Convair SEELEY INTERNATIONAL CTH08 User manual

OWNER’S MANUAL
Convair Tower Heater CTH08
(English) (CTH08)
ECO
1h
14° 18° 22° 26°
2h 4h 8h

TOWER HEATER - CTH08
|
1
SAFETY
General Safety
Please read these instructions before using the
heater and keep for future reference.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction in
using the appliance by a person responsible
for their safety.
Children should be supervised to ensure that
they do not play with the appliance. Do not
poke anything through the ventilating slits.
Always use the heater in an upright position.
Stand it on a rm, solid, horizontal base (not on
thick pile carpets).
WARNING: In order to avoid
overheating, do not cover the
heater.
Leave nothing hanging above or in front of
the heater (e.g. clothes, curtains, bedding,
fabrics). Be sure that the back panel vent
slots on the heater are uncovered otherwise it
will overheat. Clean these openings at regular
intervals to prevent airow reduction (refer
Maintenance section).
The heater surfaces are hot when in use. To
avoid burns, keep bare skin away from the
top ventilation outlets. Leave plenty of room
around the heater.
Do not use this heater outdoors, or on
wet surfaces. Do not use the heater near
ammable areas or substances.
Electrical Safety
Connect the heater to a single 230 Vac, 10A
socket only. Do not plug into double adaptors
or multi-outlet power boards. Do not use an
extension cord to operate this heater.
Make sure that the heater never comes into
contact with water. Never position the heater
under a power outlet.
Never turn the heater on if the power supply
cord is damaged or if the heater’s casing
is obviously damaged. If the power supply
cord is damaged it must be replaced by the
manufacturer, a service agent or similarly
qualied persons in order to avoid a hazard.
Do not pull the heater along by the power cord
or place the cord near the heater’s surfaces.
Always uncoil the power cord completely
before use. Use of extension cords is not
recommended.
Do not use this heater in the immediate
surroundings of a bath, a shower or a
swimming pool. If the heater is to be used in
a bathroom, ensure that switches and other
controls cannot be touched by a person in the
bath or shower.
Do not use this heater with a programmer,
timer, separate remote-control system or
any other device that switches the heater on
automatically, since a re risk exists if the
heater is covered or positioned incorrectly.
Always turn the heater off and unplug from the
power socket when not in use.
Safety Device
To avoid overheating problems the inbuilt
safety device will interrupt electricity in the
event of the heater overheating.
If this should happen:
• Check that the heater is positioned
correctly, not close to any furnishings.
• See that there is no dust or other obstacles
blocking the vent slots.
• Clean the vent slots if necessary.
The heater is also equipped with a ‘tip-over’
switch, which will turn off power to the heater
elements if it should fall over.

OWNER’S MANUAL |2
1. Control panel
2. Display Panel
3. Body sensor
4. Front Grille
5. Handle
6. Remote holder
7. Air inlet grille
8. Power Isolation Switch
9. Base (Locking nut not shown)
10. Mains power cord
11. Remote control
ASSEMBLY
COMPONENTS LIST
REMOTE
When the heater power is on, the remote
control can be used to operate the heater from
up to 4m away.
If there are two or more heaters within this
distance all will be operated by the same
remote control.
Replacing the battery
Release battery slide by pressing on the tab at
the bottom of the remote. Remove the battery
and replace with an equivalent CR2032 type
battery.
Note: Your remote control will be supplied with
a battery.
ECO
1h
14° 18° 22° 26°
2h 4h 8h
1
2
3
4
5
6
7
8
10
ASSEMBLY
Unpack the heater components and check that
you have all of the components.
Turn the heater upside down and remove
the plastic Locking nut. Assemble the Base
onto the heater and lock into position with the
Locking nut.
Note: Ensure the nut is tight to avoid shaking
of the heater.
11
9

TOWER HEATER - CTH08
|
3
OPERATION
Ensure the heater is plugged into a mains
power outlet and is switched on.
Turn the isolation switch on (I), at the back of
the heater, to begin use. The heater will make
a ‘beep’ and the power indicator on the display
panel will become lit.
The control panel or the remote control can
be used to operate the heater, except for ECO
mode, which is exclusively on the control
panel.
OPERATION
DISPLAY
Control Panel
Remote Control
ON/OFF Button HEAT Button
TEMP set Button TIMER Button
SWING Button
BODY sensor
Button
1h
14° 18° 22° 26°
2h 4h 8h
HEAT
Button
TIMER
Button
SWING
Button
ON/OFF
Button
TEMP
Button
BODY
sensor
Button
ECO
Button
1h
14° 18° 22° 26°
2h 4h 8h
ECO
Body
sensor Temperature
setting
Timer
setting
High
Heat
Swing
Low
Heat
Power
Display Panel Indicators
OPERATION CONT.
Turning on/off
Press the ON/OFF button, on the heater or
remote, to turn the heater on. The heater will
start in the last operating mode used.
To turn the heater off press the ON/OFF
button.
Note! The fan will continue to run for a further
ten (10) seconds, after the heater is turned off.
Heat settings
The heat setting can be switched between
low heat (1700W) and high heat (2400W) by
pressing the HEAT button.
Swing function
The heater can be set to oscillate from side to
side to better distribute heat within the room.
Press the SWING button to turn swing mode
on & off. The swing indicator on the display
panel will be lit when swing mode is on.
Temperature control
The heater has an option to control the room
temperature to a set point. The temperature
can be set to 14°C, 18°, 22°C or 26°C.
When the room temperature exceeds the set
temperature the heater will turn off. When the
room temperature drops 2°C below the set
temperature the heater will resume heating.
Set the temperature control by pressing the
TEMP button. The indicators on the display
panel will show the temperature selected.
If no indicators are lit then temperature control
is not selected, and the heater will continuously
operate.

OWNER’S MANUAL |
Make sure that the device is switched off
before cleaning.
Wipe the surface of the heater by using a clean
damp cloth.
Do not use chemical liquids when cleaning
the heater.
Do not submerge the heater in water.
Make sure that the heater has cooled down
completely before storing. Storing in its original
packaging is highly recommended.
CLEANING AND STORING
4
Waste electrical products must not be disposed of with household waste.
This product should be taken to your local recycling centre for safe treatment.
OPERATION CONT.
ECO mode
ECO mode will automatically adjust the heat
setting (low and high) of the heater according
to the room temperature. Refer to table below
for operating logic:
Room Temperature Heat Setting
TR < 18°C High heat
18 °C < TR < 22°C Low Heat
22°C > TR°C Off
Note! Heat and temperature control settings
cannot be adjusted in ECO mode.
Body sensor
In body sensor mode the heater is looking to
detect humans in the room. If a human body is
not detected the heater will turn off after two (2)
minutes. The body sensor indicator will ash
when the heater has switched off. Heating will
immediately resume when a human is sensed.
Note! Body sensor mode does not operate
when oscillation mode is selected.
Body sensor mode can be cancelled anytime
by pressing the body sensor button until the
light on the display panel goes out.
Note! ECO mode will not work when the body
sensor is active.
Timer
A timer can be set to automatically switch the
heater off after a set period of time. To set,
press the TIMER button once to set to the time
to one (1) hour, press twice to set to two (2)
hours, press three times to set to four (4) hours
and press four times to set to eight (8) hours.
The timer indicators on the display panel will
show the selected time.
Cancel the a timer by pressing the TIMER
button until no lights are lit or by turning the
heater off.

TOWER HEATER - CTH08
|
In this warranty:
We or us means Seeley International Pty Ltd. ABN 23 054 687 035, and our contact details are set out at the end
of this warranty;
You means you, the original end-user purchaser of the Goods;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods in Australia; and
Goods means the product, unit, appliance or equipment which was accompanied by this warranty and purchased
in Australia.
Our Goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the Goods repaired or replaced if the Goods fail to be of acceptable quality and the failure
does not amount to a major failure.
In addition to any rights and remedies that You may have under the Australian Consumer Law or any other law,
subject to the terms of this warranty, We provide the following warranty:
1. If, during the rst 24 months from the date of rst retail purchase (Warranty Period), the Goods upon
examination prove defective by reason of improper workmanship or material, We will replace the Goods or any
part thereof without charge. We may substitute with any similar Goods (including a panel heater, or a portable
heating product of a different size or shape), even if it is not on our current price/equipment list. Alternatively,
we may arrange a refund of the purchase price you paid.
2. We are under no obligation to replace the Goods under clause 1 if the Goods have not been used only for
personal, domestic or household purposes and have not been installed/mounted
(if relevant), operated, and maintained in accordance with the instructions in the Owner’s Manual. The addition
of any third party device or the removal or the alteration of any of our components will void this warranty. In
addition, the warranty granted under clause 1 does not apply to:
• Adjustments necessary due to misuse of the appliance,
• Normal user maintenance,
• Setting of controls,
• Transit damage, or
• Damage caused by user misuse, tampering, or failure to observe the care and special provisions in the
instructions.
3. The warranty granted under clause 1 is limited to replacement only. As far as the law permits, We will not be
liable for any consequential loss suffered through, or resulting from, the non operation, or ineffective operation
of the Goods. The warranty granted under clause 1 does not cover damage to the Goods or other loss
resulting from acts of God.
4. No other person, rm or corporation is authorised by us to offer or give on our behalf any other or greater
warranty than that given under this warranty. The benets conferred by this warranty are in favour of You and
any person deriving title to the Goods through or under such person and are intended to be separate from and
additional to all other rights and remedies that they may have in law in respect of the Goods.
5. We are not responsible in any way for any failure and/or inadequate performance of the Goods which arises
from or is connected to the use in the Goods of non-genuine spare parts. We strongly recommend that only
spare parts supplied or approved by us are used in the Goods.
6. In order to claim under the warranty granted under clause 1 You must within the Warranty Period return the
Goods to the Supplier at the place of purchase together with the proof of purchase.
7. Alternatively, you may claim under the warranty granted under clause 1 by within the Warranty Period returning
the Goods to us at the address below together with: (i) a covering letter which states your name and address,
daytime telephone number, and model and serial number of the goods, (ii) the legible and unmodied proof of
purchase, which clearly indicates the name and address of the original retailer, the date and place of purchase,
WARRANTY
5

OWNER’S MANUAL |
and the product name or other product serial number, and (iii) a copy of the completed Warranty Information
below.
8. This warranty does not cover the cost of claiming under the warranty, it is your responsibility to cover all
forwarding and freight costs incurred in returning the Goods to the Supplier at the place of purchase or us.
9. This warranty is only valid and enforceable in Australia.
Our liability under this warranty is limited to the extent permitted by law. That is, to the extent that it is fair
and reasonable, if the Goods are not of a kind ordinarily acquired for personal, domestic or household use or
consumption, your remedies associated with any failure or defect of the Product will be limited to:
(a) the replacement of the Goods or the supply of equivalent goods;
(b) the repair of the Goods;
(c) the payment of the cost of replacing the Goods or of acquiring equivalent goods; or
(d) the payment of the cost of having the Goods repaired and subject to the terms and conditions included in this
warranty.
For technical assistance before returning the product please contact:
1300 650 399
Please retain your receipt as proof of purchase. Every request for warranty must be accompanied by
proof of purchase.
Complete the following for your records:
Serial Number
Product Convair Tower Heater
Model: CTH08
Purchased from
Date purchased
You can also register your warranty with us on our website.
Service Department
Seeley International Pty Ltd
112 O’Sullivan Beach Road
Lonsdale, South Australia 5160
Technical assistance in Australia: 1300 650 399
Website: www.seeleyinternational.com
PRIVACY NOTICE
Seeley International Pty Ltd ABN 23 054 687 035 will use the personal information you provide us with to provide
warranty support for the product you have purchased and to inform you about other products and services. If you
choose not to supply us with the information requested, we may be unable to provide you with warranty support.
We may also disclose your information to third parties, such as related entities; retailers, distributors, service
agents and contractors who are afliated with us; or marketing or market research companies. If you would
prefer not to receive direct marketing communications from us, please follow the instructions to “unsubscribe”
which will be included in the direct marketing communications we send you, or contact our Privacy Ofcer using
the details set out below. While we do not currently transfer personal information to overseas recipients or store
personal information overseas, if we transfer your information to third parties who do so, we will take reasonable
steps to ensure that the overseas recipients do not breach the Australian Privacy Principles. By registering your
warranty, you consent to having your personal information used in this way. Please read our Privacy Policy on our
website www.seeleyinternational.com for further explanation of how we collect, use, hold and disclose personal
information, and how you may access and seek correction of your information. It also sets out how you may
complain about a breach of the Australian Privacy Principles, and how we will deal with your complaint. You may
contact us at: Privacy Ofcer, Seeley International Pty Ltd, 112 O’Sullivan Beach Road, Lonsdale, South Australia
5160.
6
WARRANTY CONT.

seeleyinternational.com
Warranty Service
Australia 1-300-650-399
seeleyinternational.com
It is the policy of Seeley International to introduce continual product improvement.
Accordingly, specications are subject to change without notice.
Please consult with your dealer to conrm the specications of the model selected.
AU 170100173901-A