Continental Refrigerator ACCM User manual

WARRANTY
The customer shall benefit from the legal warranty against latent defects as specified in sections 1641 to 1649 of
the Belgian Civil Code if the latent defect exists at the time of delivery and if the latent defect makes the unit unfit
for the use for which it was designed or substantially reduces its use. Latent defects must be notified by registered
letter to Continental within one month from the time the customer discovers it or ought reasonably to have
discovered it. If the customer is a consumer, Continental shall be liable to the customer for any non-conformity
which exists at delivery and appears within two years thereof. Any non-conformity shall be notified by registered
letter to Continental within one month from the time the customer discovers it.
DISCLAIMER
The information in this document is subject to change without notice and does not represent a commitment on
the part of the vendor. No warranty or representation, either expressed or implied, is made with respect of quality,
accuracy or fitness for any particular purpose of this document. Without written permission from Continental, any
forms of reproduction, spreading, distribution are prohibited. Continental reserves the rights to modify or improve
the product without any prior notification. In no event will the supplier be liable for direct, indirect or special,
incidental or consequential damages arising out of the user or inability to use this product or documentation, even
if advised of the possibility of such damages. This document contains materials protected by copyright.
BLUETOOTH
The Bluetooth® word mark and logos are owned by the Bluetooth® SIG, Inc. and any use of such marks by
Continental is under license. Other trademarks and trade names are those of their respective owners.
CE
Hereby, Continental declares that this Car & Connected Car Module is compliant with essential requirements and
other relevant provisions of directive 2014/53/EU. The ACCM can be operated in at least one Member State
without infringing applicable requirements on the use of a radio spectrum
FCC (FEDERAL COMMUNICATIONS COMMISSION)
WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is
made. The device complies with Part 15 of FCC’s rules. Operation is subject to the following two conditions: (i) this
device may not cause harmful interference and (ii) this device must accept any interference received, including
interference that may cause undesirable operation.
MANUAL REQUIREMENTS ACCORDING 15.19/RSS-GEN
This device complies with Part 15 of the FCC Rules [and with Industry Canada licence-exempt RSS standard(s)].
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
FCC RF EXPOSURE REQUIREMENTS
This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
CORRECT DISPOSAL OF THIS PRODUCT (WASTE ELECTRICAL AND ELECTRONICS EQUIPMENT)
This marking shown on the product or its literature indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly.
COPYRIGHTS
Copyright © 2015 Continental. All rights reserved. No part of this manual may be reproduced or transmitted in
any means or for any purpose without the express written content of Continental. All trademarks, product names
appearing in this document are registered property of their respective owners.
Access and Connected Car Module (ACCM)
& Access and Connected Car Module PLUS (ACCM+)
INSTALLATION GUIDE (June 2021)
INTRODUCTION
Continental is a virtual key enabler. the Car & Connected Car Module - ACCM and the Car & Connected Car Module
PLUS –ACCM+ allow vehicle access, authorization to start and vehicle data for any vehicle fleet management type
Content of the box
Specification
1 ACCM or ACCM+
Electric Power 12Vcc
Consumption in stand-by mode < 8 mA
Operating temperature - 25°C ≈ + 55°C
Dimensions 131.6 x 61 x 37.6 mm
Weight 130g
Data transmission Bluetooth and LTE (US version only)
1 Power cable (OBDII connector)
ANTENNA FREQUENCY AND MAX POWER
For ACCM + only:
Communication protocols
Antenna
Allowable
bands
Uplink and
Downlink
Frequencies
(MHz)
Max Power
(dBm)
BLE
2402 ~2480
4.08
4G LTE
North
America
LARA-R203
band 2
(1900MHz)
UL
1850 ~ 1910
23
DL
1930 ~ 1990
band 4
(1700MHz)
UL
1710 ~ 1755
DL
2110 ~ 2155
band12
(700MHz)
UL
699 ~ 716
DL
729 ~ 746
EMEA
LARA-R211
band 3
(1800MHz)
UL
1710 ~ 1785
DL
1805 ~ 1880
band 7
(2600MHz)
UL
2500 ~ 2570
DL
2620 ~ 2690
band 20
(800MHz)
UL
832 ~ 862
DL
791 ~ 821
Communication protocols
Frequencies (MHz)
Max Power ( dBm)
SRD
313.5 ~315.3
-22.5
SRD
433.5 ~ 434.3
-22.5
SRD
868 ~ 868.5
-20.5
SRD
902.3 ~ 903.3
-20.5
MANUAL REQUIREMENTS ACCORDING 15.21
Changes or modifications made to this equipment not expressly approved by Continental Automotive GnbH may
void the FCC authorization to operate this equipment.

BEFORE YOU BEGIN
•We advise our customers to have the ACCM fitted by a professional.
•Never remove the cover of the
ACCM or ACCM+ .
•Before you install the individual components, check that the installation area has been
selected in such a way that:
•The cable length is sufficient to connect later every element: power cable and antenna
(if necessary)
•for a car equipped with a keyless start system, the location where you plan to install the
ACCM must be within the reception area of the keyless system of the car. Use therefore the original
key and place it at the chosen installation area and check immediately that the engine can be started.
•Do not install any component in the airbag deployment area.
IMPORTANT REMARKS
•Placing the
ACCM or ACCM+ under or next to any large metal surface or an airbag could affect the
reception of the ACCM.
•With the keyless start system, the vehicle doors can be opened without need for the driver to physically
push a button on the key fob to lock or unlock the doors. To start or to stop the engine, there is no need to insert
a key in the barrel to turn on the ignition.
•Installation steps 1 and 2 (see below) must only be performed for cars not equipped with a keyless start
system. If the car is equipped with a keyless system, go directly to step 3.
Disconnect the battery of the car.
1. Disassemble the shroud for easy access to the vehicle’s ignition switch. Pull the steering wheel in your
direction to its maximum.
2. Place the ring of the antenna around the vehicle’s ignition switch as shown below.
Fix and tape the ring around the ignition, excess cable can be taped together but may not be turned around (one
rotation maximum). When using the ring method for installing the
ACCM or ACCM+ the ring MUST be taped in
front of the factory receiver ring. It CAN NOT be on top of, or behind the factory receiver ring. See illustration
above. The antenna cable must follow existing steering column cables to avoid rupture while closing the shroud
or moving the steering wheel.
Reassemble the shroud.
+ -
WARNING
ContinentalS.Aanditsaffiliatesshouldnotbeheldliabletowardsend-usersforthirdpartiesprejudicecausedbymisusageofthe
product. We advise our customers to have the ACCM fitted by a professional.
•Do not install the ACCM or ACCM+ against a large metal surface in the car.
•Once the installation is completed, make sure that no cables are pinched or trapped.
•In case you would like to buy additional keys and have them programmed to the vehicle’s
immobilizer system in the future, some manufacturers require that all original keys are present in the
car to be able to get an additional key. It will be necessary that you participate in the coding of the new
key with a virtual key being active and connected to the car to perform the actions required by the
dealer.
•Continental is not responsible for the damage caused to the vehicle and/or accessories with
are the results of a non-respect of the instructions of this manual.
INSTALLATION STEPS:
/¶pPHWWHXUUpFHSWHXUH[HPSWGHOLFHQFHFRQWHQXGDQVOHSUpVHQWDSSDUHLOHVWFRQIRUPH
DX[& 15 G¶,QQRYDWLRQ6 FLHQFHVHW'pYHORSSHPHQWpFRQRPLTXH& DQDGDDSSOLFDEOHVDX[
DSSDUHLOVUDGLRH[HPSWVGHOLFHQFH/¶H[SORLWDWLRQHVWDXWRULVpHDX[GHX[FRQGLWLRQV
VXLYDQWHV
/¶DSSDUHLOQHGRLWSDVSURGXLUHGHEURXLOODJH
/¶DSSDUHLOGRLWDFFHSWHUWRXWEURXLOODJHUDGLRpOHFWULTXHVXELPr PHVLOHEURXLOODJH
HVWVXVFHSWLEOHG¶HQFRPSURPHWWUHOHIRQFWLRQQHPHQW
0$18$/5 ( 48,5 ( 0( 176 $& & 25 ',1*,& 5 8/( 6

3. Connect now the ACCM to the OBDII connector in the car. The OBD port is generally located in
the driver cabin, between the door and the steering column.
4. Place the NFC reader (optional) on the bottom left corner of the
windscreen. Use the provided sticker and tape to fix the reader on
the windscreen. Place the sticker on the windscreen and use the
tape to fix the reader on the sticker. The white side of the reader
must be faced to the car. For your convenience, you can also
decide to place the reader on the top left corner of the
windscreen.
5. Reconnect the vehicle battery.
6. Validate that the
ACCM or ACCM+ has a power connection (LEDs on side). You are now ready
to test the
ACCM with a virtual key on a smartphone equipped with the Continental mobile
application.
7. Fix the
ACCM or ACCM+ behind the dashboard.
Manufactured by: AMOTECH
Address: 5BL-1LOT, 380, Namdongseo-ro, Namdong-gu, Incheon, Korea 21629