Cornelius CMP 600-30 User manual

CMP 600-30
ICE MAKER DISPENSER - CMP 600-30
Service Manual
Release Date: March 3, 2004
Publication Number: 630460050SER
Revision Date: March 18, 2014
Revision: C
Visit the Cornelius web site at www.cornelius.com for all your Literature needs.

The products, technical information, and instructions contained in this manual are subject to change without notice.
These instructions are not intended to cover all details or variations of the equipment, nor to provide for every possible
contingency in the installation, operation or maintenance of this equipment. This manual assumes that the person(s)
working on the equipment have been trained and are skilled in working with electrical, plumbing, pneumatic, and
mechanical equipment. It is assumed that appropriate safety precautions are taken and that all local safety and con-
struction requirements are being met, in addition to the information contained in this manual.
This Product is warranted only as provided in Cornelius’ Commercial Warrant applicable to this Product and is subject
to all of the restrictions and limitations contained in the Commercial Warranty.
Cornelius will not be responsible for any repair, replacement or other service required by or loss or damage resulting
from any of the following occurrences, including but not limited to, (1) other than normal and proper use and normal
service conditions with respect to the Product, (2) improper voltage, (3) inadequate wiring, (4) abuse, (5) accident, (6)
alteration, (7) misuse, (8) neglect, (9) unauthorized repair or the failure to utilize suitably qualified and trained persons
to perform service and/or repair of the Product, (10) improper cleaning, (11) failure to follow installation, operating,
cleaning or maintenance instructions, (12) use of “non-authorized” parts (i.e., parts that are not 100% compatible with
the Product) which use voids the entire warranty, (13) Product parts in contact with water or the product dispensed
which are adversely impacted by changes in liquid scale or chemical composition.
Contact Information:
To inquire about current revisions of this and other documentation or for assistance with any Cornelius product con-
tact:
www.cornelius-usa.com
800-238-3600
Trademarks and Copyrights:
This document contains proprietary information and it may not be reproduced in any way without permission from
Cornelius.
This document contains the original instructions for the unit described.
CORNELIUS INC
101 Regency Drive
Glendale Heights, IL
Tel: + 1 800-238-3600
Printed in U.S.A.

TABLE OF CONTENTS
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Read and Follow ALL Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Different Types of Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Qualified Service Personnel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Shipping And Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Mounting in or on a Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Icemaker Cleaning and Sanitizing Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Monthly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Quarterly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Semi–Annually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Water Level Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
How Water Level Control Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Purpose of Water Level Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
To Replace Water Level Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
To Replace Water Level Safety Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Ice Level Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Refrigeration Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Refrigeration System Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Expansion Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Adjustment and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Temperature/Pressure Charts* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Condenser Modulating Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Condenser Modulating Valve Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Gear Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Troubleshooting Gear Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
The Gear motor will not run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
The Gear motor Starts buts Trips Repeatedly on the Overload Protector: . . . . . . . . . . . . . . . . 13
The Motor Runs but Output Shaft does not Rotate:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Overload Check: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Motor Check: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Installation and Shaft Seal Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Auger & Extruding Head Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Auger & Extruding Head Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
To Replace Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Troubleshooting Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Electrical Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Overload Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Compressor Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Capacitor Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Safety Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Guide to Good Ice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

CMP600-30 Icemaker Dispenser Service Manual
© 2004-2014, Cornelius Inc. - 1 - Publication Number: 630460050SER
SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Safety Overview
• Read and follow ALL SAFETY INSTRUCTIONS in this manual and any warning/caution labels on the unit (decals, labels or
laminated cards).
• Read and understand ALL applicable OSHA (Occupational Safety and Health Administration) safety regulations before
operating this unit.
Recognition
DIFFERENT TYPES OF ALERTS
!
DANGER:
Indicates an immediate hazardous situation which if not avoided WILL result in serious injury, death or equipment
damage.
!
WARNING:
Indicates a potentially hazardous situation which, if not avoided, COULD result in serious injury, death, or equipment
damage.
CAUTION:
!
Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury or equipment
damage.
SAFETY TIPS
• Carefully read and follow all safety messages in this manual and safety signs on the unit.
• Keep safety signs in good condition and replace missing or damaged items.
• Learn how to operate the unit and how to use the controls properly.
• Do not let anyone operate the unit without proper training. This appliance is not intended for use by very young children or
infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.
• Keep your unit in proper working condition and do not allow unauthorized modifications to the unit.
QUALIFIED SERVICE PERSONNEL
!
WARNING:
Only trained and certified electrical, plumbing and refrigeration technicians should service this unit. ALL WIRING
AND PLUMBING MUST CONFORM TO NATIONAL AND LOCAL CODES. FAILURE TO COMPLY COULD
RESULT IN SERIOUS INJURY, DEATH OR EQUIPMENT DAMAGE.
Recognize Safety Alerts
This is the safety alert symbol. When you see it in this manual or on the unit,
be alert to the potential of personal injury or damage to the unit.
!

CMP600-30 Icemaker Dispenser Service Manual
Publication Number: 630460050SER - 2 - © 2004-2014, Cornelius Inc.
SAFETY PRECAUTIONS
This unit has been specifically designed to provide protection against personal injury. To ensure continued protection
observe the following:
!
WARNING:
Disconnect power to the unit before servicing following all lock out/tag out procedures established by the user. Verify
all of the power is off to the unit before any work is performed.
Failure to disconnect the power could result in serious injury, death or equipment damage.
CAUTION:
!
Always be sure to keep area around the unit clean and free of clutter. Failure to keep this area clean may result in
injury or equipment damage.
SHIPPING AND STORAGE
CAUTION:
!
Before shipping, storing, or relocating the unit, the unit must be sanitized and all sanitizing solution must be drained
from the system. A freezing ambient environment will cause residual sanitizing solution or water remaining inside the
unit to freeze resulting in damage to internal components.
CAUTION:
!
Very high discharges pressure is present in system. Quick disconnects on your gages will minimize danger and loss
of refrigerant.
CAUTION:
!
Unit requires separate electrical line. See instruction manual for proper fuse size.
!
WARNING:
There must be adequate clearance around ice maker. Allow minimum 6” air intake and 4” air exhaust for air exhaust
and panel removal.
NOTE: Unit must be installed per local plumbing and electrical codes. See Installation manual for
unit requirements. Failure to do so may cause damage to unit, which would void unit warranty.
NOTE: Using any parts other than genuine factory manufactured parts relieves the manufacturer
of all liability.
NOTE: Manufacturer reserves the right to change specifications at any time.

CMP600-30 Icemaker Dispenser Service Manual
© 2004-2014, Cornelius Inc. - 3 - Publication Number: 630460050SER
GENERAL INFORMATION
SPECIFICATIONS
Model Cond.
Unit VAC Hz. Ph. Wire Comp. RLA
Fan
Amps
Grmtr
Amps
Refrig. Circuit
Fuse
Oz. Type
CMP 600–30A Air Cooled 115 60 1 2 12 1 2 28 R404A 20
INSTALLATION INSTRUCTIONS
1. REMOVE ICEMAKER FROM CARTON:
A. Keep unit in the upright position, remove carton and pallet from unit and inspect unit for damage. Upon
inspection of unit, if any damage is found, file a claim with carrier immediately.
B. Locate Startup Card either on outside of container or on plastic liner. Fill in proper information and send
one copy to factory, and other copy to Distributor. Postage is prepaid.
2. PREPARATION OF INSTALLATION SITE:
A. The refrigeration system on air cooled units requires airflow, so a well ventilated area should be chosen. A
minimum of (6) inches must be maintained, free of any obstruction, for air intake. A minimum of (4) inches
clearance is required for air exhaust.
3. WATER INLET HOOK–UP:
A. Water Inlet – Fitting is a 1/4” SAE male flare located at the left rear bottom of the unit. Connect water sup-
ply with a 1/4”or larger copper or flexible tubing.
B. Water Pressure – Unless otherwise specified, the unit is designed to operate on water pressures between
10 P.S.I. and 90 P.S.I. (NOTE: for pressures above 90 P.S.I. a regulator must be installed).
C. Water Cooled Condensers
• Inlet to modulating valve uses 3/8” FPT. Use separate 3/8” or larger water line.
• Outlet is 3/8” FPT.
D. Filters – Filter/Conditioners are recommended on supply lines to icemakers. Never run the water supply to
water cooled Condenser through Filter/Conditioner, it uses up the cartridge unnecessarily and a saturated
cartridge can starve the icemaker causing premature component damage. Separate water supplies are
recommended.
NOTE: Unit must be installed per local plumbing code.
4. ELECTRICAL SUPPLY:
A. Power Access – Is provided by way of a 7/8” dia. hole in the base. Route incoming power in conduit, to
icemaker electrical control box.
B. Make connections to wires provided in control box and ground lug/screw. Plug unused hole.
C. Fused Line – Should be a dedicated circuit checked and sized according to electrical rating shown on unit
nameplate.
NOTE: Unit must be installed per local electrical code.
5. DRAIN CONNECTION:
A. Bin Drain– is a ” ID flexible tube located at the left bottom rear of the unit. Extend this line to proper drain.
B. Overflow Line– is a 3/8” ID flexible tube located at the left bottom rear of the unit. Extend this line to proper
drain.

CMP600-30 Icemaker Dispenser Service Manual
Publication Number: 630460050SER - 4 - © 2004-2014, Cornelius Inc.
6. AUGER ENGAGEMENT:
Be certain that auger is fully engaged to lower drive and that extruding head is fully engaged to evaporator.
7. INITIAL START UP, CHECKS & ADJUSTMENT INSTRUCTIONS:
NOTE: Do not start unit before completing Installation steps 1–6.
Turn on water supply and main power switch (located on top of electrical box). Make the following system checks:
NOTE: If unit will not start be sure water reservoir is full. Low water safety control must be properly
adjusted to start and shut down unit. If water level drops below bottom of reservoir, unit must shut
down. Adjustment is made by moving magnet up or down.
Figure 1. Water Reservoir
Water Level – If necessary adjust Float by bending float arm up or down as needed, push float assembly down until
unit stops running. Release float and unit will restart. Keep water in reservoir at level line while unit is in operation. See
Figure 1.
Low Water Safety Control – Adjust magnet by bending magnet arm as shown in Figure 1 to shut down unit if the
water level drops below the line on the side of the reservoir.
Bin Control – Remove four screws from top of bin cover and lift cover so bin control plate can be manually lifted until
unit shuts down. Release plate and unit will restart (NOTE: the dispense button must be depressed for 45
seconds before unit will start). Replace screws.
Dispense Switch and Mechanism – By depressing the dispense switch, the dispense mechanism door on the
storage bin will open, and agitator will rotate counterclockwise.
NOTE: If any of these checks or adjustments cannot be achieved, refer to Troubleshooting Section
of this manual or call our technical support center for assistance.

CMP600-30 Icemaker Dispenser Service Manual
© 2004-2014, Cornelius Inc. - 5 - Publication Number: 630460050SER
Figure 2. Schematic Diagram

CMP600-30 Icemaker Dispenser Service Manual
Publication Number: 630460050SER - 6 - © 2004-2014, Cornelius Inc.
ICEMAKER CLEANING AND SANITIZING PROCEDURES
CAUTION:
!
Do not use any of the ice made during cleaning operations.
Clean and sanitize ice storage area when cleaning icemaker.
1. Shut off water supply.
2. Remove ice from storage bin.
3. Mix approved cleaner (2 gallons as directed). Recommended cleaner: Calgon Corp. or Virginia Chemicals,
ice machine cleaner. Mixture: 3-1/3 ounces per gallon water. Do not use nickel safe cleaners.
4. Turn machine on and add cleaner solution to water level control (float reservoir) until 2 gallons have been used.
5. Turn on water supply and run machine for 15 minutes.
6. Turn off machine. Remove and discard all ice.
7. Sanitize using household liquid bleach (50 PPM chlorine). Mixture: 1 fluid ounce per gallon room temperature
water. 2 minute exposure time.
8. Sanitize pre-cleaned inside areas of storage bin liner, door frame, door, as well as exposed surfaces of the
evaporator assembly and bin shutoff assembly with sanitizing solution and allow to air dry.
MAINTENANCE
CAUTION:
!
Preventive Maintenance Can Increase The Trouble Free Life Of Your Ice Maker. Failure To Perform Preventive
Maintenance Could Void Your Equipment Warranty.
Many authorized Cornelius Service Agencies offer service contracts. Contact your local distributor for further
information.
Monthly
1. Clean the condenser. Use a brush, vacuum cleaner or blow from inside with air or CO2gas. If unit is provided
with an air filter, clean or replace.
2. Inspect water feed reservoir at least once a month until a definite pattern for cleaning and sanitizing has been
established.
Quarterly
This is the maximum period of time between cleaning and sanitizing the icemaker. In addition to recommended
monthly procedure, and if a more frequent cleaning and sanitizing pattern has not been established, unit must be
cleaned and sanitized quarterly.

CMP600-30 Icemaker Dispenser Service Manual
© 2004-2014, Cornelius Inc. - 7 - Publication Number: 630460050SER
Semi–Annually
1. Semi–Annually in addition to all previously established service procedures perform the following:
2. Check for water leaks; tube connections, water fillings and lower icemaker water seal.
3. Check drain tubes for clogs and “aged” tubes. Replace if tubes are stained or brittle.
4. Check for signs of condensation. Clean where necessary and replace insulation properly.
5. Check safety circuits for proper operation.
6. Check refrigeration system (see Page 9).
7. Check unit for abnormal noise. Tighten machine and cabinet screws, if necessary.
8. Check white upper bearings on auger assembly. If bearings are less than 1/16” thick, replace See Figure 3.
Figure 3. Auger Assembly

CMP600-30 Icemaker Dispenser Service Manual
Publication Number: 630460050SER - 8 - © 2004-2014, Cornelius Inc.
WATER LEVEL CONTROL
HOW WATER LEVEL CONTROL WORKS
When water is introduced through the inlet fitting the float rises, the float pushes against a lever that in turn, forces the
poppet assembly against the inlet fitting valve seat that seals the water off. See Figure 1. Before the water inlet is
sealed, the safety switch is operated. In the event of a water failure the float would drop down and operate the safety
switch to shut off the machine.
If water level control will not shut off and seal at level as indicated, be sure inlet pressure does not exceed
recommended factory operating range.
Under ordinary circumstances adjustment should not be necessary providing it was properly adjusted when unit was
installed or relocated. If however, the control becomes inoperative, repair or replace. See Start-up Adjustment page 7.
PURPOSE OF WATER LEVEL CONTROL
1. To automatically maintain proper water level in the evaporator when the unit is running and making ice.
2. A safety switch is operated in the event of an interruption in water supply. The switch shuts off the electrical
power to the icemaker and its refrigeration system. Switch will reset as soon as cause of water failure has been
corrected and proper water level in icemaker has again been reached.
3. The transparent bowl not only provides a visible check of water level, but also is a good guide to the internal
conditions which exist within the icemaker assembly itself. (See cleaning procedure.)
TOREPLACE WATER LEVEL CONTROL
!
WARNING:
Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all
power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
1. Shut off the water supply, unplug the ice dispenser from electrical outlet.
2. Remove the flexible tubing from bottom of water level control and drain water from water level control and evap-
orator.
3. Remove flexible tubing at bottom of water level bowl connected to the overflow.
4. Hold water inlet fitting with proper tool to prevent it from rotating when disconnecting the water inlet.
5. Remove wing nut holding water control to its mounting bracket. Control can be removed by lifting straight up.

CMP600-30 Icemaker Dispenser Service Manual
© 2004-2014, Cornelius Inc. - 9 - Publication Number: 630460050SER
TOREPLACE WATER LEVEL SAFETY SWITCH
!
WARNING:
Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all
power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
1. Unplug the ice dispenser from electrical outlet.
2. Unplug Molex connector connecting switch to electrical box.
3. Remove the 2 screws anchoring the water level safety switch to the bottom of the water level control mounting
bracket.
ICE LEVEL CONTROL
The ice level control assembly is secured to the top of the ice storage container cover. The cover is secured to the
storage container with four screws. The level control switch is operated by a plate assembly located beneath the
diaphragm. When the plate assembly is down due to lack of ice in storage container, electrical impulse is sent to
compressor, starting the ice making cycle. As ice level increases in storage container, the plate assembly is pushed
up. When storage container is full, it deactivate the switch, stopping the compressor and ice making cycle. The
operating positions of the switch is fixed, no adjustments are necessary. If switch replacement becomes necessary,
simply disconnect cable at connector, remove wires from switch.

CMP600-30 Icemaker Dispenser Service Manual
Publication Number: 630460050SER - 10 - © 2004-2014, Cornelius Inc.
REFRIGERATION SYSTEMS
REFRIGERATION SYSTEM ADJUSTMENTS
A complete understanding of the icemaker and hermetic refrigeration system is necessary before any adjustments
are made. The refrigeration technician must use high and low side pressure readings, water and air temperatures,
plus general conditions of cleanliness to assess the refrigeration system status when making any adjustments.
All icemaker products are tested and adjusted at the factory prior to shipment where the ambient temperature ranges
from 65°F to 90°F, depending on the season of the year.
Whenever a new icemaker is initially installed and started–up, it is imperative that the start–up operator make the
following checks and readjustments for local conditions.
EXPANSION VALVE
You will find a thermal expansion valve on Wilshire ice makers, which is used to control the amount of refrigerant
flowing through the evaporator. Improperly installed or defective expansion valves may cause low production, soft ice,
squeaking from evaporator and excessive load inside evaporator.
By using general refrigeration trouble shooting along with the pressure charts, you can easily determine whether or
not the expansion valve is working properly.
ADJUSTMENT AND TROUBLESHOOTING
When troubleshooting the expansion valve, you must;
1. Be sure you have adequate water flowing into the evaporator, a clean and properly ventilated condenser, and
the system is properly charged and free of any restrictions. Also be sure compressor is operating properly.
2. Take reservoir water temperature and air temperature from condenser inlet and determine at what pressure
unit should be running. On machines equipped with thermostatic valve there is NO adjustment. If correct pres-
sure cannot be obtained, be sure system has time to stabilize, 10–15 minutes.
3. Be sure sensing bulb is located at outlet side of evaporator about 3–4 inches away from evaporator and be sure
to insulate well and clamp tightly to tubing. If system pressures are still not adequate, take a second water and
air temperature reading and go over other parts of the system for possible problems. If proper charge is ques-
tionable evacuate and recharge to nameplate and leak check. If valve still malfunctions replace valve.
Use general refrigeration system practices when replacing and recharging unit. After new valve is in place, go
through previous monitored adjustments and troubleshooting to be sure valve is functioning properly.
NOTE: On water cooled units adjust condenser modulating valve before troubleshooting expan-
sion valve.
CAUTION:
!
Very high discharge pressure is present in system. Quick disconnects on your gages will minimize Danger and loss of
refrigerant. Comply with federal regulations for reclaiming refrigerant.

CMP600-30 Icemaker Dispenser Service Manual
© 2004-2014, Cornelius Inc. - 11 - Publication Number: 630460050SER
TEMPERATURE/PRESSURE CHARTS*
Refrigerant
Type R404A
CMP 600-30
±10 lb. Discharge Pressure
Water Temperature(° F)
40 65 90
Air Temperature (°F)
50 174 177 180
60 202 205 208
70 230 233 236
80 265 269 272
90 300 304 307
100 328 334 340
NOTE: *The thermostatic expansion valve is non–adjustable on all models
CONDENSER MODULATING VALVE
The reason for using a water modulating valve is to supply the correct amount of water to the condenser to maintain
the proper operating pressure in the refrigeration system high side. The flow of water through the valve is increased
as the high side pressure rises and decreases as high side pressure lowers.
Figure 4. Adjustment Screw
To calibrate the amount of water flow with the refrigeration system high side pressure, turn adjustment screw located
on end of valve opposite of bellows See Figure 4. Turn screw counterclockwise to raise opening point. Opening point
of valve should be set to maintain proper operating pressure in refrigeration system high side. Refer to Pressure Chart
on Page 10. Closing point of valve should be set low enough to close valve during compressor stand by periods.
NOTE: Cold water will absorb more heat faster than warm water. The water flow will therefore auto-
matically increase as inlet temperature increases.

CMP600-30 Icemaker Dispenser Service Manual
Publication Number: 630460050SER - 12 - © 2004-2014, Cornelius Inc.
CONDENSER MODULATING VALVE REMOVAL
!
WARNING:
Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all
power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
1. Shut off water supply to condenser and reclaim refrigerant from system.
2. Remove inlet water line from Condenser modulating Valve. Also remove tube from refrigerant high side line.
3. Remove Condenser Modulating Valve and bracket from unit.
4. Remove valve from bracket.
5. Replace Condenser Modulating Valve by reversing Steps 2 thru 4. Then pull system into vacuum.
6. Recharge unit with refrigerant per nameplate.
7. Turn power and water ON to unit.
8. With unit running adjust modulating valve to proper setting.
9. Go through a complete system check.
GEAR MOTOR
The gear motor is equipped with a start relay and a manual reset overload. When current is applied, the relay
energizes and completes the circuit to the start winding. The motor reaches a predetermined speed and the relay
drops out, disconnecting the start winding. The run winding remains in the circuit as long as current is applied.
The purpose of the overload is to automatically shut off the motor in the event of a mechanical bind of the
transmission, an overload condition within the evaporator or an electrical malfunction. It does this by sensing
amperage draw. If the motor stalls the start relay would energize and stay energized. The amperage would surge to 5
to 6 times greater than normal draw. In this event the overload would shut off the transmission in 4 to 8 seconds.
If the motor is subjected to an abnormal load, but does not reach stall condition, the overload will react, but over a
greater period of time. The reaction time depends upon the amperage to which it is subjected.
The overload, through the safety circuit, also shuts off the compressor.
Refer to Troubleshooting Guide.

CMP600-30 Icemaker Dispenser Service Manual
© 2004-2014, Cornelius Inc. - 13 - Publication Number: 630460050SER
TROUBLESHOOTING
!
WARNING:
Only trained and certified electrical, plumbing and refrigeration technicians should service this unit.
All wiring and plumbing must conform to national and local codes. Failure to comply could
result in serious injury, death or equipment damage.
TROUBLESHOOTING GEAR MOTORS
Basically, Gear motor problems can be narrowed down to three areas of checkout.
The Gear motor will not run
1. No voltage to the transmission terminals – check external circuit.
2. Low voltage – check supply.
3. Problems in the gear motor electrical circuit. See Figure 5.
The Gear motor Starts buts Trips Repeatedly on the Overload Protector:
1. Voltage – high or low voltage can cause the overload to trip.
2. High Gear motor amperage draw, see Specification Chart for ratings and Troubleshooting Guide.
Figure 5. Output Shaft
The Motor Runs but Output Shaft does not Rotate:
Replace defective gear motor.
!
WARNING:
Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all
power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
OVERLOAD CHECK:
1. Allow motor to cool and reset overload if necessary.
2. Remove motor end bell and stator, if necessary.
3. Check terminals 1 and 3 on overload. No continuity replace overload. Use a volt–ohm meter. See Figure 5 and
Figure 6.

CMP600-30 Icemaker Dispenser Service Manual
Publication Number: 630460050SER - 14 - © 2004-2014, Cornelius Inc.
MOTOR CHECK:
The resistance readings on the windings will be between 5 to 25 ohms. A meter capable of these low readings must
be used. The Start Relay cover must be removed. NOTE: Gear motor and related components can be checked from
Pin Connector. See Figure 5 and Figure 6.
If no continuity on start or run winding test, replace stator. If continuity on grounded motor test, replace stator.
INSTALLATION AND SHAFT SEAL REPLACEMENT
1. Place shaft seal locator seat over gear motor output shaft, embossed side down, and push down until shaft
seal seat rests flush on top of gear motor.
2. Place rubber coated ceramic seal (important: ceramic face up) over output shaft and push down until seal rests
on top of the shaft seal seat. (Lubricate rubber on ceramic seal with [#06195] rubber lubricant.)
3. Place shaft seal with carbon face down (spring up) over output shaft and push (gently) downward until seal
rests on carbon face of the output shaft seal.
4. Push down on the washer compressing the spring on the output shaft seal. While holding the seals (down) in
place slide the E–ring into the groove on the output shaft.
AUGER & EXTRUDING HEAD REMOVAL
Figure 6. Shaft Seal Replacement Figure 7. Extruding Head Figure 8. Auger
(See Figure 6)

CMP600-30 Icemaker Dispenser Service Manual
© 2004-2014, Cornelius Inc. - 15 - Publication Number: 630460050SER
AUGER & EXTRUDING HEAD REMOVAL
Figure 9. Upper Nut and Bearing
The upper bearings located on top of the auger is used to absorb the force between the auger and extruding head.
The bearings are 3/32” thick. When they wear below 1/16” they should be replaced. Bearings to be inspected for wear
during quarterly maintenance. See Figure 9.
TOREPLACE BEARINGS
!
WARNING:
Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all
power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
1. Dispense all ice from unit.
2. Remove panels.
3. Unplug Dispense Motor and Ice Level Switch.
4. Remove four screws holding dispense cover in place.
5. Remove dispense cover assembly.
6. Use an open end wrench on auger nut connected to bearing and turn and turn counterclockwise to remove
assembly.
7. Remove worn bearings. Replace with new bearings and then reinstall assembly. NOTE: If auger turns with nut,
remove cover on top of gear motor stator and hold rotor while loosening nut.
8. Reconnect power to icemaker.
TROUBLESHOOTING COMPRESSOR
Basically the compressor problems can be narrowed down to three areas of checkout
1. THE COMPRESSOR WILL NOT RUN:
A. No voltage to the compressor terminals – check circuit.
B. Low voltage – below 90% of nameplate rated voltage.
C. Problems in the compressor electrical circuit. See Electrical Checkout instructions.
2. THE COMPRESSOR STARTS BUT TRIPS REPEATEDLY ON THE OVERLOAD PROTECTOR:
A. Check for proper fan operation and clean condenser.
B. Check the compressor suction and discharge pressures.
C. Voltage – The voltage should be within 10% of the rated nameplate voltage.
D. High compressor amperage draw, it should never exceed 120% of the rated nameplate amperage. See
Electrical Checkout Instructions.

CMP600-30 Icemaker Dispenser Service Manual
Publication Number: 630460050SER - 16 - © 2004-2014, Cornelius Inc.
3. THE COMPRESSOR RUNS BUT WILL NOT REFRIGERATE:
Check the compressor suction and discharge pressures. See Chart on Page 10.
ELECTRICAL CHECKOUT
Figure 10. Electrical Box
!
WARNING:
Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all
power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
1. Be sure the unit is disconnected from the power source. Remove the compressor electrical box cover. Check
for obvious damage and loose wires.
2. Disconnect the fan motor leads. Since capacitors store energy, short the capacitor with a screwdriver. This will
prevent shocks.
3. Disconnect the compressor terminal wires.
OVERLOAD CHECK
Using a volt–ohm meter check the continuity across the overload, contacts #1 & #3. If none, wait for unit to cool down
and try again. If still no continuity, the overload protector is defective and should be replaced.
COMPRESSOR CHECK
The resistance readings on the windings will be between 0.25 and 10.00 ohms, a meter capable of these low readings
must be used.-
1. Check between “C” & “R.” Replace compressor if there is no continuity as the run windings are open.
2. Check between “C” & “S.” Replace the compressor if there is no continuity as the start windings are open.
3. Check between “C” & “R”, or “S” and shell of the compressor. If there is continuity replace the compressor as
the motor is grounded.
4. Check between screw terminal on the overload and “C” on the compressor. Check and repair the lead or con-
nections if there is no continuity.
CAPACITOR CHECK
1. Check or replace start capacitor, disconnect bleed resistor before checking for shorted capacitor.
2. Check or replace run capacitor (if supplied) check or shorted capacitor or either terminal grounded to case.
(See Figure 5)
(See Figure 10)