Compex WPQ618 Installation instructions

hardware guide - wpq618
Last Updated: 27/09/2021
hardware guide - WPQ618
1
Component Map
M.2 NGFF B Key Socket
with USB 3.0
2x 2.5Gbps Ethernet
Ports
IPQ6018 CPU
2.4/5GHz radio
2x SIM sockets
DC Jack
802.3at POE
Hardware Reset Button
SIM Switch Button
RJ45 Serial Port

hardware guide - WPQ618
2
Compex Systems Pte Ltd | www.compex.com.sg | ([phone] | [e-mail] | Last Updated: 27/09/2021 SL, LL, AT, GS
Copyright © Compex Systems. All rights reserved. COMPEX and the COMPEX logo, are registered trademarks of Compex Systems Pte. Ltd.
While every eort is made to ensure the information is accurate, Compex does not accept liability for any errors or mistakes that may arise.
All specications are subject to change without notice.
Power Requirements
DC Power 1x DC 12V for Main Board
Power Consumption 17.5W (Max)
Serial Interface Pin Assignment
Serial Interface
Pin Signal
1 DVDD_3V3
2 UART_TXD_CONN
3 UART_RXD_CONN
4 GND
JTAG Interface Pin Assignment
JTAG Interface
Pin Signal Pin Signal
1 VDD_1V8 2 VDD_1V8
3 JTAG_TRSTN 4 NC
5 JTAG_TDI 6 GND
7 JTAG_TMS 8 GND
9 JTAG_TCK 10 GND
11 PULL UP_1V8 12 GND
13 JTAG_TDO 14 GND
15 JTAG_SRSTN 16 GND
17 GND 18 GND
19 GND 20 GND
SIM Slot Pin Assignment
SIM Slot
Pin Signal
1 VCC
2 RST
3 CLK
4 CD
5 GND
6 NC
7 I/O
NGFF Slot 1 Pin Assignment
NGFF Slot with USB 3.0
Top Side Bottom Side
1 NC 2 VDD_3V7
3 GND 4 VDD_3V7
5 GND 6 FULL_Card_off
7 USB0_DP 8 WAN_DISABLE
9 USB0_DM 10 NC
11 GND
Mechanical Key B
21 NC 20 NC
23 NC 22 NC
25 NC 24 NC
27 GND 26 NC
29 USB0_SS_RXN 28 NC
31 USB0_SS_RXP 30 SIM1_RST
33 GND 32 SIM1_CLK
35 USB0_SS_TXN 34 SIM1_I/O
37 USB0_SS_TXP 36 SIM1_VCC
39 GND 38 NC
41 NC 40 SIM2_CD
43 NC 42 SIM2_I/O
45 GND 44 SIM2_CLK
47 NC 46 SIM2_RST
49 NC 48 SIM2_VCC
51 GND 50 NC
53 NC 52 NC
55 NC 54 NC
57 GND 56 NC
59 NC 58 NC
61 NC 60 NC
63 NC 62 NC
65 NC 64 NC
67 NC 66 SIM1_CD
69 NC 68 NC
71 GND 70 VDD_3V7
73 GND 72 VDD_3V7
75 NC 74 VDD_3V7
Ethernet Ports Pin Assignment
Ethernet LAN Port (RJ45 2.5Gbps)
Pin Signal Pin Signal
1 2.5G_CH0_P 2 2.5G_CH0_N
3 2.5G_CH1_P 4 2.5G_CH2_P
5 2.5G_CH2_N 6 2.5G_CH1_N
7 2.5G_CH3_P 8 2.5G_CH3_N

Federal Communications Commission (FCC) Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
RF exposure warning
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used
for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must
not be collocated or operating in conjunction with any other antenna or transmitter.

ISED
CAN ICES-003 (B)/NMB-003(B)
Canadian Compliance Statement This device complies with Industry Canada
license-exempt RSSs. Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes:
1. l’appareil ne doit pas produire de brouillage;
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si
le brouillage est susceptible d’en compromettre le fonctionnement.
Thisradiotransmitter(IC:7849A-WPQ618/Modelname:WPQ618)hasbeenapproved
by Industry Canada to operate with the antenna types listed below with the maximum
permissible gain indicated. Antenna types notincluded in this list, having again greater
than the maximum gain indicated for that type, are strictly prohibited for use with this
device.
Le présent émetteur radio (IC: 7849A-WPQ618 / Model name: WPQ618) a été
approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés
ci-dessous et ayant un gain admissible maximal. Les types d’antenne non inclus dans
cette liste ci-dessous et dont le gain est supérieur au gain maximal indiqué, sont
strictement interdits pour l’exploitation de l’émetteur.
Antenna Type
Frequency
Band (MHz)
TX
Paths
Max Antenna
Gain (dBi)
CDD Directional Gain (dBi)
For Power
For PSD
Omni
Antenna
2412 ~ 2462
2
8.0
8.0
11.01
5150 ~ 5850
2
5.0
5.0
8.01
Caution:
1. The device for operation in the band 5150–5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite
systems;
2. For devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the
equipment still complies with the e.i.r.p. limit;
3. For devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the band 5725-5850 MHz shall be such that the equipment still
complies with the e.i.r.p. limits as appropriate.

4. The high-power radars are allocated as primary users (i.e. priority users) of the
bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause
interference and/or damage to LE-LAN devices.
5. DFS (Dynamic Frequency Selection) products that operate in the bands 5250-
5350 MHz, 5470-5600MHz, and 5650-5725MHz.
Mise en garde:
1. Le dispositif destinéàêtre utilisédans la bande de fréquences 5150–5250 MHz
est destinéuniquement àune utilisation en intérieur afin de réduire le risque de
brouillage préjudiciable causépar les systèmes mobiles àsatellites dans le même
canal;
2. Pour les dispositifs avec une ou plusieurs antennes détachables, le gain
d'antenne maximal autorisépour les dispositifs des bandes 5250-5350 MHz et
5470-5725 MHz doit être tel que l'équipement respecte encore les normes e.i.r.p.
limite;
3. Pour les dispositifs avec une ou plusieurs antennes détachables, le gain
d'antenne maximal autorisépour les dispositifs de la bande 5725-5850 MHz doit
être tel que l'équipement soit toujours conforme àla norme e.i.r.p. limites, le cas
échéant.
4. Les radars àhaute puissance sont attribués en tant qu'utilisateurs principaux
(utilisateurs prioritaires) des bandes 5250-5350 MHz et 5650-5850 MHz et que
ces radars pourraient causer des interférences et / ou des dommages aux
dispositifs LE-LAN.
5. Produits DFS (Dynamic Frequency Selection) fonctionnant dans les bandes de
fréquences 5250-533 MHz, 5470-5600 MHz et 5650-5725 MHz.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator and your body.
Déclarationd'exposition aux radiations:
Cetéquipementestconforme aux limitesd'exposition aux rayonnements IC
établies pour un environnement non contrôlé. Cetéquipementdoitêtreinstalléet
utiliséavec un minimum de 20cm de distance entre la source de rayonnement
et votre corps.