Cornelius Post-Mix Valves UFB-1 User manual

Operator manual
Dispensing valve
UFB1
PUSH

Legal notice
Operator manual (Original)
Document no. TD2004000
Dispensing valve
UFB1 portion control: Part number: 741000401 (3 oz)
UFB1 push button: Part number: 741000399 (3 oz) | 740001214 (4 oz)
UFB1 dispensing lever: Part number: 741000403 (3 oz) | 740001213 (4 oz)
UFB1 OptiFill: Part number: 741000405 (3 oz)
UFB1
Version
Date of issue: 15/03/2019
Revision status: Index 0
www.cornelius-emea.com Cornelius Deutschland GmbH
Carl-Leverkus-Str. 15
40764 Langenfeld
Germany
Tel.: [phone]
Fax: [phone]
E-Mail: [e-mail]
Protection notices (in accordance with DIN ISO 16016:2017-08)
The reproduction, distribution and utilisation of this document as well as the communication of
its contents is prohibited, unless expressly permitted. Violations shall result in an obligation to
pay damages. All rights reserved with regard to filing for/registering patents, utility models or
design patents.
Obligation to preserve records
Please keep this Operator Manual and the Declaration of Conformity in a safe place and trans-
fer them to the subsequent owner/operator if the dispensing valve is transferred or sold.
If you lose the Operator Manual or the Declaration of Conformity, you can download them from
the website below or request a printed copy from the address below.

Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
1
Operator manual
Dispensing valve
Table of contents
1 Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Improper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Staff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3.1 Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3.2 User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3.3 Expert. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 Presentation of warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.5 Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.5.1 Disclaimer of liability and warranties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.5.2 Safety information to prevent personal injury and equipment damage. . . . . . . 7
2 Handling the dispensing valve prior to installation . . . . . . . . . . . . . . . . . 8
2.1 Unpacking the dispensing valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Transport and packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1 Dispensing valve UFB1 portion control . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2 Dispensing valve UFB1 push button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.3 Dispensing valve UFB1 dispensing lever . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.4 Dispensing valve UFB1 OptiFill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3.5 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.5.1 Dispensing valve UFB1 portion control . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.5.2 Dispensing valve UFB1 push button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.5.3 Dispensing valve UFB1 dispensing lever . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.5.4 Dispensing valve UFB1 OptiFill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
3.5.5 Soda lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.6 Dispensing nozzles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.6.1 Standard dispensing nozzle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.6.2 Juice dispensing nozzle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.7 Functions within the dispensing system. . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.8 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.8.1 Dispensing valve UFB1 portion control . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.8.2 Dispensing valve UFB1 push button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.8.3 Dispensing valve UFB1 dispensing lever . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
2
3.8.4 Dispensing valve UFB1 OptiFill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
4 Dispensing beverages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1 Dispensing beverages in “TIME BASED” mode. . . . . . . . . . . . . . . . . . . . . . 20
4.1.1 Dispensing valve UFB1 portion control . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.2 Dispensing beverages in “START & STOP” mode . . . . . . . . . . . . . . . . . . . . 20
4.2.1 Dispensing valve UFB1 portion control . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.2.2 Dispensing valve UFB1 push button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2.3 Dispensing valve UFB1 dispensing lever . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2.4 Dispensing valve UFB1 OptiFill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
4.2.5 Soda dispensing (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.1 Maintenance table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.2 Visually inspecting the dispensing valve . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.2.1 Visually inspecting the dispensing nozzle. . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.3 Cleaning the dispensing valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.3.1 Cleaning the dispensing nozzle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
6 Errors and malfunctions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.1 Troubleshooting table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7 Applicable documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7.1 Handover certificate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Safety
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
3
1Safety
1.1 Intended use
By using the unit as intended you will not only protect yourself, but also prevent damage oc-
curring to the dispensing valve and its components!
Dispensing valves from the UFB1 series (referred to as “dispensing valve” in the following) are
intended for use as dispensers of non-alcoholic beverages and their basic ingredients.
The dispensing valve is only suitable for installation on a base unit. Installation is to be carried
out by an expert in compliance with all of the specifications given in the installation and service
manual; see the document “Dispensing valve installation and service manual”, document no.
TD2004100.
The unit may only be operated in the specified ambient conditions, see chapter 3.8.
In particular, intended use means that you will carry out all activities with and on the dispensing
valve to the specifications provided in this document.
This dispensing valve is only to be operated by those who meet the requirements set out in
this document; see chapter 1.3.2.
Work on the dispensing valve and its components not included in the activities described in
this document may only be performed by experts; see chapter 1.3.3.
1.2 Improper use
Improper use of the dispensing valve, and unauthorised modifications to the dispensing valve
and its components may cause personal injury and equipment damage for which Cornelius
Deutschland GmbH shall assume no liability. Improper use of the dispensing valve is prohibit-
ed.
The following in particular is regarded as improper use:
– Use by persons (including children) with physical, sensory or mental disabilities or those
with insufficient experience and knowledge, unless they are supervised by a person re-
sponsible for their safety, or this person has instructed them in the use of the unit.
– Use, operation and maintenance by children under 8 years.
– Children are not to play with the dispensing valve. Cleaning and maintenance work must
not be carried out by children unattended.
– Use by those under the influence of medication, alcohol, drugs or other substances which
impair their physical, sensory or mental abilities.
– Operation below the minimum and above the maximum ambient temperature (for mini-
mum and maximum temperatures, see chapter 3.8).
– Operation of the dispensing valve by untrained staff.
– Carrying out cleaning and other types of maintenance work on the dispensing valve which
contradict this document or are not included in it.

Safety
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
4
1.3 Staff
1.3.1 Operator
The operator is the natural or legal person who uses the dispensing valve or on whose behalf
the dispensing valve is used. The operator must ensure that the dispensing valve is only used
as intended, in observance of the safety instructions set out in this document.
The operator must ensure that all users read and understand the safety information. The op-
erator is responsible for the planning and proper implementation of regular safety inspections
and maintenance work.
With regard to operating the dispensing valve, Cornelius Deutschland GmbH recommends ob-
serving the national regulations of the country of use which govern the operation of beverage-
dispensing systems.
1.3.2 User
The operator specifies who will operate this dispensing valve. Cornelius Deutschland GmbH
recommends the following:
– If this dispensing valve is only to be operated by employees, they are to be instructed in
its use, demonstrate their abilities to use it to the operator or their authorised representa-
tive, and be expressly charged with its use. This document is to be available to staff at all
times.
– If this dispensing valve is openly accessible and installed so that untrained staff can use
it, the operator is to provide instructions for use directly at the base unit; these must be
clearly understood by this group of people, therefore ensuring that the unit will be handled
safely.
1.3.3 Expert
An expert in terms of this document refers to someone who has the relevant training, experi-
ence and information and knowledge of relevant standards, laws, regulations, accident pre-
vention regulations, generally accepted safety-related regulations and operating conditions to
be able to perform the required activities as well as recognise potential risks and avert them.
For assignments requiring expert knowledge, e.g. in electrical engineering, mechanics or fluid
technology, only skilled workers with the right qualifications are to carry these out.
An expert must also have received technical training in the specific special features of Corne-
lius products. The assigned tasks are always to be carried out in compliance with the relevant
installation and service manual for the dispensing valve concerned; see the document “Dis-
pensing valve installation and service manual”, document no. TD2004100.

Safety
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
5
1.4 Presentation of warnings
The classification of warnings is based on ISO 3864-2 and ANSI Z535.6, using the key terms
of1
– “Danger”, “Warning” and “Caution” in the case of personal injury,
– “Attention” in the case of equipment damage and
– “Notice” to impart general information.
This document classifies and presents the various pieces of safety information as follows:
DANGER!
marks a danger with a high risk2, which will result in serious injury or death
if not avoided.
WARNING!
marks a danger with a medium risk2, which may result in serious injury or
death if not avoided.
CAUTION!
marks a danger with a low risk2, which may result in minor to moderate in-
jury if not avoided.
ATTENTION!
marks a potentially damaging situation in which the product or objects may
be damaged if not avoided.
NOTICE!
marks tips for use and other particularly useful information that may not be
recognised at first glance.
SAFETY INFORMATION!
marks safety information which must be observed in the stated operating
situation.
1Not all of the following key terms need to be used in this documentation.
2Risk = extent x likelihood of occurrence

Safety
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
6
1.5 Safety information
Any work on the dispensing valve and its components which goes beyond the operation and
servicing and maintenance that the operator is authorised for, may only be performed by ex-
perts (for a definition of experts, see chapter 1.3.3). Furthermore, it is crucial that when per-
forming work on the dispensing valve all safety information is observed; this information is set
out in the following sections. Some of the tasks may have additional safety information which
highlights the specific dangers or hazards associated with such work.
1.5.1 Disclaimer of liability and warranties
If work is undertaken on the dispensing valve which is not described in this document, Corne-
lius Deutschland GmbH shall not assume any liability for any resulting hazards and damages.
The same applies to described work which is partly or not fully performed in compliance with
the regulations set out in this document.
WARNING!
Risk of personal injury and equipment damage due to improperly ex-
ecuted work!
Improperly executed work at the dispensing valve will cause dangers to
persons and damage to the unit.
• Have all work at the dispensing valve carried out by Cornelius
Deutschland GmbH or by a service partner.
WARNING!
Risk of personal injury and equipment damage due to the use of non-
approved spare parts and accessories!
Using spare parts and accessories that are not recommended by the man-
ufacturer may lead to personal injury and equipment damage.
• For your own safety and to protect your warranty, only use original
spare parts.

Safety
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
7
1.5.2 Safety information to prevent personal injury and equip-
ment damage
Please always observe the following safety information in order to prevent personal injury oc-
curring:
DANGER!
Risk of death from electric shock!
Touching live electrical parts will result in a risk of electric shock!
• Do not carry out any work on the electrical system.
WARNING!
Risk of personal injury and equipment damage due to improper oper-
ation!
Risk of death from improper operation!
• Make sure that only users who are users as defined in the user section
use the dispensing valve; see chapter 1.3.2.
• Children must be supervised to ensure that they do not play at or with
the dispensing valve.
NOTICE!
In particular, safety standards are to be observed in their scope of validity
(e.g. EN 60335-2-75).

Handling the dispensing valve prior to installation
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
8
2 Handling the dispensing valve prior to installation
2.1 Unpacking the dispensing valve
NOTICE!
Cornelius Deutschland GmbH is not responsible for damaged deliveries. If
any damage is found, all packaging material is to be kept and the freight
carrier is to be contacted. If the freight carrier is not contacted within 48
hours of receipt of delivery, the warranty claim might be rendered void.
NOTICE!
The dispensing valve is thoroughly checked ex works before being
shipped. The freight carrier has confirmed and acknowledged receipt. All
damage or irregularities are to be noted at the time of delivery and reported
immediately to the freight carrier delivering. Please request a written in-
spection report from the claims inspector to substantiate any claim.
1. Inspect the cardboard box and make a note of any damage however minimal this may
seem. If the cardboard box is damaged, please make a note of the following on the copy
of your freight invoice: “exterior cardboard box damage – concealed damage possible”.
Please contact the freight company immediately.
2. Open the cardboard box, packaging material and plastic bag in which the dispensing valve
is packed. Check the dispensing valve thoroughly for damage and to make sure it is com-
plete in accordance with table 2-1.
3. Remove the packaging material from the top of the dispensing valve.
4. Check the dispensing valve cladding and make sure that there are no scratches, dents or
other superficial defects.
5. Make sure that the glass or plastic has no scratches or cracks.
6. Open the package with the loose individual parts and check all parts for damage and com-
pleteness. Check that the received parts correspond with the packing list and make sure
that you have received all parts.
Tab. 2-1 Cardboard box content
No. Description Qty/amount
1 Operator manual, and installation and service manual 1
2 Dispensing valve 1

Handling the dispensing valve prior to installation
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
9
2.2 Storage
Avoid excessive temperature fluctuations as condensate may form, which in turn may cause
damage to the dispensing valve or to its components.
The permissible storage temperature is -10 °C to +50 °C.
The acclimatisation period is 6 hours.
ATTENTION!
Damage due to improper storage!
Dirt or moisture entering a dispensing valve, as well as certain weather con-
ditions (e.g. condensate forming in the dispensing valve, sunlight) will
cause damage to the dispensing valve and its components.
• Protect the dispensing valve and its components by storing the dis-
pensing valve in a clean and dry place, and by ensuring stable ambient
conditions.
• If possible, store the dispensing valve in its original packaging. Un-
packed dispensing valves must be covered with a dustproof cover. No
condensate must form under the cover.
ATTENTION!
Risk of electrostatic charge!
Improper handling or storage may result in electrostatic charges.
• If possible, store dispensing valves and/or any electronic components
in their original packaging.
• Keep dispensing valves and/or electronic components away from
charged objects, fields and insulators.
• Avoid electrostatic charges when removing packaging and/or handling
electronic assemblies and components by working at an ESD-protect-
ed workstation or work area.
• When working at the unit or its components, wear a grounding (anti-
static) wrist strap at the very least and wear antistatic gloves if neces-
sary.
ATTENTION!
Component damage due to material ageing!
Material can age due to long storage periods, thereby affecting the materi-
al’s properties (e.g. plastics and seals may become brittle). The properties
of lubricants may change due to long storage periods.
• Check the assemblies and components for damage before each use/
before installing them. Do not install assemblies or components that
show visible signs of ageing.

Handling the dispensing valve prior to installation
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
10
2.3 Transport and packaging
Choose a suitable packaging when returning the dispensing valve itself or one of its compo-
nents to Cornelius Deutschland GmbH, e.g. for repairs. In particular, make sure that the dis-
pensing valve and any components are protected from shock/impact, moisture, dirt and
electrostatic discharge (ESD). This will prevent transport damage to the dispensing valve and
to the components, for which the manufacturer shall assume no liability.
ATTENTION!
Component damage due to freezing liquids!
Ambient temperatures that are below freezing will lead to the freezing of
any water or cleaning agent residue remaining inside the dispensing valve.
This will lead to damage to internal components.
• Before shipment, storage or relocation, the dispensing valve is to be
cleaned and the cleaning solution is to be fully drained from the dis-
pensing valve.
2.4 Disposal
Disposal of the dispensing valves must be carried out in compliance with the applicable local
and/or national and international regulations. Units must not be disposed of with household
waste.
If the dispensing valve contains fuels or lubricants in liquid, paste-like or gaseous form, such
as oil, grease, cooling agents etc., such fuels or lubricants are to be collected using appropriate
measures and disposed of in compliance with the applicable local and/or national and interna-
tional regulations. Such fuels or lubricants must always be prevented from seeping into the
ground, the sewage system and any bodies of water, and must always be prevented from en-
tering the atmosphere.

Description
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
11
3 Description
The dispensing valve UFB1 is available in the following designs:
• Dispensing valve UFB1 portion control; see chapter 3.1.
• Dispensing valve UFB1 push button; see chapter 3.2.
• Dispensing valve UFB1 dispensing lever; see chapter 3.3.
• Dispensing valve UFB1 OptiFill; see chapter 3.4.
For the dispensing valve UFB1, a soda lever is available as an option, which allows dispensing
purely of soda, see chapter 4.2.5.
3.1 Dispensing valve UFB1 portion control
Via the dispensing valve UFB1 portion control, a “TIME BASED” dispensing is possible by ac-
tuating the required button, see chapter 4.1.1. The beverage is dispensed for a specified time
according to the cup size selected. Four different cup sizes can be programmed for the dis-
pensing valve UFB1 portion control. Please contact your service partner.
Via the dispensing valve UFB1 portion control , “START & STOP” dispensing is additionally
possible by pressing the “Start & Stop” button, see chapter 4.2.1.
The dispensing valve UFB1 portion control comprises the following components:
Fig. 1/1 Control panel
Fig. 1/2 Dispensing nozzle
Fig. 1
PGM
WAIT
1
2

Description
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
12
3.2 Dispensing valve UFB1 push button
Via the dispensing valve UFB1 push button, “START & STOP” dispensing is possible by press-
ing the “PUSH” button, see chapter 4.2.2.
The dispensing valve UFB1 push button comprises the following components:
3.3 Dispensing valve UFB1 dispensing lever
Via the dispensing valve UFB1 dispensing lever, “START & STOP” dispensing is possible by
actuating the dispensing lever, see chapter 4.2.3.
The dispensing valve UFB1 dispensing lever comprises the following components:
Fig. 2/1 Control panel
Fig. 2/2 Dispensing nozzle
Fig. 2
PUSH
1
2
Fig. 3/1 Dispensing nozzle
Fig. 3/2 Dispensing lever
Fig. 3
2
1

Description
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
13
3.4 Dispensing valve UFB1 OptiFill
Via the dispensing valve UFB1 OptiFill, “START & STOP” dispensing is possible by actuating
the dispensing lever, see chapter 4.2.4.
The dispensing valve UFB1 OptiFill features a safety mechanism. This safety mechanism pre-
vents the beverage from overflowing as soon as the beverage or foam touches the dispensing
lever.
It is also possible to activate a follow-up time. Once the dispensing process has been interrupt-
ed, if the cup is still standing on the drip tray of the base unit and is pressing against the dis-
pensing lever, it is restarted after a programmed time.
The dispensing valve UFB1 OptiFill comprises the following components:
3.5 Controls
3.5.1 Dispensing valve UFB1 portion control
Fig. 4/1 Dispensing nozzle
Fig. 4/2 Dispensing lever
Fig. 4
2
1
Fig. 5/1 “XL” button
Fig. 5/2 “L” button
Fig. 5/3 “Start & Stop” button
Fig. 5/4 “M” button
Fig. 5/5 “S” button
Fig. 5
PGM
WAIT
5 4
3
2 1

Description
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
14
3.5.2 Dispensing valve UFB1 push button
3.5.3 Dispensing valve UFB1 dispensing lever
Fig. 6/1 “PUSH” button
Fig. 6
PUSH
1
Fig. 7/1 Dispensing lever
Fig. 7
1

Description
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
15
3.5.4 Dispensing valve UFB1 OptiFill
3.5.5 Soda lever
3.6 Dispensing nozzles
The beverage components flowing from the valve are fed to the baffle with diffusor in the dis-
pensing nozzle and mixed there. From there, they are poured into the cup via the dispensing
nozzle.
Multiple dispensing nozzles are available for the dispensing valve UFB1.
• Standard dispensing nozzle, see chapter 3.6.1.
• Juice dispensing nozzle, see chapter 3.6.2.
Fig. 8/1 Dispensing lever
Fig. 8
1
Fig. 9/1 Soda lever
Fig. 9
1

Description
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
16
3.6.1 Standard dispensing nozzle
The dispensing nozzle comprises the following components:
3.6.2 Juice dispensing nozzle
This dispensing nozzle is used exclusively for dispensing juice, and comprises the following
components:
3.7 Functions within the dispensing system
NOTICE!
The operator manual applicable to the base unit contains the description of
how the dispensing valve functions within a dispensing system.
Fig. 10/1 Standard baffle with diffusor
Fig. 10/2 Outlet nozzle
Fig. 10
1
2
Fig. 11/1 Juice baffle with diffusor
Fig. 11/2 Outlet nozzle
Fig. 11
1
2

Description
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
17
3.8 Technical data
3.8.1 Dispensing valve UFB1 portion control
3.8.2 Dispensing valve UFB1 push button
Description Parameter Value Unit
Dimensions
Height 140/5.5 mm/in.
Width 63.5/2.5 mm/in.
Depth 140/5.5 mm/in.
Flow rates 3oz valve 1.5 – 3 (45 – 90) oz/sec (ml/sec)
4oz valve 2 – 4 (60 – 120) oz/sec (ml/sec)
Ambient temperature 0 – 60 °C
Humidity 20 – 100 %
Power supply Supply voltage 24 V AC
Frequency 50/60 Hz
Shipping weight 20 pcs. 15.4 kg
Description Parameter Value Unit
Dimensions
Height 140/5.5 mm/in.
Width 63.5/2.5 mm/in.
Depth 140/5.5 mm/in.
Flow rate 3oz valve 1.5 – 3 (45 – 90) oz/sec (ml/sec)
4oz valve 2 – 4 (60 – 120) oz/sec (ml/sec)
Ambient temperature 0 – 60 °C
Humidity 20 – 100 %
Power supply Supply voltage 24 V AC
Frequency 50/60 Hz
Shipping weight 20 pcs. 15.4 kg

Description
Cornelius Deutschland GmbH
Document no. TD2004000
Version 15/03/2019, Index 0
Operator manual Dispensing valve
UFB1
18
3.8.3 Dispensing valve UFB1 dispensing lever
3.8.4 Dispensing valve UFB1 OptiFill
Description Parameter Value Unit
Dimensions
Height 241/9.5 mm/in.
Width 63.5/2.5 mm/in.
Depth 140/5.5 mm/in.
Flow rate 3oz valve 1.5 – 3 (45 – 90) oz/sec (ml/sec)
4oz valve 2 – 4 (60 – 120) oz/sec (ml/sec)
Ambient temperature 0 – 60 °C
Humidity 20 – 100 %
Power supply Supply voltage 24 V AC
Frequency 50/60 Hz
Shipping weight 20 pcs. 15.4 kg
Description Parameter Value Unit
Dimensions
Height 282.6/11.13 mm/in.
Width 63.5/2.5 mm/in.
Depth 140/5.5 mm/in.
Flow rates 3oz valve 1.5 – 3 (45 – 90) oz/sec (ml/sec)
4oz valve 2 – 4 (60 – 120) oz/sec (ml/sec)
Ambient temperature 0 – 60 °C
Humidity 20 – 100 %
Power supply Supply voltage 24 V AC
Frequency 50/60 Hz
Shipping weight 20 pcs. 15.4 kg