COP Security 15-CD66WIB User manual

Installation and Operation Manual
for
High Speed Dome Camera
VER: V1.0
15-CD66WIB 15-CD66WB
Please read the operation manual carefully
before installing and using this unit

High Speed Dome Camera Introduction Manual 1
CAUTl0N
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION：To reduce the risk of electrical shock, do not open covers.
No user serviceable parts inside.
Refer servicing to qualified service personal.
This lightning flash with arrowhead symbol is intended to alert the user to the
presence of un-insulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
This exclamation point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING：To prevent the risk of fire or electric shock hazard do not expose
this camera to rain or moisture.

High Speed Dome Camera Introduction Manual 2
▌▌Important Safeguard
1. Read Instructions
Read all of the safety and operating instructions before using the product.
2. Retain Instructions
Save these instructions for future reference.
3. Attachments／Accessories
Do not use attachments or accessories unless recommended by the appliance manufacturer as they
may cause hazards, damage product and void warranty.
4. Water and Moisture
Do not use this product near water or moisture.
5. Installation
Do not place or mount this product in or on an unstable or improperly supported location. Improperly
installed product may fall, causing serious injury to a child or adult, and damage to the product. Use
only with a mounting device recommended by the manufacturer, or sold with the product. To insure
proper mounting, follow the manufacturer’s instructions and use only mounting accessories
recommended by manufacturer.
6. Power source
This product should be operated only from the type of power source indicated on the marking label.
▌▌Precautions
Operating
zBefore using, make sure power supply and others are properly connected.
zWhile operating, if any abnormal condition or malfunction is observed, stop using the camera
immediately and then contact your local dealer.
Handling
zDo not disassemble or tamper with parts inside the camera.
zDo not drop or subject the camera to shock and vibration as this can damage camera.
zCare must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your
quality of camera.
Installation and Storage
zDo not install the camera in areas of extreme temperature, which exceed the allowable range.
zAvoid installing in humid or dusty places.
zAvoid installing in places where radiation is present.
zAvoid installing in places where there are strong magnetic fields and electric signals.
zAvoid installing in places where the camera would be subject to strong vibrations.
zNever expose the camera to rain and water.

High Speed Dome Camera Introduction Manual 3
1. Introduction Features
Product and Accessories
4
8
2. Installation Guide
Preparations
Installation Method
Installation Dimensions
9
10
10
3. Dome Setting
DIP Switch Setup
Cabling
Check points before operation
Start OSD Menu
Reserved Preset
OSD Display of Main Screen
14
15
17
18
18
19
4. How to use OSD Menu Main Menu
System Information
Display Setup
IR Setup
Dome Setup
Camera Setup
Preset Setup
Swing Setup
Pattern Setup
Group Setup
Auto Scan Setup
Zones Setup
Timing Action Setup
Alarm Input Setup
System Initialize
20
21
22
23
24
29
31
32
33
34
35
36
37
38
39
5. Specifications Specifications
Optional Bracket
40
42

High Speed Dome Camera Introduction Manual 4
█
█▐ ▐ F Fe ea at tu ur re es s ▌ ▌█ █
▌▌Camera Specifications
zCCD Sensor: 1 / 4 " Interline Transfer CCD
zCamera Support: CZ36SCM(COP)
Zoom Magnification: x 36 Optical Zoom, x 32 Digital Zoom
zCamera Support: FCB-EX1020(SONY)
Zoom Magnification: x 36 Optical Zoom, x 12 Digital Zoom
zCamera Support: SCM-2270/SCM-2273(SAMSUNG)
Zoom Magnification: x 27 Optical Zoom, x 16 Digital Zoom
zCamera Support: SCM-2370/SCM-2373(SAMSUNG)
Zoom Magnification: x 37 Optical Zoom, x 16 Digital Zoom
zDay & Night Function
zVarious Focus Mode: Auto-Focus / Manual Focus / Semi-Auto Focus.
zIndependent and Simultaneous Camera Characteristic Setup in Preset operation
▌▌Main Features
zStep less speed changes, auto zoom/speed matching
zPan 0.01~360o/S, Tilt 0.01o~120o/S
zTiming actions for 7 days of programmable schedule
zBuilt-in Semi-conductor heater & digital temperature sensor
zPan Tilt accuracy +/- 0.01o, 255preset positions
zMulti-Protocol through RS485 or coaxial cable.
zMax- 8 set of Group action can be stored. This enables to move camera repetitively with
combination of Preset. A Group is composed of max. 16 entities of Preset.
zMax .4 of Patterns can be recorded and played back. This enables to move camera to follow any
trajectory operated by joystick as closely as possible.
zMax. 8 set of Swing action can be stored. This enables to move camera repetitively between two
preset positions with designated speed.
zMax. 1 set of auto scan can be stored. This is to keep the ball machine according to the elevation
angle of executive level 360°continuous rotation and speed can be adjusted.
z8 Privacy Zones with defined English camera title
zAuto Compatible PELCO_P, PELCO_D compatible
zGuard Location: the dome will rotate back to preset position after a period of vacant time
zAlarm triggering: the alarm can trigger preset, auto scan, group and pattern tours functions
zSoft Address Function: the use can set up the dome address without uninstall the dome
zSpecially defrost function to get clear image when the camera is working on the low temperature
environment.

High Speed Dome Camera Introduction Manual 5
▌▌Integrated Super Speed PTZ Rotator..
zDelicate stepping motor, stable, sensitive and accurate
z360° Pan and -10°~90° Tilt range (auto-flip) without blind area
zStepless speed change, auto zoom/speed matching
zNear / far IR Light auto matches camera zoom in/out
▌▌All-weather Outdoor Design
zHigh die-cast alloy aluminum construction
zHigh Precision Mould with high heat conductivity
zFully enclosed isolation design for heat sink
zNanometer Dustproof, waterproof and fog-proof lens
zIP66 Waterproof
z3000V lightning and surge current protection
▌▌Function Instructions
zFocus / PTZ Speed Auto Match
The pan/tilt rotation speed could be automatically adjusted according to the focus in/out, which
makes it much more practical for manual target tracking.
zPower Up Action
This function enables to resume the last action executed before power down. Most of
actions such as Preset, Pattern, Swing ,Auto scan and Group are available for this function but jog
actions are not available to resume.
zAuto Flip
When the camera tilts downward and goes just beyond the vertical position, the camera will rotate
180 degrees.
zPreset Position Set up and Call Up
In the Preset function the dome stores the current pan/tilt angle, zoom and other position parameters
in its memory. When necessary the dome recalls these parameters and adjusts the camera to a
particular position. The user can store, recall and clear the presets easily and promptly by using the
keyboard controller. The dome can store up to 255 presets.
zSwing
Users can set up the left and right boundaries by control keyboard. Then speed
dome can scan between this boundary. It supports up to 8 groups of scanning paths.

High Speed Dome Camera Introduction Manual 6
zGroup
The preset position can be programmed to be recalled in a set of sequences. This sequence can be
set to let the camera scan from one position to the next in a cycle at a set speed. This feature is
called the “auto cruise”. The cruise sequence and dwell time of each preset can be set. It supports
up to 8 cruising tracks, each cruising track with 16 presets.
zPattern Tour
Dome can memorize 160s running path or 500 programmable instructions. When start pattern tour,
speed dome will move automatically according recorded action path. It supports 4 groups of pattern
tours.
zGuard Location
The dome will automatically return to preset position if there is no operation in a period of vacant
time.
zDefault Action
When you start up the dome camera or do not send commands over a long time, the dome camera
will return to its default functions which include the home place, auto pan, auto cruise and pattern.
zDome Address Setup
The dome supports up to 255 addresses and the dome will only response to the instructions given to
its own address. Please check the ball machine code dialing switch address setting.
zManual Object Tracking
The use can move the joystick up, down, left or right to track the appearing object in the screen and
use the joystick to zoom in and out with auto focus.
zPrivacy Mask Protection
Set black mask areas to protect the privacy zones. The black privacy locations can be set, and
support up to 8 mask zones.
zTiming Running Function
Users can set speed dome operation task at total 6timing areas during 7 days.
zCoordinates and Directions Display
User can define the dome’s direction of due north, which will help to show up the exact moving
directions on screen. And zone title is supported to display when the dome moves to the specified
zone.

High Speed Dome Camera Introduction Manual 7
zPTZ and Lens Control
1Zoom Control
Users can control zoom by keyboard to get near or far images.
dFocus Control
The default setting is auto focus. The camera will auto focus based on the center of the video
display to get the clear image. In some special occasions, the user could do the manual focus
to get the desired image effect.
eAuto Iris Control
Auto Iris is aiming to detect the environmental lights condition and adjust the iris to get the
stabilized brightness of the image.
4Auto Back Light Compensation
In the highly bright background, auto back light compensation is aiming to compensate the
brightness of the dark object and adjust the background brightness to get a clear image.
5Auto/Manual White Balance
Auto/Manual WB adjust depending on the environment light changes.
6Day and Night Switch (Only for Day/Nigh Camera)
Speed dome camera can auto switch according to the environmental illumination changes.
zI/O Functions
To reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo
coupler.
Using the dry contact for alarm input and output.
If an external sensor is activated, camera can be set to move to the corresponding Preset position.
zReserved Presets for Special Purpose
Most camera characteristics can be set up easily and directly with reserved preset, not entering
into OSD menu. For more information, refer to “Reserved Preset” in this manual.

High Speed Dome Camera Introduction Manual 8
▌▌Product & Accessories
15-CD66WIB 15-CD66WB
zAccessories:
User’sManual Anti-dropRope&Screw
Caution：AC24V/3A power for 15-CD66WIB
AC24V/2A power for 15-CD66WB

High Speed Dome Camera Introduction Manual 9
█
█▐ ▐ I In ns st ta al ll la at ti io on n G Gu ui id de e ▌ ▌█ █
▌▌Preparations
zBasic Requirements
All the electric work must be finished under the latest electric & fire prevention law and rules (and
any related law and rules). Please check according to the packing list if every accessory is included.
And also make sure the installation is operated as required. Please contact us for any help during
the installation.
zInstallation Space and Density Checkup
Please make sure the space is big enough to install our dome. And also ensure the density of the
ceilings or walls to hold total weight of the dome and its accessories.
zCables Preparation
Please choose the proper cable according to the transmission distance. The min requirement of
coaxial BNC cable is listed as follows for reference:
ModelsMaxDistance（Feet\Meter）
RG59/U750ft(229m)
RG61/U1,000ft(305m)
RG11/U1,500ft(457m)
zSetup Dip Switch for Dome Address
※Please turn to Dome Address Setup for details