Compaq P1100 User manual

Compaq P1100 Color Monitor
User’s Guide
Compaq P1100 Color Monitor
325603-001

Part Number: 144437-001 - Writer: Marianne Silvetti - Saved by: MSilvetti
Saved date: 09/16/99 12:09 PM
File Path: P:\Docs\Monitors\Mayflower
Notice
The information in this guide is subject to change without notice.
COMPAQ COMPUTER CORPORATION SHALL NOT BE
LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR
OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES RESULTING FROM THE
FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.
This guide contains information protected by copyright. No part of
this guide may be photocopied or reproduced in any form without
prior written consent from Compaq Computer Corporation.
1999 Compaq Computer Corporation.
All rights reserved. Printed in Singapore.
Compaq and Deskpro are registered in the U. S. Patent and
Trademark Office.
Microsoft, MS-DOS, Windows, Windows NT, and other names of
Microsoft products referenced herein are trademarks or registered
trademarks of Microsoft Corporation.
ENERGY STAR is a U.S. registered mark.
Product names mentioned herein may be trademarks and/or
registered trademarks of their respective companies.
The software described in this guide is furnished under a license
agreement or nondisclosure agreement. The software may be used
or copied only in accordance with the terms of the agreement.
First Edition (July 1999)
Part Number 325603-291
CD-ROM Part Number 153303-001
Compaq Computer Corporation
User’s Guide
Compaq P1100 Color Monitor

English 1-1
ttttt
Part Number: 325603-001- Writer:Carol Benjamin Name - Saved by:
Pages: 16 Words: 2796 Saved date: 10/27/99 5:20 PM File Name: P1100
English
Product Features
The Compaq P1100 Color Monitor is a microprocessor-based, high-
resolution monitor with auto-scanning. The monitor features include the
following:
?# 21-inch (19.8-in/50.3 cm viewable) FD Trinitron®CRT
?# 1920 × 1440 resolution, plus full-screen support for lower
resolutions
?# On-Screen Display (OSD) adjustments in nine different languages:
English, Dutch, French, German, Italian, Spanish, Russian,
Swedish, and Japanese for ease of set-up and screen optimization
?# Plug and Play capability if supported by your system
?# Tilt and swivel functionality
?# Kodak Color Profile (included on CD-ROM)
?# CD-ROM includes an information file (INF), Image Color
Matching file (ICM), and product documentation
?# Automatic scanning of all horizontal frequencies between 30 and
121 kHz, and vertical frequencies between 50 and 160 Hz
?# Asset Control
?# Energy Saver feature for Energy Star®compliance
?# Macintosh-compatible timing with optional connector∗
?# USB Hub (1 upstream, 4 downstream)
?# Compliance with the following regulated specifications:
❏ Swedish MPR II 1990
❏ EPA ENERGY STAR®
❏ European Union CE Directives
❏ Swedish TCO 99 for all models
∗A Macintosh-compatible connector is not supplied with this monitor.

1-2 English
Part Number: 325603-001- Writer: Carol Benjamin Saved by: Alyce Klingler
Pages: 16 Words: 2796 Saved date: 10/27/99 5:20 PM File Name: P1100
✎Depending on the content of the screen, at times the shadows of
two small horizontal lines may appear on the screen. This is not
a defect and is normal for all aperture grille type displays. The
shadows are two damper wires that reduce the monitor's
susceptibility to vibration.
Universal Driver Manager
This monitor may require a graphics driver (and/or .INF file) that is
compatible with your computer’s graphics adapter. A CD-ROM
containing an .INF file is included with this monitor (see the section on
Information Files). Compaq has also created a Universal Driver
Manager (UDM) release that supports all graphics adapters found on
Compaq Deskpro and Compaq Workstation products. The UDM eases
graphics driver deployment across Compaq platforms ensuring cross-
compatibility and backward-compatibility. The resulting solution
enables customers to manage and control ongoing software maintenance
costs. The UDM is available on the Compaq Support Software CD for
Compaq Desktop, Portable, and Workstation Products and the Compaq
web site (www.compaq.com).
Information Files
This monitor includes a CD-ROM with two information files that should
be installed onto your computer—an .INF file and an .ICM file. The
.INF file defines monitor resources and provides specifications used by
Microsoft Windows 95/98 to install support software for certain
hardware devices. The .INF file ensures monitor compatibility and
optimization with your computer’s graphics adapter.
The .ICM file provides color matching consistency from monitor screen
to printer and is activated from within the graphics programs that have
this feature. To install these files on your computer, insert the Compaq
CD-ROM into the computer's CD tray and follow the instructions from
the menu that appears on the monitor screen. The CD-ROM is located in
the Program License Agreement packet. INF file updates are
downloadable by clicking on:
www.compaq.com/products/monitors/index.html

English 1-3
Part Number: 325603-001- Writer: Shauna Allison - Saved by: Lynette
Saved date: 10/27/99 5:18 PM - File Name: Ch1Fitt.doc
Setting Up the Monitor
To set up the monitor, ensure that the power is turned off to the monitor,
computer system, and other attached devices, then follow these steps:
1. Place the monitor in a convenient, well-ventilated location near
your computer.
2. Connect the monitor signal cable 3to one of the two 15-pin
connectors 4on the rear panel of the computer and tighten the
screws.
✎Be sure the signal cable aligns with the 15-pin connector. Do
not force the cable onto the connector or you may damage the
signal cable.
3. Connect one end of the monitor power cord 1to the connector
on the back of the monitor and the other end 2to an electrical
outlet that is easily accessible and close to the monitor.

1-4 English
Part Number: 325603-001- Writer: Carol Benjamin Saved by: Alyce Klingler
Pages: 16 Words: 2796 Saved date: 10/27/99 5:20 PM File Name: P1100
!WARNING: To reduce the risk of electric shock or damage
to your equipment:
„Do not disable the power cord grounding plug. The
grounding plug is an important safety feature.
?# Plug the power cord into a grounded (earthed) electrical
outlet that is easily accessible at all times.
„#Disconnect power from the monitor by unplugging the
power cord from the electrical outlet.
„#Do not place anything on power cords or cables.
Arrange them so that no one may accidentally step on or
trip over them. Do not pull on a cord or cable. When
unplugging from the electrical outlet, grasp the cord by
the plug.

English 1-5
Part Number: 325603-001- Writer: Shauna Allison - Saved by: Lynette
Saved date: 10/27/99 5:18 PM - File Name: Ch1Fitt.doc
Using USB Connectors
The base of the monitor has five Universal Serial Bus (USB) connectors.
Four of these connectors, 1,2,3,and 4, are for connecting USB
compatible devices such as a keyboard, mouse, or joystick to the hub.
USB connector 5is used to connect the USB signal cable to the
computer. The USB signal cable is included with the monitor.
The following are required to operate the USB hub:
?# Your computer must be fitted with a USB port.
?# Your computer must have Microsoft Windows 95 OSR2.1 or
later, or Microsoft Windows 98 as the operating system.

1-6 English
Part Number: 325603-001- Writer: Carol Benjamin Saved by: Alyce Klingler
Pages: 16 Words: 2796 Saved date: 10/27/99 5:20 PM File Name: P1100
Operating the Monitor
Front Panel Controls
No./Icon Control Function
1Reset Button Pressing this button resets the following items: Contrast,
brightness, size/center, geometry, screen, zoom, and
color. OSD Position, Color Mode, Control Lock, and
Language can not be reset.
2Auto Adjust Provides automatic horizontal and vertical centering and
sizing.
312Input/Select
Switch
Selects either video input 1 or 2.
4
Brightness Button Down arrow decreases brightness or is used to select
menu adjustment
5Brightness Button Up arrow Increases brightness or is used to select menu
adjustment.
6Menu Button Launches on-screen menus and selects the functions. Also,
exits menus and on-screen display.
7Contrast Button Left arrow decreases contrast or is used to adjust selected
OSD adjustment item.

English 1-7
Part Number: 325603-001- Writer: Shauna Allison - Saved by: Lynette
Saved date: 10/27/99 5:18 PM - File Name: Ch1Fitt.doc
Continued
8Contrast Button Right arrow increases contrast or is used to adjust selected
OSD adjustment item
9Power Button Turns the monitor on and off.
:LED Indicates monitor mode.
1. Green LED indicates monitor is turned on.
2. Alternating Amber/Green LED indicates
Standby/Suspend.
3. Amber LED indicates Sleep Mode.
;Light Sensor Automatically adjusts the monitor contrast depending on
the ambient light levels.

1-8 English
Part Number: 325603-001- Writer: Carol Benjamin Saved by: Alyce Klingler
Pages: 16 Words: 2796 Saved date: 10/27/99 5:20 PM File Name: P1100
On-Screen Display Settings
To adjust screen settings, press the Menu button 6to launch the on-
screen display (OSD). The OSD can be viewed in nine available
languages. The following menu shows the functions at each level:
Menu Level 1 Menu Level 2
Size/Center Horizontal Centering
Vertical Centering
Horizontal Sizing
Vertical Sizing
Zoom
Geometry Rotation
Pincushion
Pin Balance
Keystone
Key Balance
Convergence Horizontal Convergence
Vertical Convergence
Vertical Convergence Top
Vertical Convergence Bottom
Screen Landing Left Top
Landing Right Top
Landing Left Bottom
Landing Right Bottom
Moire Cancel
Color Easy - 5000/6500/9300/adjustable
Expert - RGB Gain, RGB Bias
Color Return - optimizes screen brilliance as CRT ages.
Language English
Francais
Deutsche
Espanol
Italiano
Nederlands
Svenska
Ðóññêèé (Russian)
(Japanese)
Option Degauss
OSD Horizontal Position
OSD Vertical Position
Control Lock
Light Sensor
Information* Model
Serial
Manufactured
* To get this data, press the Menu button for 5 seconds while the monitor picture is stable,