Copernicus ELS1 User manual

ELS1 - Version A - 17 February 2012 - Copernicus Educational Products Inc.
Early Learning Centre
Assembly Guide
ELS1_2012_A
Check out our other products online at
www.copernicused.com
?This product is meant to be assembled by an adult.
?In its unassembled state, small parts present a hazard.
?To be used under direct supervision of an adult.
WARNING
For assistance, please contact us:
1-800-267-8494
Email [email protected]
Have your packing slip ready for reference
ELS1
Please Recycle
Tub Rack
1x
Safety Cap
1x
Knobs
2x
Bracket
2x
White Board Frames
(one with lines one without)
2x
Open Tubs
2x
Chart Loop Hooks
2x
Chart Hooks
2x
2" Twin Wheel
Locking Casters
4x
Roll Up Felt
Bottom Stretcher
Surface
2x
1x
Book Ledge
Warranty
Tub
Warranty
Life
Time
Frame
10
Year
Don’t forget to check out our tips for your whiteboard at:
www.copernicused.com

ELS1 - Version A - 17 February 2012 - Copernicus Educational Products Inc.
White Board Frames
(one with lines
one without)
2x
Tub Rack
1x
Knobs
2x
Nylon
Washer
4x
Assembly
Wrench
1x (Not to scale)
Bracket
2x
Open Tubs
2x
20mm
35mm
Bolt
Bolt
8x
4x
Lock
Washer
10x
Chart Loop
Hooks
2x
Chart Hooks
2x
2" Twin Wheel
Locking Casters
4x
Bottom Stretcher
2x
Contents - Box 2
Safety Cap Book Ledge
1x
Hardware
Actual Size
Before beginning, you should have:
Additional tools required:
Adjustable wrench Rubber Mallet
In Box 1
Early Learning Centre - Parts
Contents - Box 1
Roll Up Felt
Surface
1x

ELS1 - Version A - 17 February 2012 - Copernicus Educational Products Inc.
2 Install Casters
5 Install Book Ledge
1 Install Bottom Stretcher
3 Attach Brackets
-
-
Orient each stretcher with channel up
Fasten to each Whiteboard Frame with
two Large bolts & lock washers
- Repeat for other Whiteboard Frame
NOTE: Do not tighten any fasteners until the unit is fully assembled
3
NOTE: Ensure that the
triangle end of the Bracket is
used on the same side that
the Knobs are used to fasten
the Tub Rack to the Frame
Front Frame
Rear Frame
4
Nylon Washers
- Align the loops of the Tub Rack with the bottom holes
in the rear Whiteboard Frame
- Fasten to the rear Whiteboard Frame using two small
bolts & four nylon washers
- Align the other loops of the Tub Rack with the bottom
holes in the front Whiteboard Frame
- Fasten with Knobs
4 Install Tub Rack
- Insert one hook into one of the three hole positions in one
side of the Whiteboard Frame
- Pull out the opposite hook & snap into place
(Note: the spring tension is designed to discourage
children from unhooking the Book Ledge)
Snap
6 Snap the Hooks onto the Front & Rear Frames
7 Book Tubs on the Tub Rack
8 Place Felt Surface on
- Place the empty hardware bag over frame to prevent scratching
- Insert from the sides
desired Whiteboard
- Place Whiteboard Frame upside down
- Push caster stem into the caster insert
- Tap in with a mallet if necessary
- Repeat for other Whiteboard Frame
- Place Whiteboard Frames on their sides facing away
from each other
- Select one to be the front
- Align Bracket with the triangle end over the two holes
on the front Whiteboard Frame
- Fasten the Bracket to the front Whiteboard Frame
with two 20mm bolts & lock washers
- Align the hole on the back of the Bracket with the top
hole on the rear Whiteboard Frame
- Fasten to the rear Whiteboard Frame with 20mm bolt
& lock washer
- Repeat for other side of Whiteboard Frames,
ensuring that the Bracket points in the same direction
Don’t forget to check out our tips for your whiteboard at:
www.copernicused.com