Comnet CWFE2SCM2 User manual

QUICK START GUIDE
CWFE2SC(M,S)2
Commercial Grade 10/100 Mbps Ethernet
2 Port Electrical-to-Optical Media Converter
The ComNet ValueLine CWFE2SC(M,S)2 Ethernet 2-port media converters are designed
to transmit and receive a single channel of 10/100 Mbps data over multimode or single
mode optical fiber. The electrical interface will Auto-Negotiate to a 10 Mbps, or 100 Mbps
Ethernet rate without any adjustments. The optical interface operates at a 100 Mbps
Ethernet rate. These media converters are commercial grade for light industrial use.
Rev. 11.17.17
This guide serves the following
ComNet Model Numbers:
CWFE2SCM2
CWFE2SCS2

QSG_CWFE2SC(M,S)2 Rev. 11.17.17 PAGE 2
QUICK START GUIDE CWFE2SC(M,S)2
TECH SUPPORT: 1.888.678.9427
Front Panel
The Front Panel of the ComNet CWFE2SC(M)(S)2 consists of one RJ45 Port (Auto MDI/MDIX),
6 LED Indicators (UTP 100, LK/ACT, FDX/COL, Fiber LK/ACT, FDX/COL and PWR) and one fiber
100Base-FX Port.
Fast Fiber Converter Module - SC Model
LED Indicators
There are 6 diagnostic LEDs located on the Front panel of the media converter. They provide real-
time information of system and optional status. The indicator includes Power, UTP 100, LK/ACT,
FDX/COL, Fiber LK/ACT, FDX/COL. The following table provides description of the LED status and
their meanings.
LED Color Status Description
PWR Green On Power On
100 Green On 100 Mbps UTP Speed
Off 10 Mbps UTP Speed
LK/ACT (UTP) Green On The unit is linking with its link partner.
Green Blinking The unit is transmitting or receiving packets from UTP devices.
Off No device attached
LK/ACT (Fiber) Green On The unit is linking with its link partner.
Green Blinking The unit is transmitting or receiving packets from FX devices.
Off No device attached
FDX/COL (UTP) Orange On The UTP port is operating in full-duplex mode.
Orange Blinking Collision of packets is occurring in the port.
Off Half-duplex mode or no device attached.
FDX/COL (Fiber) Orange On The fiber port is operating in full-duplex mode.
Orange Blinking Collision of packets is occurring in the port.
Off Half-duplex mode or no device attached.

QSG_CWFE2SC(M,S)2 Rev. 11.17.17 PAGE 3
QUICK START GUIDE CWFE2SC(M,S)2
TECH SUPPORT: 1.888.678.9427
DIP-switch
The DIP-switch is used to configure operation mode for LLF (Link Lost Forwarding) and operation
mode for UTP/Fiber port. The default value of DIP switch is OFF.
SW No Status Description
1ON UTP 100 Mbps Full Duplex Mode
OFF UTP Auto-Negotiate
2ON Fiber in Half Duplex
OFF Fiber in Full Duplex
3ON LLF Enable
OFF LLF Disable
4ON Pure Converter mode
OFF Switch Converter mode
Rear Panel
The rear panel contains a power socket, which accepts 5-12 VDC @ 2.7 W.
Connect the included Power Supply to the rear panel DC IN jack.
Plug the AC input of the Power Supply to a commercial power source.
DC IN
Fast Fiber Converter Module - Rear Panel
Connections
CAT5e CAT5e
2 Multimode
or Single Mode
Optical Fibers
Ethernet
Device
CWFE2SC CWFE2SC
Ethernet
Device
POWER
SUPPLY
POWER
SUPPLY

© 2017 Communications Networks Corporation. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks, LLC.
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | [e-mail]
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: [phone] | F: [phone] | [e-mail]
MECHANICAL INSTALLATION INSTRUCTIONS
Full Documentation
This Quick Start Guide is only partial installation information, intended for users who need only
the default settings for this product model. To change settings or for more detailed explanation
of features and settings, please consult the full Installation Manual, provided on disk with the
product or available at www.comnet.net.
ComNet Customer Service
Customer Care is ComNet Technology’s global service center, where our professional staff is
ready to answer your questions at any time.
Email ComNet Global Service Center: [e-mail]