Coram Showers 760 User manual

GB 71812 00 / Issue 3 / 15
CUSTOMER CARELINE 01746 713410
Equipment needed:
Drill, 6.5mm Masonry Bit, 4.5mm & 3mm Metal Bits (general), Crosshead Screwdriver, Right Angle, Fine Tooth Saw,
Spirit Level, Pencil, Scissors, Silicone Sealant, Tape Measure, Masking Tape.
Note: The screws and wall plugs supplied are for masonry walls. For lightweight walls i.e. stud partition, plasterboard etc,
use the correct type of fixings.
CORNER ENTRY
SHOWER ENCLOSURE
Please read these instructions carefully and keep for future reference.
Incorrect fitting will invalidate the guarantee.
SAFETY
●Handle glass with great care. Although the glass is very tough, sharp impacts can damage both the glass
and metal frame.
●Make sure there are no hidden pipes or cables hidden in the wall where you intend to drill.
●Wear safety goggles, shoes and appropriate clothing.
BEFORE INSTALLATION
●Two people are needed to carry out parts of the procedure, lift with care.
●Check that the shower tray is level in all directions. The enclosure will not sit correctly on an uneven surface.
If uneven, the wall channels may not fit and the doors may not shut correctly.
●The shower tray and the enclosure must match in size. Attempting to fit the incorrect size of enclosure to the
shower tray will result in water leaks.
●The enclosure should be fitted on tiled walls which are sealed with waterproof grout.
There must be a good silicone seal between the rim of the shower tray and the wall.
●Always check very carefully that components are vertical.
●To avoid damage, use the opened out packaging to build the enclosure on.
760 Door X = 740 - 760mm
800 Door X = 780 - 800mm
DIMENSIONS
Check the enclosure size in
the table below matches the
showertray installation.
X X

2
=
=
=
100mm
max
100mm
max
ø 4.5
mm
PN10676 PN10676
a: Drill holes in both wall channels (PN10676) at points shown using a 4.5mm drill bit, through the middle and in the groove.
b: Ensure the shower tray is level in all directions.
IMPORTANT: Clean the tray and seal the gap between the tray surface and tiles. It is important that the tray is sealed right up to
the tray edge so that the bottom of the wall channel is sealed. Failure to do this will cause water to leak under the wall channel
and between the tray and tiles, resulting in damp patches on the wall and under the tray.
1a b
Check contents of pack before installation. If anything is
missing, contact our Customer Careline for assistance.
CUSTOMER CARELINE: 01746 713410
8
PN3230
24
PN3225
4
6
14
PN4748
4
2
4
PN50489
PN60517
PN50488
PN50486
PN50487
PN60524
2
2
2
2
2
1/1
4
PN60518
760 RAIL - PN11154
800 RAIL - PN11155
760 RAIL - PN11156
800 RAIL - PN11157
760 RAIL - PN11154
800 RAIL - PN11155
760 RAIL - PN11156
800 RAIL - PN11157
10mm
32mm
2/2
PN60511
PN60521
Bottom
wheels
PN40333
PN40260
PN40095
PN80564
Top
wheels
9mm
Flipper
12mm
Flipper

2
3
a: Place the wall channels on the tray ensuring they are vertical and an equal distance back from the front of the tray.
Place masking tape against the wall before marking drill hole positions, this will help prevent the drill bit slipping. Drill 6.5mm
holes, 30mm deep and insert the wall plugs.
b: Apply sealant to the back of the wall channels. c: Fix the wall channels to the walls using 8 x 32mm screws.
a b c
a: Trim four horizontal fixed panel seals (PN40333) to length: 760 Model = 268mm - 800 Model = 288mm.
b: Fit trimmed seals to top and bottom of both fixed panels. Important: Seal 'flipper' must be on inside of panel.
The seals must be tight up against the metal. Note: Wetting the glass with water will help fit the seals.
3a b
32mm
X
ø 6.5
mm
X = Door widths
760 Model = 740mm - 760mm
800 Model = 780mm - 800mm
X
Trim 4x PN40333
760 Model = 268mm
800 Model = 288mm
Inside
Inside
Gap
PN40333
PN40333

6
Carefully position the assembled fixed panels into the wall
channels as shown.
Attach the corner joints to the top and bottom horizontal
rails using 32mm screws.
Push fit the corner joint covers.
Inside
Inside
4
Attach horizontal rails to top and bottom of both fixed
panels using 2 x 32mm screws.
Important: The rails are 'handed' in pairs, the hole in the
rails must be on the inside next to the vertical channel.
4
a: Important: Carefully open a gap between the fixed panel
and the bottom rail and apply sealant to the front and edge of
the glass up to the 'flipper seals' as shown.
b: Attach a glass clamp to each horizontal rail (at edge of
glass) using 10mm screws, tighten by hand only - do not
overtighten. Push fit glass clamp covers.
5
PN50489
PN50488
7
PN50486
PN50487
Inside
32mm
Hole
10mm
32mm
32mm
a
c
b
Inside of
fixed panel
a
b
Inside
Inside

9
Select the vertical seals with the 12mm flipper (PN40095) and trim
to 1717mm.
Fit trimmed seals to both fixed panels, seals must sit tight against
glass clamps (top and bottom).
Important: Seal 'flippers' must be on inside of the enclosure.
Note: Wetting the glass with water will help fit the seals.
Ensure sides are vertical.
Drill inside wall channels using 3mm drill bit where
shown. Do not drill too deep. Fix using 10mm screws
and screw caps.
8
5
ø 3
mm
10
Fit the door handles to the doors ensuring the plastic washers are fitted each side of the glass.
Inside
Inside
9mm
12mm
PN40095
Trim to
1717mm
10mm
PN60511

6
12
a: Select the vertical seals with the 9mm flipper (PN40260), magnetic seals (PN80564) and trim to 1785mm.
Push fit trimmed 'flipper seals' onto the back edge of the doors. Ensure the flipper seal 'flaps' are on the outside of the doors.
b: Push fit 'magnetic seals' (PN80564) onto the closing edge of the doors (the same side as door handle).
Note: Ensure the magnetic seals are positioned as shown.
Note: Wetting the glass with water will help fit the seals.
11
Important: Ensure that the coated side of the glass is on the inside of the door.
Attach the wheels to the doors: Adjuster wheels (PN60517) at the top and plunger wheels (PN60518) at the bottom.
Attach as shown and fix using the screw and screw cap (bottom 'plunger wheels' are shown as an example).
9mm
PN40260
Trim to
1785mm
PN80564
Inside
face of
door
PN40260
Inside
face of
door
PN80564
Inside
a
b
IMPORTANT
Ensure that the coated
side of the glass is on
the inside of the door.
PN60518
Inside face
of door
Bottom 'plunger wheels' are shown as an example.
PN60518
PN60518
PN60517
PN60517
PN60517
PN60517
PN60518
PN60518
Trim to
1785mm

7
Door adjustment: The wheels at the top of the doors may need adjusting so that the doors slide freely and the magnetic seals
meet evenly when the doors are closed.
a: From outside the enclosure and with the doors closed, adjust the screws on the top wheels. The bottom wheels should be
securely located in the bottom rail but the door must not be raised so high that the 'plungers' on the bottom wheels do not
operate.
b: The 'plungers' on the bottom wheels can be pushed down to unclip the doors which will allow access to clean the doors and
fixed panels.
14
From inside
a
b
From inside the enclosure, position the top wheels into the top rail, push down the 'plungers' on both bottom wheels and position
into the bottom rails.
13
From inside
Top of doors
Bottom of doors
Adjust
from
outside
Magnetic
seals

16
From the outside only, apply sealant to the bottom of the enclosure and 50mm up the wall channels and vertical joints
as shown.
CORAM SHOWERS LTD
Stanmore Industrial Estate, Bridgnorth, Shropshire WV15 5HP, UK •Tel: [phone] •Fax: [phone] • www.coram.co.uk
Recycling
Packaging:- The cardboard and polythene parts of this packaging can be recycled.
End of life:- This product contains materials such as aluminium and glass which can be recycled.
Please contact your local authority to find your nearest recycling centre.
IMPORTANT: You must not use the shower for 24 hours after installation of the enclosure.
DO NOT use bleach, scouring powders, solvents or other aggressive cleaning agents. To clean, use warm soapy water and a
clean cloth and rinse off.
Please note: There has been a glass coating applied to this product, use a squeegee to remove water and debris.
Periodically check all fixings and tighten if necessary.
Attach 4 x bumpstops (PN60521) to the holes at the ends of the top and bottom rails using 10mm screws and screw covers.
Ensure they are fitted the correct way up as shown. Note: If fitted incorrectly, they could cause the doors to jump out of the rail.
15
50mm
PN60521
10mm