Converters.TV 922 User manual

HD & IR over single CAT5e/6
Transmitter & Reciever - ID# 922-923
Operation Manual

Introduction
The device that can make your home or office more efficient, this unit of
HDMI with RS-232 over Sing e CAT5e/CAT6 can transmit and receive
uncompressed audio/video, contro through the bui t-in RS-232 and IR
ports over 100M. Hence, if you want to make your home or office more
efficient, get the HDMI & IR over Sing e CAT5e/CAT6 and prepare to be
amazed.
Features
•HDMI 1.4 with 3D, 4k x 2k support, HDCP & DVI Comp iant
•Supports HDCP repeater and CEC function
•Simu taneous y uncompressed data sending over a sing e 100M/328ft
with CAT6 or CAT5e cab e
•Uncompressed video 1080p, 60Hz, 36bits
•Audio support up to 7.1CH & Do by TrueHD, DTS-HD
•3P ay™ convergence: HDMI & Contro (IR & RS232)
•Insta ation Friend y
Note:
This system was tested with CAT6/23AWG cab e, so if using cab es of another
type, resu ts may vary.
Applications
•Househo d entertainment sharing and contro
•Lecture room disp ay and contro
•Showroom disp ay and contro
•Meeting room presentation and contro
•C assroom disp ay and contro
System
Requirements
Input HDMI source equipment such as DVD/B ue-Ray p ayer and output
disp ay with HDMI input jack.

Operation Controls
and Functions
ransmitter
①. RS-232 In: This s ot is to connect with 3.5Ø phone jack RS-232 cab e from
PC/NB equipment for sending RS-232 commands.
②. IR Extender 2: This s ot is to connect with the IR receiver cab e inc uded in
the package for IR signa receiving.
③. IR Blaster 1: This s ot is to connect with the IR b aster cab e inc uded in the
package for IR signa transmitting.
④. HDMI In: This s ot is to connect with HDMI source equipment such as DVD/
B u-ray p ayer.
⑤. DC 5V: This s ot is where you p ug the 5V DC power supp y into the unit and
connect the adaptor to an AC out et.
⑥. Power LED: This green LED wi i uminate when the device is attached with
power supp y.
⑦ Link LED: This ye ow LED wi i uminate when the both CAT5e/6 input and
output signa is connected.
⑧. CAT5e/6 Out: This s ot is to be connected with a sing e CAT5e/6 cab e with
receiver side for data transmitting.
Receiver
①. RS-232 Out: This s ot is to connect with 3.5Ø phone jack RS-232 cab e from
device equipment for receiving RS-232 commands.
②. IR Extender 1: This s ot is to connect with the IR receiver cab e inc uded in
the package for IR signa receiving.
③. IR Blaster 2: This s ot is to connect with the IR b aster cab e inc uded in the

package for IR signa transmitting.
④. HDMI Out: This s ot is to connect with HDMI TV/monitor for disp ay HDMI
input source signa .
⑤. DC 5V: This s ot is where you p ug the 5V DC power supp y into the unit
and connect the adaptor to an AC out et.
⑥. Power LED: This green LED wi i uminate when the device is attached with
power supp y.
⑦ Link LED: This ye ow LED wi i uminate when the both CAT5e/6 input and
output signa is connected.
⑧. CAT5e/6 In: This s ot is to be connected with a sing e CAT5e/6 cab e from
transmitter side for data transmitting.
D-Sub 9 Pin
Definitions
PIN Define X / RX
1 N/C
2 TxD / RxD
3 TxD / RxD
N/C
5 GND
6 N/C
7 N/C
8 N/C
9 N/C
Specifications
Transmitter
Input 1 x HDMI, 1 x IR Extender, 1 x RS-232
Output 1 x CAT5e/6, 1 x IR B aster
Receiver
Input 1 x CAT5e/6, 1 x IR Extender
Output 1 x HDMI, 1 x RS-232, 1 x IR B aster
ESD Protection Human Body Mode :
± 8kV (air-gap discharge)
± 4kV (contact discharge)
IR Frequency 30~50kHz
Dimensions (mm) 71(W) x 79(D) x 23(H)
Weight (g) 240/Tx, 245/Rx
Chassis Materia A uminum
Si kscreen Co or B ack
Power Consumption TX: 3W ; RX: 6W
Operating Temperature 0°C ~ 40°C/ 32° ~104°
Storage Temperature -20°C ~ 60°C/ -4° ~140°
Re ative Humidity 20~90% RH (non-condensing)

Connection