Continental Refrigerator ContiPressureCheck Reference guide

1
Display Symbol Task
SET Switch between vehicle view and setup
Navigation between menu items and warn-
ing messages
OK Conirmation of the selected menu item
Switch between pressure, temperature
or target pressure indicator in the in the
vehicle view
Tool overview
These brief instructions are only intended to illustrate the most important oper-
ating steps and functions of the display and are a supplement to the actual user
manual. Make sure you also read the detailed user manual.
The current version of these instructions and further information can be obtained
from www.contipressurecheck.com/downloads
WARNING
Danger of accident!
Operating the display while driving can lead to accidents.
►Do not operate the display while driving.
►View the screen only if the traic situation allows.
An incorrectly or carelessly mounted display can impair driving safety!
►Before each journey, check the seating of the display and stability of the
holder.
Safety precautions
Brief instructions
ContiPressureCheckTM
Display and pressure control indicator
GB

2
Setup menu
Open the settings menu
Press the SET button to open the settings menu.
→
English
(100%)
bar / °C
Day/Night mode
for adjusting the brightness of the display to
day or night conditions
Buzzer ON/OFF
for switching the buzzer ON/OFF
Display brightness
for setting the display brightness
Day mode: 50 %, 75 % or 100 %
Night mode: 5 %, 10 % o 20 %
Language selection/
Autostart function on/o
For setting the display language
Unit selection
for switching the units "bar/°C" to "psi/°F" and
vice versa
Navigating the settings menu
Button Task
Select between the menu items, selection is highlighted
OK Change settings or open submenus
SET Return to vehicle view
Switching between pressure, temperature and target pressure
indicator
TEMPERATURE (°F)
60 60
60 60 60 60
60 60 60 60
PRESSURE (PSI)
10.0 10.0
10.0 10.010.0 10.0
10.0 10.0
10.0 10.0
RCP (PSI)
10.0 10.0
10.0 10.0 10.0 10.0
10.0 10.0 10.0 10.0
Press the button to switch between the pressure indicator, temperature indicator
and the target pressure indicator.

3
Priority: Level Symbol Warning
message Fault
High
Low
High
3*)
FAST PRESS. LOSS
Continuous, fast pressure loss. Tire dam-
age or even tire destruction is possible.
6.2
1*), 2*)
VERY LOW PRES
SURE
The tire pressure falls below the recom-
mended alarm threshold value. Tire dam-
age or even tire destruction is possible.

2*)
CHECK SENSOR
The tire sensor is no longer properly ixed.
Low
8.2
1*)
LOW PRESSURE
The tire pressure falls below the recom-
mended alarm threshold value. The tire
could be damaged in the long term.
115 TEMPERATURE
The measured temperature in the tire
exceeds 115 °C. The tire sensor does not
function at 120 °C.
9.6
4*)
PRESSURE DIFF.
The pressure between two twin tires
exceeds a ixed threshold. The tires could
wear out dierently in the long term.
NO SIGNAL
Due to insuicient signal strength, it is not
possible to display a sensor protocol.
SENSOR DEFECT
Sensor is defective
1*) Pressure value is only an example, threshold values can be stored according to the manufacturer's instructions by a
specialist garage
2*) High warning levels are indicated by lashing symbols changing between positive and negative mode..
3*) The display changes between the symbol shown and the pressure value.
4*) The symbol of the pressure dierence warning message is displayed for the two aected twin tires between which the
pressure dierence was detected.
See the user manual for handling instructions for the above-mentioned errors!
NOTE
►Increase the tire pressure only when the tire temperature corresponds to the
ambient temperature. Otherwise there is a risk that the wrong pressure is
set.
Warning message overview

4
Pressure control indicator operating status on the trailer
Display operational conditions Note
No signal No warning messages for
the trailer pending.
Failure of the pressure control indicator or
the CPC system on the trailer is not displayed
during the journey.
The CPC system for the trailer is not ready for
operation for the rest of this journey.
Lights up for
15 seconds (when
switching on the
CPC system and
optionally 1* when
moving o after a
longer break)
The CPC system and
the pressure control indica-
tor are ready for operation.
If the pressure control indicator does not
produce a signal when switching on the CPC
system (ignition or pressing the main battery
switch), either the CPC system on the trailer is
not ready for operation or the pressure control
indicator is defective.
In this case, it is not possible to monitor the tire
pressure of the trailer.
Flashes slowly2*There is a "low" level warning
on the trailer.
One of the following warnings is present on one
or more of the trailer tires:
LOW PRESSURE, TEMPERATURE, NO SIGNAL or
SENSOR DEFECT
Flashes quickly3*There is a "high" level warn-
ing on the trailer.
One of the following warnings is present on one
or more of the trailer tires:
PRESSURE LOSS, EXTREMELY LOW PRESSURE
or CHECK SENSOR
Flashes very
slowly4*
There is a system error on
the trailer.
At the next opportunity, visit a service work-
shop and have the system error rectiied.
1* not active for all CPC systems 3* (Blink Code EU: 5x per second)
(Blink Code US: every 4 seconds)
2* (Blink Code EU: every 2.5 seconds)
(Blink Code US: permanently lit)
4* (Blink Code EU: not available)
(Blink Code US: every 2 minutes)
1*-4* The behavior depends on the coniguration deined in the HHT hand-held tool..
See the user manual for handling instructions for the above-mentioned errors!
Multiple warnings
If various problems occur simultaneously, a multiple warning screen is displayed.
3 1
10.0
10.0 10.0 9.1 10.0
10.0 10.0 10.0 10.0

10.0 9.1 10.0 10.0
10.0 10.0 10.0
DEMOUNT TIRE

8.2
LOW PRESSURE
8.3
NO SIGNAL
Press the button to call up each individual warning screen successively.
www.contipressurecheck.com A2C84977100 - 17340570000 Rev.3 KD_CPC_0819_A4_EN