, Giga LAN, USB2.0, CF, PCIE mini card
The specifications may be different as the actual production.
For further product information please visit the website at TUhttp://www.commell.com.twUT

LP-170 User’s Manual
-10-
1.3 <Mechanical Drawing>
Unit: inch

LP-170 User’s Manual
-11-
W83627DHG
CRT
DDR2 SODIMM 2GB max.
PS2 KB/MS
RS232
LPC
PCIE mini card socket
PCIE Giga LAN
Compact Flash
USB port
ALC888 HD Audio
1.4 <Block Diagram>
18bit Single Channel LVDS
Serial ATA II
BIOS ICH8M
Intel® Atom
N450

LP-170 User’s Manual
-12-
CN_LPC
CN_AUDIO
CN_USB2
CN_USB1
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
CN_COM1/2
FAN
SATA
CN_LVDS
JFRNT
DC_IN
MINI_CARD

LP-170 User’s Manual
-13-
RJ45 PS2 CRT
CN_INV
DC_OUT
DDRII
CF
LP-170G/H/A

LP-170 User’s Manual
-14-
JAT
2.2 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting
JVLCD LCD Panel Voltage Setting
JAT AT/ATX Mode Setting
JRTC
JVLCD

LP-170 User’s Manual
-15-
2.3 <Connector Reference>
2.3.1 <Internal Connector>
Connector Function Remark
DDRII 200 -pin DDR2 SO-DIMM SDRAM slot Standard
SATA1 7-pin Serial ATA connector Standard
CF Compact Flash Type II socket Standard
MINI_CARD PCIE mini card socket Standard
CN_LVDS 10 x 2-pin LVDS connector Standard
CN_INV 5-pin LCD inverter connector Standard
CN_USB1/2 5 x 2-pin USB connector Standard
CN_AUDIO 5 x 2-pin audio connector Slim
CN_COM1/2 10 x 2-pin com connector Slim
JFRNT 10-pin switch/indicator connector Standard
FAN 3-pin system cooler fan connector Standard
DC_OUT 4-pin power output connector Standard
DC_IN DC input connector Standard
2.3.2 <External Connector>
Connector Function Remark
CRT DB15 VGA connector Standard
PS2 PS/2 keyboard and mouse connector Standard
RJ45 RJ45 LAN connector Standard

LP-170 User’s Manual
-16-
2.4 <CPU and Memory Setup>
Non-ECC, unbuffered memory is supported only.
LP-170G provides one 200-pin DDR2 SO-DIMM to support DDR2 667 memory
modules support up to 2GB of capacity.
Suggest:
DDR2 SO-DIMM Modules:
–Raw Card A = 2 Ranks of x16 SDRAMs (Double-sided)
–Raw Card C = 1 Rank of x16 SDRAMs (Single-sided)
LP-170H/A provides one 200-pin DDR2 SO-DIMM to support DDR2 667/800 memory
modules support up to 4GB of capacity.
Suggest:
DDR2 SO-DIMM Modules:
–Raw Card C = 1 Rank of x16 SDRAMs (Single -sided)
–Raw Card D = 1 Rank of x8 SDRAMs (Single-sided)
–Raw Card E = 2 Rank of x8 SDRAMs (Double -sided)
DDRII

LP-170 User’s Manual
-17-
2.5 <CMOS & ATX Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.
Jumper: JRTC
Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS
2-3 Normal Operation
Default setting
Jumper: JAT
Type: onboard 3-pin jumper
JAT Mode
1-2 AT Mode
2-3 ATX Mode
Default setting
JAT
JRTC
1 3
1
3

LP-170 User’s Manual
-18-
2.6 <CF Interface>
The board has one Compact Flash Type II socket on the solder side.
CF