Cooper Lighting Combolight Trimless V90229-1N User manual

JBOX
JBOX COVER
SCREW
DRYWALL
HOUSING
TRIMLESS
INSERT
MUDDING
COMPOUND
DRYWALL SCREW
A
MOUNTING
CHANNEL
BUTTERFLY
MOUNTING
BRACKET
HEX
SCREW
APERTURE
COLLAR
TRIMLESS INSERT
HOUSING
Figure 1
OUTER ALIGNMENT HOLES
OUTER ALIGNMENT HOLES
FIXTURE MOUNTING:
1. First remove TRIMLESS INSERT from Housing by pulling straight out.
See Fig 1. Fixture must be mounted using either BUTTERFLY MOUNTING
BRACKETS or HANGER BARS (Contact RSA Dealer for HANGER BARS).
Figure 4
ELECTRICAL:
7. Remove the JBOX COVER from the JBOX by removing the four SCREWS.
Connect supply lead wires to junction box lead wires in accordance with
your local electrical code(s) or N.E.C. Replace JBOX COVER onto JBOX,
securing with SCREWS. See Fig 3.
Figure 3
CEILING MATERIAL INSTALLATION:
8. A clean, square hole in the CEILING MATERIAL must be cut. Install the
ceiling material below housing as seen in Fig 4.
9. Replace the TRIMLESS INSERT into the HOUSING by pushing until flush
with the CEILING MATERIAL as seen in Fig 4. Using the OUTER
ALIGNMENT HOLES on the TRIMLESS INSERT, screw the TRIMLESS
INSERT into the HOUSING using DRYWALL SCREWS into the Outer
Holes on the TRIMLESS INSERT.
10. Smooth out MUDDING COMPOUND / TAPE from around aperture to
surrounding areas of DRYWALL as seen in Fig 4.
INSTALLATION NOTE:
DO NOT install insulation within 3in of any part of the Luminaire.
Blinking light of this thermally protected Luminaire may indicate overheating.
BUTTERFLY MOUNTING:
2. Fixture comes equipped with universal BUTTERFLY MOUNTING
BRACKETS that can take common 1" or 1-1/2" black iron or galvanized
MOUNTING CHANNELS (supplied by others). See Fig 2.
3. Position fixture so the MOUNTING CHANNELS lie on top of the ceiling
runners.
4. Fasten MOUNTING CHANNELS securely to ceiling runners.
5. Secure MOUNTING CHANNELS to universal BUTTERFLY MOUNTING
BRACKETS with wire tie downs.
6. The BUTTERFLY MOUNTING BRACKETS are height-adjustable and
should be set so that the APERTURE COLLAR will be flush with the
finished ceiling plane.
Figure 2
INSTALLATION INSTRUCTIONS
V90229-1N
Avoid Fire or Electric Shock
COMBOLIGHT
TRIMLESS
Page 1 of 3
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local regulations.
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
R





COVER
RING
BACK RING
COIL SPRING
LAMP
(MR16 shown, COIL
SPRING behind)
BACK RING
SOCKET ASSY
PIVOT JOINT
(FOR GIMBAL
TIGHTENING)
OPTICAL
ACCESSORY
ACCESSORY
RETAINER
RING
COVER
RING
SNOOT
Flush Position Regressed Position
CEILING
LINE
11. Lamp installation:
To install LAMP, remove the COVER RING by pushing straight back on
the COVER RING and then turning it counter-clockwise to release.
See Fig. 5.
12. Once removed, insert the properly-specified LAMP into the
BACK RING, ensure that the LAMP is the correct LAMP for the SOCKET
or damage to the fixture or lamp may occur. The LAMP will seat into the
COIL SPRING when installed properly. While holding the LAMP in place,
grab the SOCKET ASSY and plug or screw the LAMP firmly into it.
See Fig. 6.
Figure 7
Figure 6
(Cover Ring Removed)
Figure 8
Figure 5
13. Optical Accessory: (skip to Step 21 if not using optical accessories)
To install OPTICAL ACCESSORY pieces, remove the ACCESSORY
RETAINER RING by unthreading until it is completely removed from the
COVER RING.
14. Install desired OPTICAL ACCESSORY pieces into the COVER RING and
re-thread the ACCESSORY RETAINER RING firmly. See Fig. 7.
*The COVER RING can accommodate three (3) accessories without the
ACCESSORY RETAINER RING or two (2) pieces with it.
*The ACCESSORY RETAINER RING may be used to lock the accessory.
For example, a linear spread lens or cross baffle can be locked in-place
into a desired orientation.
*Please note that not all accessories are compatible with each other and
with all lamps.
15. Regressed Lamp Ring/Snoot: (skip to Step 19 if not regressing the lamp)
The lamp ring may be installed in a regressed position only if a
SNOOT accessory is being used. See Fig. 8. If necessary, please see step
13 for instructions on SNOOT installation. To accomplish the regressed
lamp ring position set the COVER RING aside. Remove the lamp ring assy
by loosening the two (2) SET SCREWs in the GIMBAL BLOCKs.
16. Once loosened the lamp ring assy can be removed by grasping the
GIMBAL RING and turning
clockwise until it releases from the GIMBAL
BLOCKs.
INSTALLATION INSTRUCTIONS
V90229-2
Avoid Fire or Electric Shock
COMBOLIGHT
LAMPHOLDER
Page 2 of 3
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local regulations.
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
R





GIMBAL BRACKET
(Standard Position)
SLOT
SET SCREW
SNOOT
GIMBAL RING
GIMBAL
BLOCK
17. Once removed, flip the two (2) GIMBAL BRACKETs around (180°) and
tighten the joint if necessary. See Fig. 9.
If necessary, please see Step 21 for gimbal tightening instructions.
18. Reinsert the lamp ring assembly by turning it counter-clockwise into the
SLOTs on the GIMBAL BLOCKs. Re-tighten the two (2) SET SCREWs
in the GIMBAL BLOCKs. The lamp ring assy should now be oriented in
the "up position". See Fig. 10.
BAYONET
SLOTS
COVER
RING
PIN
BACK RING
COVER RING
(AS INSTALLED)
GIMBAL BRACKET
(Rotated 180° to
"Down" Position)
19. To replace the COVER RING:
Push the COVER RING onto the BACK RING by lining up the
BAYONET SLOTS (see Fig. 11) with the two (2) PINs in the BACK RING.
Figure 10
Figure 11
Figure 12
Figure 9
20. Once lined up, push straight back until the COVER RING stops, then
while keeping the COVER RING pushed back, turn clockwise until it
pushes forward again slightly. See Fig. 12.
21. Gimbal tightening instructions:
The lamp ring is intended to give positive tension at the PIVOT JOINTS
so the lamp ring can be aimed by hand and held in place by tension.
*If a stronger, more secure lock is required then the PIVOT JOINTS (hex
screws) may be tightened
clockwise with a hex wrench tool. See Fig. 6.
*Please note that in some conditions the COVER RING will need to be
removed to gain access to the inner PIVOT JOINTS.
INSTALLATION INSTRUCTIONS
V90229-3
Avoid Fire or Electric Shock
COMBOLIGHT
LAMPHOLDER
Page 3 of 3
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local regulations.
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
R



