Cornelius ABS 2.0 User manual

ABS 2.0 Operator’s Manual
Publication Number: 621058590OPR - 12 - © 2019, Cornelius Inc.
CLEANING / MAINTENANCE PROCEDURES
!
WARNING:
Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user.
Verify all power is off to the unit before performing any work
Failure to comply could result in serious injury, death or damage to the equipment.
CAUTION:
!
Do not use metal scrapers, sharp objects or abrasives on the ice storage hopper, top cover, agitator disc or
exterior surfaces. Do not use solvents or other cleaning agents as they may attack the material resulting in
damage to the unit
Soap solution – Use a mixture of mild detergent & warm (100°F) potable water.
Sanitizing Solution – Dissolve 1 packet [1oz. (29.6 ml)] of Kay - 5 or Stera Sheen Green Label into 2.5 gallons (9.46
L) of warm [80 - 100°F (26.7 - 37.8°C)] potable water to ensure 100 ppm of chlorine.
DAILY CLEANING AND SANITATION
1. Check the temperature, smell, and taste of the product.
2. Check the water pressure coming to the unit using a pressure gauge on the back room package, it
should be same as mentioned in Table 3 on page 6.
3. Check carbonation of the drink visually or by tasting.
4. Using a pressure gauge check the inlet pressure CO2or air supply to the system, it should be same as
mentioned in Table 3 on page 6 .
5. Check the date on all of the BIB’s (bags in boxes).
Locate Required Tools
•Soap Solution
•Paper Towel
•Clean Cloth
•Carbonated Water
•Sanitizing Solution
•Sanitizing Bucket
•Clean Sanitized Cloth

ABS 2.0 Operator’s Manual
© 2019, Cornelius Inc. - 13 - Publication Number: 621058590OPR
STAGING CLEANING
Dis-assemble Staging
1. Unscrew the 3 thumb screws holding the screw
in place as shown in Figure Figure 11. and
remove the cover.
Figure 11.
2. Remove the conveyor by lifting it up as shown in
Figure Figure 12.
NOTE: Do not carry conveyor by cup
holder.
Figure 12.
3. Remove the cup rest by lifting it up as shown in
Figure Figure 13.
Figure 13.

Clean Drip-Tray Area
1. Make sure water deflector is properly installed,
this will help prevent motor failures. (Order
replacement if the deflector is missing) as shown
in Figure Figure 14.
Figure 14.
2. Pour warm (NOT HOT) water down the drip-tray
drain. Flush the drip-tray using carbonated water
as shown in Figure Figure 15.
Drain line
Figure 15.
3. Wash the drip-tray area, splash panel and clean
any spills from the machine exterior using Soap
Solution with a clean cloth as shown in Figure
Figure 16.
Figure 16.
ABS 2.0 Operator’s Manual
Publication Number: 621058590OPR - 14 - © 2019, Cornelius Inc.

ABS 2.0 Operator’s Manual
© 2019, Cornelius Inc. - 15 - Publication Number: 621058590OPR
4. Wipe down drip-tray and splash panel with a
clean cloth to remove any soapy residue as
shown in Figure Figure 17.
Figure 17.
5. Spray Sanitizing Solution all around drip-tray and
splash panel. Let air dry for 5 minutes.
Figure 18.
Clean Conveyor & Grille
1. Wash the conveyor and grille in lukewarm soapy
water. Rinse with plain water as shown in Figure
Figure 19.
NOTE: Do not use hot water or place in
dishwasher.
Figure 19.