Cooper Lighting DE621 User manual

311
TRACK LIGHTING Single Circuit
COOPER LIGHTING
HALO®
L904 L Connector
To connect two track sections at a right angle.
Field adjustable for either right hand or left hand
application. May be used as feed point.
Finish: White (P), Black (MB)
L906 X Connector
To connect four track sections into a cross
configuration. May be used as feed point.
Finish: White (P), Black (MB)
L908 Mini Joiner
A low profile connector to cleanly and crisply
join two straight track sections end-to-end.
(Note: The L908 is not a feed point).
Finish: White (P), Black (MB)
L950 Cord and Plug Connector
12’ three-wire cord with grounded plug.
Maximum capacity 10 AMP
Finish: White (P), Black (MB)
L979 Conduit Continuation Kit
Consisting of one left feed and one right feed.
To continue a run around obstructions. Designed
to accept 1/2” trade size conduit fitting (not
included).
Finish: White (P), Black (MB)
L983 T-Bar Attachment Clip
Allows track to be attached to inverted tee ceiling.
Order as follows: 2 kits for 2’ Trac; 2 kits for 4’
Trac; 3 kits for 8’ Trac and 4 kits for 12’ Trac.
L986 Mini-T Bar Clip
For mounting Trac on suspended ceilings with
mini-grid (9/16” wide) system.
L994 45° Pendant Adapter
For installing pendant mounted Power-Trac on
sloped ceiling. For use with L992 and L993.
Finish: White (P), Black (MB)
L905 T Connector
To connect three track sections into a T
configuration. Field adjustable for either right
hand or left hand application. May be used as
feed point.
Finish: White (P), Black (MB)
L907 Outlet Box for use with
T-Bar ceiling
L901, L903, L904, L905 or L906 connector also
required. 4”x 4” x 1 1/8”.
Finish: White (P), Black (MB)
L909 Floating Canopy and
Connector
Track can be connected to existing outlet
box located anywhere along the track. Comes
with canopy cover, connector, dead-end and
mounting hardware. 4 1/8” x 4 1/4” x 1 3/8”.
Finish: White (P), Black (MB)
L951 Wire Way Cover for Pendant
Assembly Kit
For track to be wired through stem (order one
for each feed point used). Shown with end
feed and pendant stem kit–order separately
Finish: White (P), Black (MB)
L980 Live End Conduit Adapter
Designed to accept standard 1/2” trade size
conduit fitting (not supplied). Use when
feeding to track through surface conduit
system.
Finish: White (P), Black (MB)
L992 Pendant Kit Assembly
Order 2 kits for 2’ Trac; 2 kits for 4’ Trac; 3 kits
for 8’ Trac; and 4 kits for 12’ Trac. Includes one
18” threaded steel stem, canopy and mounting
hardware.
L48 48” Steel Stem
For additional length with L992. Can be field cut.
Finish: White (P), Black (MB)
DE600 Dead End
Replacement Dead Ends for Single Circuit Track
(6 included)
Finish: White (P), Black (MB)

313
TRACK LIGHTING Two Circuit
COOPER LIGHTING
HALO®
L994 45° Pendant Adapter
For installing pendant mounted Power-Trac on
sloped ceiling. For use with L992 and L993.
Finish: White (P), Black (MB)
L983 T-Bar Attachment Clip
Allows track to be attached to inverted tee
ceiling. Order as follows: 2 kits for 2’ Trac; 2
kits for 4’ Trac; 3 kits for 8’ Trac; and 4 kits for
12’ Trac.
L986 T-Bar Attachment Clip
For mounting track on suspended ceilings with
mini-grid (9/16" wide) system.
L949 Mini Joiner
To join two straight track sections end-to-end.
Not a feed point.
Finish: White (P), Black (MB)
L946 X Connector
To connect four track section into a cross
configuration. May be used for feed point.
Finish: White (P), Black (MB)
L945R Right T Connector
“T” connector for joining three trac sections
with right hand polarity. May be used as feed
point.
Finish: White (P), Black (MB)
L942 Flex Joiner
To connect two track sections at any angle up
to 90,° in either plane or wall to ceiling or
pitched ceiling applications.
Finish: White (P), Black (MB)
L992 Pendant Kit Assembly
To suspend track from ceiling. Order as
follows: 2 kits for 2’ Trac; 2 kits for 4’ Trac; 3
kits for 8’ Trac; and 4 kits for 12’ Trac. Includes
one 18” threaded steel stem, canopy and
mounting hardware.
Finish: White (P), Black (MB)
L48 48” Steel Stem
For additional length of stem for L992. Can be
field cut and threaded.
DE641 Dead End
Replacement Dead Ends for Two Circuit Track
(6 included)
Finish: White (P), Black (MB)
L989 Conduit Continuation Kit
Includes one left and one right feed. To
continue
a run around obstructions with 1/2” trade size
surface conduit.
Finish: White (P), Black (MB)
L951 Wire Way Cover for
Pendant Assembly Kit
For track to be wired through stem (one for
each live end used). Shown with end feed and
pendant stem kit–order separately
Finish: White (P), Black (MB)
L947 Conduit Connector
A live end connector for use with surface
conduit. Designed to accept standard 1/2”
conduit fitting (not included). May be used for
feed point.
Finish: White (P), Black (MB)
L945L Left T Connector
“T” connector for joining three trac sections
with left hand polarity. May be used as feed
point.
Finish: White (P), Black (MB)
L943 Straight/L Connector
To connect two track sections end-to-end or at
a 90° angle. May be used as feed point.
Finish: White (P), Black (MB)
L929 Floating Canopy and
Connector
Can be connected anywhere along length of
Trac. Comes with canopy cover, connector,
dead-end and mounting hardware.
Finish: White (P), Black (MB)

317
TRACK LIGHTING Four Circuit
COOPER LIGHTING
HALO®
L900 Outlet Box Cover
Can be used at any electrical feed connection
point (Live, Straight, L, T or X). Size: 5” sq.
Screws included.
Finishes: White (P), Black (MB)
L923 Straight Connector
To connect two track sections end-to-end. May
be used as feed point.
Finishes: White (P), Black (MB)
L925 T Connector
To connect three track sections into a T
Configuration. May be used as feed point.
Finishes: White (P), Black (MB)
L954 Pendant Kit
To suspend track from the ceiling. Order as
follows: 2 kits for 2’ Trac; 2 kits for 4’ Trac; 3 kits
for 8’ Trac; 4 kits for 12’ Trac. 18” threaded steel
stem, one canopy and mounting hardware.
Finishes: White (P), Black (MB)
L982 Conduit Connector
A Live End Connector for use with surface
conduit. Designed to accept standard 3/4” trade
size conduit fitting (not supplied).
Finishes: White (P), Black (MB)
L983 T-Bar Attachment Clip
Allows track to be attached to inverted tee
ceiling. Order as follows: 2 kits for 2’ Trac; 2 kits
for 4’ Trac; 3 kits for 8’ Trac and 4 kits for 12’ Trac.
L921 Live End Connector
To start a run.
Finishes: White (P), Black (MB)
L924 L Connector
Connects two track sections at a right angle.
May be used as feed point.
Finishes: White (P), Black (MB)
L926 X Connector
To connect four track sections into a cross
configuration. May be used as feed point.
Finishes: White (P), Black (MB)
L963 Single-Circuit to Four-Circuit
Convertor with Switch
Allows any Halo Power-Trac lampholder
(except solid state low voltage and L3218, L3232,
L3239, L5120, L5130, L5138) to be used with Four
Circuit Trac. One converter is required for each
Power-Trac lampholder used. This adapter is
designed to fit into the trac in either of two
directions. Facing in one direction, it makes
contact with circuits 1 and 2, with a 3-position
switch (on-off-on) used to select the desired
circuit. To connect the fixture with circuits 3 or 4,
the adapter is removed from the trac, turned
180°, and is then re-inserted into the trac.
L963 is rated at 500 watts maximum.
Finishes: White (P), Black (MB)
DE621 Dead End
Replacement Dead Ends for Four-Circuit track (6
included)
Finishes: White (P), Black (MB)

318
TRACK LIGHTING Architectural Track
COOPER LIGHTING
HALO®
LA631, LA632, LA633
Halo Architectural Track (includes dead end and
mounting hardware). Connectors must be
ordered separately.
•LA631–4’ Track. Actual length 42-7/32”
(1072mm).
Finishes: White (P), Black (MB), Silver (SL)
•LA632–8’ Track. Actual length 88-7/32”
(2240mm).
Finishes: White (P), Black (MB), Silver (SL)
•LA633–12’ Track.
Actual length 136-7/8” (3460mm).
Finishes: White (P), Black (MB), Silver (SL)
Halo 2 circuit Architectural 120V and 277V
Track system provides two separate 40
AMP circuits and two neutrals. Each
circuit can be independently switched.
Fully polarized and grounded throughout.
Top portion of track is designed as a
raceway for carrying up to 2 #8AWG
conductors. Raceway can be used to feed
additional sections of track from the
original feed point, minimizing
installation time and cost.
Halo 2 Circuit Architectural Track accepts
Halo Architectural lampholders. When
using Halo power-Trac Lampholders, an
LA1L converter is required (see
Lampholder/Track Compatibility listings
with lampholders). Halo Architectural
Track is suitable for a wide range of
commercial, merchandising and retail
applications.
Structural:
Extruded aluminum .080" [2.03mm]
nominal wall thickness. Raceway Trac is
only 1 7/16” (37mm) deep by 1 13/16”
(46mm) wide.
Line Conductor:
Solid copper alloy bus bars [cross section
equivalent to #8 AWG wire].
Insulating Liner:
Extruded polyvinyl insulator.
Ground Conductor:
Maintains an independent positive
ground path between lampholder, Track
channel and building’s ground system.
Neutral Conductor: 2 neutrals [each
cross section equivalent of #8 AWG wire].
Raceway Capacity for Additional Circuits:
Carries up to two #8 AWG conductors.
Electrical capacity is 40 AMPS.
Listings:
UL/cUL listed for use with Halo 120V and
277V Architectural lampholders.
(See Below)
P=Satin White
MB=Matte Black
SL=Silver
LA631=4'
LA632=8'
LA633=12'
Accessories (Order Separately)
Finishes
Blank=120V
277=277V
VoltageTrack
LA631
L= 4'’
Actual length
42 7/32" [1072mm]
W=1 13/16" [46mm]
H=1 7/16" [34mm]
Finish Codes:
P=White
MB=Black
SL=Silver
Voltage:
Blank=120V
277=277V
LA632
L=8'’
Actual length
88 7/32" [2240mm]
W=1 13/16" [46mm]
H=1 7/16" [34mm]
Finish Codes:
P=White
MB=Black
SL=Silver
Voltage:
Blank=120V
277=277V
LA633
L=12’
Actual length
136 7/32" [3460mm]
W=1 13/16" [46mm]
H=1 7/16" [34mm]
Finish Codes:
P=White
MB=Black
SL=Silver
Voltage:
Blank=120V
277=277V
Connectors
LA670 = Live End Conduit
Connector
LA671 = Live End Connector
LA672 = Flexible Connector
LA673 = Straight Connector
LA674 = “L” Connector
LA675 = “T” Connector
LA676 = “X” Connector
LA678 = Mini Joiner
Finish Codes:
P=White
MB=Black
SL=Silver
Voltage:
Blank=120V
277=277V
Accessories
L900 = Outlet Box Cover
L983 = T-Bar Attachment Clip
L986 = MiniT-Bar Attachment Clip
LA995 = 18” Pendant Kit
LA48 = 48” Steel Stem
LA996 = Wireway Cover for
Pendant Assembly Kit
LA959 = Wireway Cover (gray
only)
DE661 = Dead End
Finish Codes:
P=White
MB=Black
SL=Silver
1-13/16”
[46mm]
1-7/16”
[34mm]
HALO 2-CIRCUIT, 2 NEUTRAL ARCHITECTURAL TRACK
LA1L 120V Halo Architectural Converter
Allows use of 120V Halo Power-Trac or Lazer Track lampholders on Halo Architectural Track. allows any Halo Power-
trac lampholder (excludes low voltage power supplies except L2005) (excludes L3218, L3232, L5130, , L5138) to be
used with Halo Architectural Track. One converter is required for each Power-trac lampholder used.
Finishes: SL=Silver; P=White; MB=Matte Black