Converters.TV 15532 User manual

HDBaseT HDMI over CAT5e/6/7 Wallplate
Receiver w/ 24vPoC & AN Serving - # 15532
Operation Manual

Introduction
The HDMI over Single CAT5e/6/7 Wall-plate Receiver is designed to
receive ncompressed video, a dio and IR control data from a compatible
transmitter over a single r n of CAT5e/6/7 cable at a distance of p to 100
meters. It has the added benefit of control thro gh the b ilt-in RS-232 and
IR ports and a bi-directional LAN serving connection. Additionally, it can be
powered by a compatible transmitter nit via the Power over Cable (PoC)
f nctionality allowing for greater flexibility in installations.
Applications
• Extend an HDMI signal to a remote location
• Ho sehold entertainment sharing and control
• Showroom display and control
• Classroom display and control
Features
• HDMI with 3D, 4K2K support, HDC and DVI compliant
• Sim ltaneo s tranmisson of ncompressed data over a single 100m
CAT5e/6/7 cable (70m for 4K2K signals)
• Uncompressed video s pport p to 1080p@60 Hz/36-bit
• High definition a dio s pport p to LPCM 7.1CH, Dolby Tr eHD, Dolby
Digital Pl s and DTS-HD Master A dio
• HDBaseT™ 5PlayT™ convergence: ncompressed high definition Video
and A dio, LAN serving, Power over Cable (PoC) and RS-232/IR control
• S pports HDCP repeater and CEC bypass f nctions
• Easy to install wall plate design
Note:
1. This system was tested with CAT6/23AWG and CAT5e/24AWG cables,
res lts may vary with cables of a different specification.
2. The PoC f nction req ires a compatible Transmitter nit.
Transmitters from other brands may not be compatible.
3. For playback of 4K2K HDMI so rce signals, a 4K2K capable display
and High Speed HDMI cables are req ired.
System
Requirements
• HDMI eq ipped so rce device (connected with HDMI cables) or DVI
eq ipped so rce (connected with DVI to HDMI cables)
• HDMI eq ipped display (TV or monitor) or AN HDMI eq ipped AV
receiver, connected with HDMI cables
• Ind stry standard CAT5e/6/7 cables
• Compatible PoC HDBaseT™ Receivers

Operation
Controls and Front Panel
Functions
1. IR 1 EXTENDER:
Connect an IR Extender cable for IR signal reception. Signals received will
be transmitted from any IR blaster connected to the transmitter nit.
Ens re that the remote being sed is within the direct line-of-sight of the IR
Extender
2. IR 2 BLASTER:
Connect an IR Blaster cable for IR signal transmission.
IR signals received by an IR extender connected to the transmitter nit will
be transmitted by this blaster. Place the IR Blaster in direct line-of-sight of
the eq ipment to be controlled
3. RS-232 OUT:
Connect to the device that is to be controlled (via D-s b 9-pin female
cable) by RS-232 commands.
4. LAN:
Connect to an active network for LAN serving. When the transmitter or any
compatible LAN eq ipped receivers are connected to a network, this
allows the network access (incl ding internet access if available) to be
shared between the receiver and all connected receivers. Connect any
Ethernet eq ipped device e.g. a Smart TV or games console to the LAN
port of a receiver for that device to share the network/internet access.
5. HDMI OUT:
Connect to a HDMI eq ipped TV/monitor for display of the HDMI inp t
so rce signal.
6. POWER LED:
This LED will ill minate when the device is connected to a power s pply or
powered by another nit via PoC.
7. LINK LED:
This LED will ill minate when both the so rce connected to the transmitter
and the display connected to the receiver are connected.
.

Rear Panel
1. CAT5e/ /7 IN:
Connect to the transmitter nit with a single CAT5e/6/7 cable for
transmission of all data signals.
IR Cable
Pin Assignment

D-Sub 9-Pin
Assignment
Pin Assignment
1 N/C
2 Tx/Rx
3 Rx/Tx
4 N/C
5 GND
6 N/C
7 N/C
8 N/C
9 N/C
CAT5e/6/7 Cable
Specification
Cable
Type
Range Pixel Clock
Rate
Video Data
Rate
Supported Video
CAT5e/6/
7
100m≤225 MHz ≤5.3 Gbps
(HD Video)
Up to 1080p, 60Hz,
36-bit 3D (Data rates
lower than 5.3Gbps or
below 225 MHz TMDS
clock)
70m >225 MHz >5.3 Gbps
(Ultra HD
Video)
4K2K, 30Hz video
formats

Specifications
Video Bandwidth 300 MHz/10.2 Gbps
Input Ports 1×CAT5e/6/7,1×LAN, 1×IR Extender
Output Ports 1×HDMI,1×RS-232, 1×IR Blaster
Power Supply 24 V/6.25 A DC (US/EU standards, CE/FCC/
UL certified)
ESD Protection H man Body model:
± 8kV (air-gap discharge)
± 4kV (contact discharge)
IR Frequency 20~60 kHz (under optimal conditions)
Dimensions 145.7 mm (W)×85.7 mm (D)×39.5 mm (H)
Weight 160g
Chassis Material Metal
Silkscreen Color Black
Operating Temperature 0 ºC~40 ºC/32 ºF~104 ºF
Storage temperature −20 ºC~60 ºC/−4 ºF~140 ºF
Relative Humidity 20~90% RH (no condensation)
Power Consumption 12 W (PoC), 9 W (Main)

Connection Diagram