Conair NC01RC User guide
IMPORTANT SAFETY
INSTRUCTIONS
THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE.
WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE TAKEN, INCLUDING
THE FOLLOWING:
READ ALL INSTRUCTIONS
BEFORE USING
KEEP AWAY FROM WATER
DANGER – To reduce the risk of elec-
trocution:
1. Always unplug this appliance immediately
after using.
2. Do not use while bathing.
3. Do not place or store appliance where it can
fall or be pulled into a tub or sink.
4. Do not place in or drop into water or other
liquid.
5. Do not reach for an appliance that has fallen
into water. Unplug immediately.
WARNING – To reduce the risk of
burns, electrocution, fire, or injury to persons:
1. Read all instructions before using the
appliance.
2. To protect against electrical hazards,
do not use while bathing or in the shower.
3. Close supervision is necessary when any
appliance is used by or near children or by
individuals with certain disabilities.
4. Unplug the appliance from outlet when not
in use and before cleaning. Do not leave
appliance unattended when it is plugged
in. Keep cord away from heated surfaces.
5. Do not operate this appliance with a
damaged cord or plug or if the appliance
malfunctions or has been dropped or
damaged in any manner. Return
appliance to nearest service facility for
examination, electrical or mechanical
adjustment, or repair. No repairs should
be attempted by the consumer.
6. Use appliance only for intended use as
described in this instruction book. The
use of attachments not recommended or
sold by Conair may cause hazards.
7. Do not use outdoors or operate where
aerosol (spray) products are being used,
or where oxygen is being administered.
8. Do not use on a soft surface such as a bed,
where openings may be blocked.
9. Do not place or store appliance where it
can fall or be pulled into a tub or sink.
10. Do not place in or drop into water or other
liquid.
11. If an appliance falls into water, unplug it
immediately. Do not reach into the water.
Use on any 120 volt 60 hertz AC electric
outlet (ordinary household current). Do
not use it on any other electrical outlet.
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
1. Your Complete Nail Care Centre operates on an
AC adapter. Adapter can be plugged into the
housing to operate the nail dryer or to recharge
the power handle; adapter can also be used to
operate the power handle directly by plugging
into the bottom of the handle.
2. The power handle has two interchangeable
heads. The rotary head works with round attach-
ments that spin in a circular motion and the
linear head works with rectangular plates that
move in a back-and-forth motion. The rotary
head is already attached to the power handle.
Pull power handle up to remove from the
attachment tray.
3. To change heads: twist the head in a counter-
clockwise motion and pull up; head comes off.
Gently push other head onto plastic base and
twist slightly with clockwise motion until head
clicks into secure position.
4. To attach discs or plates: To attach discs or cones
to the rotary head, insert metal post of disc into
the white plastic tube of head and gently push
down. To attach plates to the linear head, match
up rounded end of plate with round end of head
and snap plate onto head. To remove attach
ments, simply pull off.
5. Your Complete Nail Care Centre contains a
number of attachments. The coarser discs and
plates are ideal for shaping and eliminating
ragged edges for a clean finish. The finer discs,
cones and plates smooth unsightly ridges. The
polishing cone and disc provide the flawless
smooth surface needed for nail polish appli-
cations and help polish nails to a healthy-
looking luster.
6. To soften nails and cuticles before a manicure,
pull out the manicurist’s dish, fill it with warm
soapy water and soak your finger tips for a few
minutes. Dry your hands thoroughly before
using the power handle and attachments.
7. After you have attached a head and an
appropriate attachment to the power handle, turn
the power handle “on” and carefully start
shaping, smoothing or polishing your nails. You
can vary the speed at which the attachment
moves by turning the speed dial. Slower speeds
give you more control over the filing procedure.
8. Your power handle also features a light to give
you additional illumination when working on
a nail.
9. Your Complete Nail Care Centre includes a nail
dryer which will help shorten fresh nail polish
drying time. Simply insert your hand into the nail
dryer, pushing down slightly. That will start the
nail dryer. Check nails after a few minutes to see
if polish is dry.
10. After using the Complete Nail Care Centre
several times, you will find the attachment and
speed combinations that give you the results
you desire.
MANICURE
1. Soak your nails in warm soapy water, then
dry thoroughly.
2. Decide on the nail shape you want. The three
most common nail shapes are round, square, or
square with rounded edges.
3. Use the Smoothing Disc/Plate to smooth the
edges of each nail. Then use the rounded end
of the Cuticle Shaper to gently push the cuticles
away from the nail plate. If desired, massage
lotion or cream into the cuticle to help soften
cuticle and promote healthy nails. Unwanted
rough or hard skin can be reduced by using the
Sapphire Cones and/or a Smoothing Disc. The
side of the pointed Sapphire Cone may be used
to carefully remove areas of hard skin beside the
nail, using care not to damage the nail wall. In
cases where ridges and furrows are present, the
Smoothing Disc/Plate can be used to gently and
carefully reduce the unevenness, using short
intermittent strokes. This is not recommended
more than once every eight weeks.
4. To give nails a healthy natural look, use the
Polishing Disc or Cone, maximum of 30 seconds
per nail, taking care to avoid the cuticle.
5. Finish your manicure by using a moisturizing
lotion or cream.
PEDICURE
1. Soak your feet for five minutes in warm, soapy
water and dry thoroughly.
2. Use the Smoothing Disc/Plate to reduce the
06CN1438_NC01RC_IB.indd 1 1/30/07 3:25:54 PM
length of the nail. Toe nails should be filed
straight across to avoid ingrown toe nails. Use a
fine Smoothing Disc/Plate on a low speed as a
finishing touch to the edges.
3. To reduce calluses, rough, or hard skin, use
the Sapphire Cones or a Smoothing Disc/Plate.
The thickness or dead skin can be reduced by
using the side of the Sapphire Cones. Where
ridges and furrows are present, the Smoothing
Disc can also be used to gently and carefully
reduce the unevenness, using short intermittent
strokes. This is not recommended more than
once every eight weeks.
4. Finish your pedicure by using a moisturizing
lotion or cream.
MAINTENANCE
Your nail care centre is designed for household use and
is virtually maintenance-free. No lubrication is needed.
If cleaning becomes necessary, disconnect the appli-
ance from the power source and wipe exterior with a
cloth.
If any abnormal condition occurs, unplug the nail care
centre, allow it to cool, and return it to an authorized
service centre for repair.
CHARGING
The Conair Professional Nail Care System should be
charged using only the charger supplied. Ensure that
the switch on the handle is in the “off” position. Connect
the appliance to the charger by inserting the small plug
at the end of the charger lead into the corresponding
socket in the end of the handle. Plug the charger into
the main wall socket. Allow the handle to charge for 16
hours. To preserve the longest possible life of the re-
chargeable cells, it is better not to leave the appliance
on charge for more than 24 consecutive hours.
CORdEd USE
1) Ensure that the handle is switched off.
2) Insert the small plug at the end of the charger
lead into the corresponding socket in the end
of the handle. Plug the charger into the main wall
socket. Wait for one minute, then switch on.
IMPORTANT! Do not use the appliance in this
mode for more than 20 minutes.
GETTING TO KNOW YOUR
COMPLETE NAIL CARE SYSTEM
1. Rechargeable Power Handle works corded
or cordless
2. Variable Speed Control
3. LED Indicator
4. On/Off Switch
5. Light
6. Nail Dryer
7. Manicurist’s Dish
8. Cuticle Shaper
9. Linear Head
10. Rotary Head
11. Metal smoothing plate
12. Metal Shaping Plate
13. Buffing Plate
14. Smoothing Plate
15. Felt Cone
16. Large Sapphire Cone *
17. Smoothing Disc
18. Shaping Disc
19. Small Sapphire Cone *
20. Medium Sapphire Cone *
21. Buffing Disc
Everyone knows that electricity and water are a
dangerous combination. But did you know that an elec-
tric appliance is still electrically live even if the switch
is off?
If the plug is in, the power is on. So when you are not
using your appliances, keep them unplugged.
ALWAYS UNPLUG
SMALL APPLIANCES
A Public Service Ad from the Association of Home
Appliance Manufacturers and Underwriters Laboratories, Inc.
STORAGE
Disconnect from electrical outlet. Place nail care
centre in cool, dry area out of reach of children, where
it will not be damaged. Handle cord carefully for longer
life; do not jerk or strain at plug connections, or wrap
cord around unit for storage. This could cause dam-
age to the cord or a short circuit. To store unit, coil cord
loosely.
LIMITED ONE YEAR WARRANTY
Conair will repair or replace (at our option) your
unit free of charge for 12 months from the date of
purchase if the appliance is defective in workmanship
or materials.
To obtain service under this warranty, return the
defective product to the service centre listed below
that is nearest you, together with your purchase receipt
and $5.50 for postage and handling. In the absence
of a purchase receipt, the warranty period shall be
12 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED
IN DURATION TO THE 12 MONTH DURATION
OF THIS WRITTEN, LIMITED WARRANTY.
IN NO EVENT SHALL CONAIR BE LIABLE FOR
ANY SPECIAL, INCIDENTAL, OR CON-
SEQUENTIAL DAMAGES FOR BREACH OF
THIS OR ANY OTHER WARRANTY, EXPRESS
OR IMPLIED, WHATSOEVER.
This warranty gives you specific legal rights, and you
may also have other rights, which vary from province
to province.
* for acrylic nails
WARNING:
IF YOU THINK
THE POWER IS OFF
WHEN THE SWITCH
IS OFF,
YOU’RE WRONG.
KEEP AWAY FROM WATER
SERVICE CENTRE:
Conair Consumer Products Inc.
100 Conair Parkway,
Woodbridge, Ontario. L4H 0L2
1-800-472-7606
Consumer Call Centre E-mail:
Consumer_Canada@Conair.com
www.conaircanada.ca
©2006 CONAIR CONSUMER PRODUCTS INC.
06CN1438 IB-7329
INSTRUCTION & STYlING GUIdE
For your safety & continued
enjoyment of this product,
always read the instruction book
carefully before using.
NC01RC MOdElS
1
2
345
6
7
8
9
10
11 12
13 14
15
16
17 18
19 20
21
The CompleTe
Nail CARE
CenTre
06CN1438_NC01RC_IB.indd 2 1/30/07 3:25:56 PM
IMPORTANT SAFETY
INSTRUCTIONS
THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE.
WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE TAKEN, INCLUDING
THE FOLLOWING:
READ ALL INSTRUCTIONS
BEFORE USING
KEEP AWAY FROM WATER
DANGER – To reduce the risk of elec-
trocution:
1. Always unplug this appliance immediately
after using.
2. Do not use while bathing.
3. Do not place or store appliance where it can
fall or be pulled into a tub or sink.
4. Do not place in or drop into water or other
liquid.
5. Do not reach for an appliance that has fallen
into water. Unplug immediately.
WARNING – To reduce the risk of
burns, electrocution, fire, or injury to persons:
1. Read all instructions before using the
appliance.
2. To protect against electrical hazards,
do not use while bathing or in the shower.
3. Close supervision is necessary when any
appliance is used by or near children or by
individuals with certain disabilities.
4. Unplug the appliance from outlet when not
in use and before cleaning. Do not leave
appliance unattended when it is plugged
in. Keep cord away from heated surfaces.
5. Do not operate this appliance with a
damaged cord or plug or if the appliance
malfunctions or has been dropped or
damaged in any manner. Return
appliance to nearest service facility for
examination, electrical or mechanical
adjustment, or repair. No repairs should
be attempted by the consumer.
6. Use appliance only for intended use as
described in this instruction book. The
use of attachments not recommended or
sold by Conair may cause hazards.
7. Do not use outdoors or operate where
aerosol (spray) products are being used,
or where oxygen is being administered.
8. Do not use on a soft surface such as a bed,
where openings may be blocked.
9. Do not place or store appliance where it
can fall or be pulled into a tub or sink.
10. Do not place in or drop into water or other
liquid.
11. If an appliance falls into water, unplug it
immediately. Do not reach into the water.
Use on any 120 volt 60 hertz AC electric
outlet (ordinary household current). Do
not use it on any other electrical outlet.
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
1. Your Complete Nail Care Centre operates on an
AC adapter. Adapter can be plugged into the
housing to operate the nail dryer or to recharge
the power handle; adapter can also be used to
operate the power handle directly by plugging
into the bottom of the handle.
2. The power handle has two interchangeable
heads. The rotary head works with round attach-
ments that spin in a circular motion and the
linear head works with rectangular plates that
move in a back-and-forth motion. The rotary
head is already attached to the power handle.
Pull power handle up to remove from the
attachment tray.
3. To change heads: twist the head in a counter-
clockwise motion and pull up; head comes off.
Gently push other head onto plastic base and
twist slightly with clockwise motion until head
clicks into secure position.
4. To attach discs or plates: To attach discs or cones
to the rotary head, insert metal post of disc into
the white plastic tube of head and gently push
down. To attach plates to the linear head, match
up rounded end of plate with round end of head
and snap plate onto head. To remove attach
ments, simply pull off.
5. Your Complete Nail Care Centre contains a
number of attachments. The coarser discs and
plates are ideal for shaping and eliminating
ragged edges for a clean finish. The finer discs,
cones and plates smooth unsightly ridges. The
polishing cone and disc provide the flawless
smooth surface needed for nail polish appli-
cations and help polish nails to a healthy-
looking luster.
6. To soften nails and cuticles before a manicure,
pull out the manicurist’s dish, fill it with warm
soapy water and soak your finger tips for a few
minutes. Dry your hands thoroughly before
using the power handle and attachments.
7. After you have attached a head and an
appropriate attachment to the power handle, turn
the power handle “on” and carefully start
shaping, smoothing or polishing your nails. You
can vary the speed at which the attachment
moves by turning the speed dial. Slower speeds
give you more control over the filing procedure.
8. Your power handle also features a light to give
you additional illumination when working on
a nail.
9. Your Complete Nail Care Centre includes a nail
dryer which will help shorten fresh nail polish
drying time. Simply insert your hand into the nail
dryer, pushing down slightly. That will start the
nail dryer. Check nails after a few minutes to see
if polish is dry.
10. After using the Complete Nail Care Centre
several times, you will find the attachment and
speed combinations that give you the results
you desire.
MANICURE
1. Soak your nails in warm soapy water, then
dry thoroughly.
2. Decide on the nail shape you want. The three
most common nail shapes are round, square, or
square with rounded edges.
3. Use the Smoothing Disc/Plate to smooth the
edges of each nail. Then use the rounded end
of the Cuticle Shaper to gently push the cuticles
away from the nail plate. If desired, massage
lotion or cream into the cuticle to help soften
cuticle and promote healthy nails. Unwanted
rough or hard skin can be reduced by using the
Sapphire Cones and/or a Smoothing Disc. The
side of the pointed Sapphire Cone may be used
to carefully remove areas of hard skin beside the
nail, using care not to damage the nail wall. In
cases where ridges and furrows are present, the
Smoothing Disc/Plate can be used to gently and
carefully reduce the unevenness, using short
intermittent strokes. This is not recommended
more than once every eight weeks.
4. To give nails a healthy natural look, use the
Polishing Disc or Cone, maximum of 30 seconds
per nail, taking care to avoid the cuticle.
5. Finish your manicure by using a moisturizing
lotion or cream.
PEDICURE
1. Soak your feet for five minutes in warm, soapy
water and dry thoroughly.
2. Use the Smoothing Disc/Plate to reduce the
06CN1438_NC01RC_IB.indd 1 1/30/07 3:25:54 PM
length of the nail. Toe nails should be filed
straight across to avoid ingrown toe nails. Use a
fine Smoothing Disc/Plate on a low speed as a
finishing touch to the edges.
3. To reduce calluses, rough, or hard skin, use
the Sapphire Cones or a Smoothing Disc/Plate.
The thickness or dead skin can be reduced by
using the side of the Sapphire Cones. Where
ridges and furrows are present, the Smoothing
Disc can also be used to gently and carefully
reduce the unevenness, using short intermittent
strokes. This is not recommended more than
once every eight weeks.
4. Finish your pedicure by using a moisturizing
lotion or cream.
MAINTENANCE
Your nail care centre is designed for household use and
is virtually maintenance-free. No lubrication is needed.
If cleaning becomes necessary, disconnect the appli-
ance from the power source and wipe exterior with a
cloth.
If any abnormal condition occurs, unplug the nail care
centre, allow it to cool, and return it to an authorized
service centre for repair.
CHARGING
The Conair Professional Nail Care System should be
charged using only the charger supplied. Ensure that
the switch on the handle is in the “off” position. Connect
the appliance to the charger by inserting the small plug
at the end of the charger lead into the corresponding
socket in the end of the handle. Plug the charger into
the main wall socket. Allow the handle to charge for 16
hours. To preserve the longest possible life of the re-
chargeable cells, it is better not to leave the appliance
on charge for more than 24 consecutive hours.
CORdEd USE
1) Ensure that the handle is switched off.
2) Insert the small plug at the end of the charger
lead into the corresponding socket in the end
of the handle. Plug the charger into the main wall
socket. Wait for one minute, then switch on.
IMPORTANT! Do not use the appliance in this
mode for more than 20 minutes.
GETTING TO KNOW YOUR
COMPLETE NAIL CARE SYSTEM
1. Rechargeable Power Handle works corded
or cordless
2. Variable Speed Control
3. LED Indicator
4. On/Off Switch
5. Light
6. Nail Dryer
7. Manicurist’s Dish
8. Cuticle Shaper
9. Linear Head
10. Rotary Head
11. Metal smoothing plate
12. Metal Shaping Plate
13. Buffing Plate
14. Smoothing Plate
15. Felt Cone
16. Large Sapphire Cone *
17. Smoothing Disc
18. Shaping Disc
19. Small Sapphire Cone *
20. Medium Sapphire Cone *
21. Buffing Disc
Everyone knows that electricity and water are a
dangerous combination. But did you know that an elec-
tric appliance is still electrically live even if the switch
is off?
If the plug is in, the power is on. So when you are not
using your appliances, keep them unplugged.
ALWAYS UNPLUG
SMALL APPLIANCES
A Public Service Ad from the Association of Home
Appliance Manufacturers and Underwriters Laboratories, Inc.
STORAGE
Disconnect from electrical outlet. Place nail care
centre in cool, dry area out of reach of children, where
it will not be damaged. Handle cord carefully for longer
life; do not jerk or strain at plug connections, or wrap
cord around unit for storage. This could cause dam-
age to the cord or a short circuit. To store unit, coil cord
loosely.
LIMITED ONE YEAR WARRANTY
Conair will repair or replace (at our option) your
unit free of charge for 12 months from the date of
purchase if the appliance is defective in workmanship
or materials.
To obtain service under this warranty, return the
defective product to the service centre listed below
that is nearest you, together with your purchase receipt
and $5.50 for postage and handling. In the absence
of a purchase receipt, the warranty period shall be
12 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED
IN DURATION TO THE 12 MONTH DURATION
OF THIS WRITTEN, LIMITED WARRANTY.
IN NO EVENT SHALL CONAIR BE LIABLE FOR
ANY SPECIAL, INCIDENTAL, OR CON-
SEQUENTIAL DAMAGES FOR BREACH OF
THIS OR ANY OTHER WARRANTY, EXPRESS
OR IMPLIED, WHATSOEVER.
This warranty gives you specific legal rights, and you
may also have other rights, which vary from province
to province.
* for acrylic nails
WARNING:
IF YOU THINK
THE POWER IS OFF
WHEN THE SWITCH
IS OFF,
YOU’RE WRONG.
KEEP AWAY FROM WATER
SERVICE CENTRE:
Conair Consumer Products Inc.
100 Conair Parkway,
Woodbridge, Ontario. L4H 0L2
1-800-472-7606
Consumer Call Centre E-mail:
Consumer_Canada@Conair.com
www.conaircanada.ca
©2006 CONAIR CONSUMER PRODUCTS INC.
06CN1438 IB-7329
INSTRUCTION & STYlING GUIdE
For your safety & continued
enjoyment of this product,
always read the instruction book
carefully before using.
NC01RC MOdElS
1
2
345
6
7
8
9
10
11 12
13 14
15
16
17 18
19 20
21
The CompleTe
Nail CARE
CenTre
06CN1438_NC01RC_IB.indd 2 1/30/07 3:25:56 PM
IMPORTANT SAFETY
INSTRUCTIONS
THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE.
WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE TAKEN, INCLUDING
THE FOLLOWING:
READ ALL INSTRUCTIONS
BEFORE USING
KEEP AWAY FROM WATER
DANGER – To reduce the risk of elec-
trocution:
1. Always unplug this appliance immediately
after using.
2. Do not use while bathing.
3. Do not place or store appliance where it can
fall or be pulled into a tub or sink.
4. Do not place in or drop into water or other
liquid.
5. Do not reach for an appliance that has fallen
into water. Unplug immediately.
WARNING – To reduce the risk of
burns, electrocution, fire, or injury to persons:
1. Read all instructions before using the
appliance.
2. To protect against electrical hazards,
do not use while bathing or in the shower.
3. Close supervision is necessary when any
appliance is used by or near children or by
individuals with certain disabilities.
4. Unplug the appliance from outlet when not
in use and before cleaning. Do not leave
appliance unattended when it is plugged
in. Keep cord away from heated surfaces.
5. Do not operate this appliance with a
damaged cord or plug or if the appliance
malfunctions or has been dropped or
damaged in any manner. Return
appliance to nearest service facility for
examination, electrical or mechanical
adjustment, or repair. No repairs should
be attempted by the consumer.
6. Use appliance only for intended use as
described in this instruction book. The
use of attachments not recommended or
sold by Conair may cause hazards.
7. Do not use outdoors or operate where
aerosol (spray) products are being used,
or where oxygen is being administered.
8. Do not use on a soft surface such as a bed,
where openings may be blocked.
9. Do not place or store appliance where it
can fall or be pulled into a tub or sink.
10. Do not place in or drop into water or other
liquid.
11. If an appliance falls into water, unplug it
immediately. Do not reach into the water.
Use on any 120 volt 60 hertz AC electric
outlet (ordinary household current). Do
not use it on any other electrical outlet.
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
1. Your Complete Nail Care Centre operates on an
AC adapter. Adapter can be plugged into the
housing to operate the nail dryer or to recharge
the power handle; adapter can also be used to
operate the power handle directly by plugging
into the bottom of the handle.
2. The power handle has two interchangeable
heads. The rotary head works with round attach-
ments that spin in a circular motion and the
linear head works with rectangular plates that
move in a back-and-forth motion. The rotary
head is already attached to the power handle.
Pull power handle up to remove from the
attachment tray.
3. To change heads: twist the head in a counter-
clockwise motion and pull up; head comes off.
Gently push other head onto plastic base and
twist slightly with clockwise motion until head
clicks into secure position.
4. To attach discs or plates: To attach discs or cones
to the rotary head, insert metal post of disc into
the white plastic tube of head and gently push
down. To attach plates to the linear head, match
up rounded end of plate with round end of head
and snap plate onto head. To remove attach
ments, simply pull off.
5. Your Complete Nail Care Centre contains a
number of attachments. The coarser discs and
plates are ideal for shaping and eliminating
ragged edges for a clean finish. The finer discs,
cones and plates smooth unsightly ridges. The
polishing cone and disc provide the flawless
smooth surface needed for nail polish appli-
cations and help polish nails to a healthy-
looking luster.
6. To soften nails and cuticles before a manicure,
pull out the manicurist’s dish, fill it with warm
soapy water and soak your finger tips for a few
minutes. Dry your hands thoroughly before
using the power handle and attachments.
7. After you have attached a head and an
appropriate attachment to the power handle, turn
the power handle “on” and carefully start
shaping, smoothing or polishing your nails. You
can vary the speed at which the attachment
moves by turning the speed dial. Slower speeds
give you more control over the filing procedure.
8. Your power handle also features a light to give
you additional illumination when working on
a nail.
9. Your Complete Nail Care Centre includes a nail
dryer which will help shorten fresh nail polish
drying time. Simply insert your hand into the nail
dryer, pushing down slightly. That will start the
nail dryer. Check nails after a few minutes to see
if polish is dry.
10. After using the Complete Nail Care Centre
several times, you will find the attachment and
speed combinations that give you the results
you desire.
MANICURE
1. Soak your nails in warm soapy water, then
dry thoroughly.
2. Decide on the nail shape you want. The three
most common nail shapes are round, square, or
square with rounded edges.
3. Use the Smoothing Disc/Plate to smooth the
edges of each nail. Then use the rounded end
of the Cuticle Shaper to gently push the cuticles
away from the nail plate. If desired, massage
lotion or cream into the cuticle to help soften
cuticle and promote healthy nails. Unwanted
rough or hard skin can be reduced by using the
Sapphire Cones and/or a Smoothing Disc. The
side of the pointed Sapphire Cone may be used
to carefully remove areas of hard skin beside the
nail, using care not to damage the nail wall. In
cases where ridges and furrows are present, the
Smoothing Disc/Plate can be used to gently and
carefully reduce the unevenness, using short
intermittent strokes. This is not recommended
more than once every eight weeks.
4. To give nails a healthy natural look, use the
Polishing Disc or Cone, maximum of 30 seconds
per nail, taking care to avoid the cuticle.
5. Finish your manicure by using a moisturizing
lotion or cream.
PEDICURE
1. Soak your feet for five minutes in warm, soapy
water and dry thoroughly.
2. Use the Smoothing Disc/Plate to reduce the
06CN1438_NC01RC_IB.indd 1 1/30/07 3:25:54 PM
length of the nail. Toe nails should be filed
straight across to avoid ingrown toe nails. Use a
fine Smoothing Disc/Plate on a low speed as a
finishing touch to the edges.
3. To reduce calluses, rough, or hard skin, use
the Sapphire Cones or a Smoothing Disc/Plate.
The thickness or dead skin can be reduced by
using the side of the Sapphire Cones. Where
ridges and furrows are present, the Smoothing
Disc can also be used to gently and carefully
reduce the unevenness, using short intermittent
strokes. This is not recommended more than
once every eight weeks.
4. Finish your pedicure by using a moisturizing
lotion or cream.
MAINTENANCE
Your nail care centre is designed for household use and
is virtually maintenance-free. No lubrication is needed.
If cleaning becomes necessary, disconnect the appli-
ance from the power source and wipe exterior with a
cloth.
If any abnormal condition occurs, unplug the nail care
centre, allow it to cool, and return it to an authorized
service centre for repair.
CHARGING
The Conair Professional Nail Care System should be
charged using only the charger supplied. Ensure that
the switch on the handle is in the “off” position. Connect
the appliance to the charger by inserting the small plug
at the end of the charger lead into the corresponding
socket in the end of the handle. Plug the charger into
the main wall socket. Allow the handle to charge for 16
hours. To preserve the longest possible life of the re-
chargeable cells, it is better not to leave the appliance
on charge for more than 24 consecutive hours.
CORdEd USE
1) Ensure that the handle is switched off.
2) Insert the small plug at the end of the charger
lead into the corresponding socket in the end
of the handle. Plug the charger into the main wall
socket. Wait for one minute, then switch on.
IMPORTANT! Do not use the appliance in this
mode for more than 20 minutes.
GETTING TO KNOW YOUR
COMPLETE NAIL CARE SYSTEM
1. Rechargeable Power Handle works corded
or cordless
2. Variable Speed Control
3. LED Indicator
4. On/Off Switch
5. Light
6. Nail Dryer
7. Manicurist’s Dish
8. Cuticle Shaper
9. Linear Head
10. Rotary Head
11. Metal smoothing plate
12. Metal Shaping Plate
13. Buffing Plate
14. Smoothing Plate
15. Felt Cone
16. Large Sapphire Cone *
17. Smoothing Disc
18. Shaping Disc
19. Small Sapphire Cone *
20. Medium Sapphire Cone *
21. Buffing Disc
Everyone knows that electricity and water are a
dangerous combination. But did you know that an elec-
tric appliance is still electrically live even if the switch
is off?
If the plug is in, the power is on. So when you are not
using your appliances, keep them unplugged.
ALWAYS UNPLUG
SMALL APPLIANCES
A Public Service Ad from the Association of Home
Appliance Manufacturers and Underwriters Laboratories, Inc.
STORAGE
Disconnect from electrical outlet. Place nail care
centre in cool, dry area out of reach of children, where
it will not be damaged. Handle cord carefully for longer
life; do not jerk or strain at plug connections, or wrap
cord around unit for storage. This could cause dam-
age to the cord or a short circuit. To store unit, coil cord
loosely.
LIMITED ONE YEAR WARRANTY
Conair will repair or replace (at our option) your
unit free of charge for 12 months from the date of
purchase if the appliance is defective in workmanship
or materials.
To obtain service under this warranty, return the
defective product to the service centre listed below
that is nearest you, together with your purchase receipt
and $5.50 for postage and handling. In the absence
of a purchase receipt, the warranty period shall be
12 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED
IN DURATION TO THE 12 MONTH DURATION
OF THIS WRITTEN, LIMITED WARRANTY.
IN NO EVENT SHALL CONAIR BE LIABLE FOR
ANY SPECIAL, INCIDENTAL, OR CON-
SEQUENTIAL DAMAGES FOR BREACH OF
THIS OR ANY OTHER WARRANTY, EXPRESS
OR IMPLIED, WHATSOEVER.
This warranty gives you specific legal rights, and you
may also have other rights, which vary from province
to province.
* for acrylic nails
WARNING:
IF YOU THINK
THE POWER IS OFF
WHEN THE SWITCH
IS OFF,
YOU’RE WRONG.
KEEP AWAY FROM WATER
SERVICE CENTRE:
Conair Consumer Products Inc.
100 Conair Parkway,
Woodbridge, Ontario. L4H 0L2
1-800-472-7606
Consumer Call Centre E-mail:
Consumer_Canada@Conair.com
www.conaircanada.ca
©2006 CONAIR CONSUMER PRODUCTS INC.
06CN1438 IB-7329
INSTRUCTION & STYlING GUIdE
For your safety & continued
enjoyment of this product,
always read the instruction book
carefully before using.
NC01RC MOdElS
1
2
345
6
7
8
9
10
11 12
13 14
15
16
17 18
19 20
21
The CompleTe
Nail CARE
CenTre
06CN1438_NC01RC_IB.indd 2 1/30/07 3:25:56 PM
Table of contents
