Cornelius IDC Pro Programming manual

Cornelius IDC PRO
Cleaning Instructions
& Trouble Shooting

NOZZLES AND DIFFUSERS - DAILY CLEANING
Remove the nozzles from the dispenser by turning each
nozzle to the left and pulling down.
Remove the inner diffusers by pulling down; separate the
clear gasket from the diffuser.
Note orientation of gasket for reinstallation (shown on
page 4)

NOZZLES AND DIFFUSERS - DAILY CLEANING
Clean the diffusers, nozzles and gaskets thoroughly
with the nylon bristle brush and soapy water. Rinse
them with water.
Put the nozzles, gaskets and the diffusers in
sanitizer solution for one minute. Don’t over soak
or they will dry out.
Remove the nozzles, gaskets and diffusers from the
solution and allow them to air dry.

NOZZLES AND DIFFUSERS –DAILY CLEANING
Install the gasket into the diffuser. Line
up the two notches on the inner circle
of both the gasket and diffuser.
Push the silicone gasket into the
diffuser.
Make sure that the raised side of the
clear gasket is face-up when re-
inserting the diffuser.
Note: If the clear gasket is upside
down, the notches will not line up
right.
4

NOZZLES AND DIFFUSERS - DAILY CLEANING
Brush the diffuser area under the machine
thoroughly with a nylon bristled brush.
Wipe under side of valves with sanitizer
cloth.
Allow to air dry.

NOZZLES AND DIFFUSERS –DAILY CLEANING
Re-install the inner Diffuser and Gasket into nozzle
base by rotating slightly while pushing up.
Re-install outer nozzle and twist to lock in place
NOTE: Ensure the outer nozzle is on STRAIGHT when
locking.
Make sure nozzle locks. Purge valve to remove any
remnant sanitizer by running a water cycle for 10-15
seconds.

CLEANING ICE CHUTE
Clean the interior of the ice chute using the
brush provided with the unit.
Use warm soapy water, rinse with clear (not
soapy), water using brush, then do a final rinse
using the brush with sanitizer water.
Let air dry.
7

CLEANING THE SCREEN, MACHINE &
DRAIN
Clean the screen using a sanitized towel, then
wipe face with dry towel. Refer to page 11 on
how to lock screen during cleaning.
8
Clean the remainder of the machine using a
sanitized towel. Clean drip tray grate in sink.
Clean the drain WEEKLY using a bucket filled
with 1-2 gallons of warm water and a capful
of bleach.

ACCESSING THE MENU’S
Display the keypad screen by tapping
each corner of the video screen
starting in the upper right corner and
continuing to tap each corner in a
counter clockwise direction, in the
form of a “C”.
This will display the Key pad screen.
Once each corner is tapped, type in the
password “1111” then press Enter to access the
Operator menu.
9
1
2
4
3

SCREEN CLEANING LOCKOUT
The screen cleaning lockout screen allows you to clean the digital merchandiser
without dispensing product.
Touch inside the circle to activate the 20 second lockout.
Select Screen Cleaning Lockout Screen Cleaning 20sec Lockout Screen
10

SOLD OUT SYRUP
11
The “Sold Out” application allows you to place a “Sold Out” logo over the
brand that is sold out.
Be sure to hit “Save” before exiting. To unmark, hit the brand again and hit
“Save” before exiting.
11

TROUBLE SHOOTING
If the screen freezes up –press the red
reset button. If nothing happens, hold that
button in for 5 seconds until the screen
goes black, wait 10 seconds and press
button again to restart.
If the machine does not have a red reset
button, gently disconnect the gray
connectors and then reconnect them
together.
12
If the machine does not dispense ice –
make sure the door is completely closed
on both sides.