Comnet FVT10D2I1C4E User manual

INS_FVT/FVR20D2I1C4E_REV- 06/22/12 PAGE 1
INSTALLATION AND OPERATION MANUAL
FVT/FVR10D2I1C4E
10-BIT DIGITALLY ENCODED VIDEO
+ 2 BI-DIRECTIONAL DATA + AIPHONE™INTERCOM
+ 4 CONTACT CLOSURE
+ 100MB ETHERNET
+ REDUNDANT POINT-TO-POINT DUAL SFP OPTICAL PORTS
The FVT/FVR10D2I1C4E series utilize 10-bit digital video encoding and decoding
for high-quality video transmission that meets the requirements of EIA RS-250C
for short-haul video transmission. These environmentally hardened units provide
transmission of one video channel and two bi-directional data channels. They also
provide transmission of one Aiphone™intercom channel and four contact closure
channels with tamper supervision in addition to one 10/100Mb Ethernet channel.
The ComNet™FVT/FVR10D2I1C4E has dual optical (SFP) ports to provide a redundant
point-to-point fail safe topology in the event of loss of one fiber or one optical module.
Operational status can be monitored by using the web management interface
through the addition of the ComNet network managed chassis and network
management interface module.
Bi-color (red/green) LED indicators are provided for confirming operating status in
addition to alarm contacts for fault monitoring. See Figure 15 on Page 9 for LED
explanations.
Packaged in the exclusive ComNet ComFit housing, these units may be either wall
or rack-mounted (using ComNet C2 network-managed rack), or may be DIN-rail
mounted by the addition of ComNet model DINBKT1 adaptor plate. See Figure A on
Page 10 for mounting instructions.

INS_FVT/FVR20D2I1C4E_REV- 06/22/12 PAGE 2
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVT/FVR20D2I1C4E
10/100
ETHERNET
10/100
ETHERNET
FIGURE 2 – FVT10D2I1C4E TRANSMITTER
FIGURE 1 – FVT/FVR10D2I1C4E TRANSMITTER AND RECEIVER
Optical fiber determined by Selection of Small Form-factor Pluggable (SFP) modules*.
FIGURE 3 – FVR10D2I1C4E RECEIVER
REAR PANEL REAR PANELFRONT PANEL FRONT PANEL
(–) BLACK
(+) BLACK W/ WHITE STRIPE
Power Supply:
Dual 8-24VDC @ 4W
Rack Mount: C2 Network-Managed
NOTE: Remove PWR1 Electrical
Connector for Rack Mount Units
(–) BLACK
(+) BLACK W/ WHITE STRIPE
* One SFP required for point-to-point operation. Two SFPs required for redundant operation.
Consult factory for compatible SFP Modules.

INS_FVT/FVR20D2I1C4E_REV- 06/22/12 PAGE 3
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVT/FVR20D2I1C4E
FIGURE 4 – RJ45 BREAK-OUT – FVT10D2I1C4E TRANSMITTER
4 pc. Factory Supplied
PIN # Wire Color TX Connections
1 Blue IN 1+
2 Orange IN 1–
3 Black IN 2+
4 Red IN 3+
5 Green IN 3 –
6 Yellow IN 2–
7 Brown IN 4+
8 White IN 4–
PIN # Wire Color Aiphone Connections
1 Blue LE-D ‘-’ TERMINAL
2 Orange LE-D ‘1’ TERMINAL
3 Black LE-D ‘E’ TERMINAL
4 Red RELAY OUTPUT COM
5 Green RELAY OUTPUT N.C.
6 Yellow RELAY OUTPUT N.O.
7 Brown GND
8 White GND
PIN # Wire Color Data Connections
1 Blue DATA OUT –
2 Orange DATA OUT +
3 Black DATA IN +
4 Red RELAY OUT
5 Green RELAY OUT
6 Yellow DATA IN –
7 Brown GND
8 White +5V (BIAS)
VIEW INSIDE RJ-45 PORT
RJ-45 PORTS
Located on Rear Panel
RJ-45 BREAK-OUT KIT
Screw Number Corresponds to RJ-45 Port Pin Number
CADD
C (CONTACT PORT)
A (AIPHONE™ PORT)
D (DATA PORTS)

INS_FVT/FVR20D2I1C4E_REV- 06/22/12 PAGE 4
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVT/FVR20D2I1C4E
FIGURE 5 – RJ45 BREAK-OUT – FVR10D2I1C4E RECEIVER
4 pc. Factory Supplied
PIN # Wire Color RX Connections
1 Blue OUT1 +
2 Orange OUT1 –
3 Black OUT2 +
4 Red OUT3 +
5 Green OUT3 –
6 Yellow OUT2 –
7 Brown OUT4 +
8 White OUT4 –
PIN # Wire Color Aiphone Connections
1 Blue LEF ‘E’ TERMINAL
2 Orange LEF ‘1’ TERMINAL
3 Black LEF ‘–’ TERMINAL
4 Red NC
5 Green CONTACT INPUT +
6 Yellow NC
7 Brown GND
8 White GND
PIN # Wire Color Data Connections
1 Blue DATA OUT –
2 Orange DATA OUT +
3 Black DATA IN +
4 Red RELAY OUT
5 Green RELAY OUT
6 Yellow DATA IN –
7 Brown GND
8 White +5V (BIAS)
VIEW INSIDE RJ-45 PORT
RJ-45 PORTS
Located on Rear Panel
RJ-45 BREAK-OUT KIT
Screw Number Corresponds to RJ-45 Port Pin Number
CADD
C (CONTACT PORT)
A (AIPHONE™ PORT)
D (DATA PORTS)
NC = No Connection

INS_FVT/FVR20D2I1C4E_REV- 06/22/12 PAGE 5
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVT/FVR20D2I1C4E
PIN # Wire Color Data Connections
1 Blue DATA OUT –
2 Orange DATA OUT +
3 Black DATA IN +
4 Red RELAY OUT
5 Green RELAY OUT
6 Yellow DATA IN –
7 Brown GND
8 White +5V (BIAS)
PIN # RS232 RS422 RS485 2-Wire RS485 4-Wire
1 NC RS422 OUTPUT – NC RS485 OUTPUT –
2RS232 – OUTPUT RS422 OUTPUT + NC RS485 OUTPUT +
3 NC RS422 INPUT + RS485 INPUT + RS485 INPUT +
4RELAY OUT RELAY OUT RELAY OUT RELAY OUT
5RELAY OUT RELAY OUT RELAY OUT RELAY OUT
6RS232 – INPUT RS422 INPUT – RS485 INPUT – RS485 INPUT –
7 GND GND GND GND
8+5V (BIAS) +5V (BIAS) +5V (BIAS) +5V (BIAS)
FIGURE 6 – DATA SWITCH POSITIONS
The mode for each data channel is configured using a set of two switches labeled DATA1 (S3) and DATA2 (S4), located on the front panel of the unit.
FIGURE 7 – RJ-45 PIN OUT
DATA1 (S3) DATA2 (S4)
Resulting Mode1212
ON ON ON ON RS232
ON OFF ON OFF RS422, Bi-Phase or Manchester
OFF ON OFF ON RS485 2-Wire, Sensornet
OFF OFF OFF OFF RS485 4-Wire
NC = No Connection

INS_FVT/FVR20D2I1C4E_REV- 06/22/12 PAGE 6
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVT/FVR20D2I1C4E
FIGURE 8 – DATA CONNECTIONS
See Page 5 for Switch Settings
RS232
Customer
Equipment FVT10D2I1C4E
Customer
Equipment
FVR10D2I1C4E
RS422
Bi-phase or
Manchester
DOUT(+)
DOUT(-)
DIN(+)
DIN(-)
Data In (+)
Data In (-)
Data Out (+)
Data Out (-)
2-Wire
RS485,
Sensornet
DIN(+)
DIN(-)
DIN(+)
DIN(-)
Data (A)
Data (B)
Data (A)
Data (B)
Data Transmit
Data Receive
Signal Ground
DIN(-)
DOUT(+)
GND
DOUT(+)
DIN(-)
GND
Data Receive
Data Transmit
Signal Ground
4-Wire
RS485
DIN(+)
DIN(-)
DOUT(+)
DOUT(-)
DOUT(+)
DOUT(-)
DIN(+)
DIN(-)
Data Out (A)
Data Out (B)
Data In (A)
Data In (B)
Data In (A)
Data In (B)
Data Out (A)
Data Out (B)
DIN(+)
DIN(-)
DOUT(+)
DOUT(-)
DOUT(+)
DOUT(-)
DIN(+)
DIN(-)
Data Out (+)
Data Out (-)
Data In (+)
Data In (-)
Data In (+)
Data In (-)
Data Out (+)
Data Out (-)
FIGURE 9 – POSSIBLE ETHERNET CONFIGURATION
Ethernet IEEE 802.3
Network Element
Ethernet IEEE 802.3
Network Element
FVT10D2I1C4E FVR10D2I1C4E
CAT5e/6 with
RJ45 Connections
CAT5e/6 with
RJ45 Connections
Optical Fiber
SC or LC
Connectors
SINGLE FIBER
SFP MODULE
Ethernet IEEE 802.3 Network Element determined by user.

INS_FVT/FVR20D2I1C4E_REV- 06/22/12 PAGE 7
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVT/FVR20D2I1C4E
FVT10D2I1C4E
FVT10D2I1C4E
Form ‘C’ Relay
Output
LE-D FVR10D2I1C4E
Door/Barrier
Contact Input
LEF
FVR10D2I1C4E
10/100
ETHERNET
FIGURE 10 – SFP CONNECTIONS
Number of fibers and type of fiber connectors will be determined by selected SFP modules and if point-to-point or redundant modes are required.
FIGURE 11 – AIPHONE™INTERCOM CONNECTIONS
The units are designed to operate with the Aiphone™LE-D and LEF intercom system.
PIN # Wire Color Aiphone Connections
1 Blue LEF ‘E’ TERMINAL
2 Orange LEF ‘1’ TERMINAL
3 Black LEF ‘–’ TERMINAL
4 Red NC
5 Green CONTACT INPUT +
6 Yellow NC
7 Brown GND
8 White GND
PIN # Wire Color Aiphone Connections
1 Blue LE-D ‘-’ TERMINAL
2 Orange LE-D ‘1’ TERMINAL
3 Black LE-D ‘E’ TERMINAL
4 Red RELAY OUTPUT COM
5 Green RELAY OUTPUT N.C.
6 Yellow RELAY OUTPUT N.O.
7 Brown GND
8 White GND
3 –3E
2 121
1 E
5 54 76
1–

INS_FVT/FVR20D2I1C4E_REV- 06/22/12 PAGE 8
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVT/FVR20D2I1C4E
FIGURE 12 – CONTACT SWITCH POSITIONS
The mode for contact closure operation is configured using a set of two switches labeled CONTACT (S1) located on the front panel of the unit. There are four
supervised contacts in the forward (video) direction.
FIGURE 13 – CONTACT CLOSURE SUPERVISED INPUT CIRCUIT
NOTE: These switch settings refer to the trans-
mitter (FVT10D2I1C4E). On the receiver
(FVR10D2I1C4E), S1 SWITCH 1 inverts the
contact outputs. S1 SWITCH 2 is not used.
CONTACT (S1)
Resulting Mode1 2
ON ON Full Supervision – When a 1K resistor is connected in series with
the contact closure input, and a 1K resistor is connected in parallel
across the contact closure input. Both open circuits and short
circuits can be detected as well as normal opens and closes.
ON OFF Series Supervision – When a 1K resister is connected in series with
the contact closure input. In this mode, shorts across the contact
inputs can be detected but open circuits cannot be detected.
OFF ON Parallel Supervision – When a 1K resistor is connected in parallel
across the contact closure input. In this mode, open circuits can be
detected but short circuits cannot be detected.
OFF OFF No Supervision – The contacts will behave as normal contacts with
no Supervision.
INTERNAL
1K
1K
5V
1K Series*
1K
Parallel*
* Optional external resistors
(provided) are required for
supervision. Place close to
the switch for optimal results.

INS_FVT/FVR20D2I1C4E_REV- 06/22/12 PAGE 9
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVT/FVR20D2I1C4E
FIGURE 15 – LED INDICATORS
FIGURE 14 – ALARM SWITCH POSITIONS
The mode for alarm operation is configured using a set of two switches labeled ALARM (S2) located on the front panel of the unit. There are two alarm out-
puts on each unit. One on each RJ45 data connector. See Figures 4 & 5 on Pages 3 & 4.
NOTE: The ALARM will also open when Fiber Link
on either SFP port is lost or if Power is lost
on either unit.
GREEN Solid: Link (no activity)
Blinking: Activity
Off: No link
YELLOW Solid: Highest data rate (100Mbs)
ALARM (S2)
Resulting Mode1 2
ON ON Alarm 1 – SFP 1 Failure
Alarm 2 – SFP 2 Failure
ON OFF Alarm 1 – SFP 1 or SFP 2 Failure
Alarm 2 – Video Loss
OFF ON Alarm 1 – SFP 1 Failure or Video Loss
Alarm 2 – SFP 2 Failure or Video Loss
OFF OFF Alarm 1 – SFP 1 or SFP 2 Failure or Video Loss
Alarm 2 – SFP 1 or SFP 2 Failure or Video Loss
OFF RED GREEN FLASHING
SFP SFP not installed No optical link Link is good and is in use Link is good but is not in
use
VIDEO – No video signal An active video
signal is present –
10/100 LINK – No Ethernet signal Ethernet signal linked –
CONTACT (C) One or more contacts are
open Fiber link failed All four contacts are closed –
CONTACT (S) –Supervised contact alarm
or fiber link failed
No supervised contacts in
alarm state –
LE-D – Quiet / No Audio Audio Present Call button active
LE-F – Quiet / No Audio Audio Present –
DATA IN Tri-state Low state High state Data activity
DATA OUT Tri-state Low state High state Data activity
POWER Unit powered down – Unit powered up –

INS_FVT/FVR20D2I1C4E_REV- 06/22/12 PAGE 10
© 2013 Communications Networks Corporation. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks, LLC.
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | [e-mail]
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: [phone] | F: [phone] | [e-mail]
INSTALLATION CONSIDERATIONS
This fiber-optic link is supplied as a Standalone/Rack module. Units
should be installed in dry locations protected from extremes of
temperature and humidity.
C2 NETWORK MANAGED RACKS
CAUTION: Although the units are hot-swappable and may be installed
without turning power off to the rack, ComNet recommends that the
power supply be turned off and that the rack power supply is disconnected
from any power source. Note: Remove electrical connector before
installing in card cage rack.
1. Make sure that the card is oriented right side up, and slide it into the
card guides in the rack until the edge connector at the back of the card
seats in the corresponding slot in the rack’s connector panel. Seating
may require thumb pressure on the top and bottom of the card’s front
panel.
CAUTION: Take care not to press on any of the LEDs.
2. Tighten the two thumb screws on the card until the front panel of the
card is seated against the front of the rack.
WARNING: Unit is to be used with a Listed Class 2 power supply.
IMPORTANT SAFEGUARDS:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may
be greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is not
compromised.
MECHANICAL INSTALLATION INSTRUCTIONS
.313 [7.95 mm]
.156 [3.96 mm]
FIGURE A
Dimensions are for a standard ComNet™two slot module