Cornell CTP-E50T User manual

CTP-E50T
THERMO POT
USER MANUAL

6. Cover release button
7. Handle
8. Power cord
9. Filter
10. Power socket5. Steam vent
4. Body
3. Water outlet
2. Control panel
1. Lid latch
1. Reboil button
2. Temperature setting button
3. Water dispense button
4. Unlock / lock button
5. Turn on / off button
PART NAME SAFETY INSTRUCTION
CONTROL PANEL
1
2
3
5
49
8
7
6
1. Avoid contact with steam outlet from steam vent;
or when the lid is lifted or pouring out hot water.
2. Always unplug unit from the power outlet when not in use.
Unplug and wait unit cool before cleaning.
5. Never overfill-boiling water may splash out, and cause burn(water
full indicator is the highest capacity). Always make sure that the lid is
clipped in place during use.
Warning: do not open the lid while water is boiling
4. Always use the unit on a flat, stable and heat resistance surface.
6. Never immerse the unit or base in water other liquids.
7. Always keep the unit away from the cookers, hotplates or stoves.
8. Keep hands clear of the water outlet during serve in case scald.
9. This unit is for boiling water only.
10. With any indication of malfunction, or power cord and plug is
damaged, stop to use immediately. Do not try to repair by yourself.
Take it to authorized maintenance center to repair.
11. Keep small children away from the unit and do not let the power
cord hand down over the worktop edge child could grab it and pull
the unit down.
3. Take extreme care when moving the unit if it contains hot water.
1
2
4
3
5
TEMP.
SETTING
POWER
ON / OFF
UNLOCK
CHLORINE
PURIFYING
REBOIL
Boiling
Keep
warm
DISPENSE
FULL

OPERATION INSTRUCTION
CARE AND CLEANING
Before cleaning: disconnect from the power and allow to cool, remove
lid and empty any water.
Wipe with a damp cloth and mild detergent then wipe dry with a soft
cloth. Never use any chemical, steel wool or abrasive cleaners to clean
the exterior of the unit. It will damage the surface.
Clean regularly with a sponge or damp cloth.
Dry with a soft cloth.
The interior can become discolured because of deposits of limescale
and particles after porlonged use. This is not harmful to health, but
may be cleaned as follows:
1. Fill with water, adding 30g of citric acid or some lemon slices.
2. Start boiling water and then keep water warm at 85oC for 3-4 hours.
3. Then empty the unit, normally the limescale will all gone.
4. Before back to normal use the unit, it’s recommend to fill the unit
then boil and emptied again to wipe of the acid smell/taste.
TO CLEAN THE EXTERIOR
TO CLEAN THE INTERIOR
OVER-HEATING PROTECTION
If unit start boiling without fill in water(dry-boil), the temperature
inside will go up untill trigger the over-heating protection.
In this condition, the unit will shut down automatically, alll indicator
lamp will turn off. To make the unit back to normal status,
fill in cold water and wait till the “Boilling”lamp back to flash.
Remove all package and labels before using the unit
BOILING WATER
1. Press “Keep warm setting” to select demand keep warm temp.
SETTING KEEP WARM TEMPERATURE
2. The temp. lamp will keep flashing till the water reach demand
temp and then stay on.
1. Open the lid and fill water till the full mark.
2. Close the lid tightly and plug in the power cord to wall power.
3. “Boiling”lamp will flash indicate it’s in the standby mode.
4. Press the “Power on/off” button to start boiling.
5. “Boiling”lamp will stay on indicate the boiling is process.
6. When the boiling is finish, “Keep warm” lamp will stay on.
After finish boiling,press the“Power on/off” button to activate the
standby mode to allow water cool down naturally to room temp.
In the standby mode,the “boiling” lamp will stay in flash.
The default keep warm temp.is 55oC.
*
*
*
WATER DISPENSE
The water dispense function is workable in standby mode.
*
1. Press “Unlock”button to unlock the unit.
2. Press “Dispense”button to obtain water.
UNLOCK POWER
ON/OFF

TROUBLESHOOTING
SPECIFICATION
CTP-E50T
220-240V~ 50/60Hz
750-892W
5.0 Litre
Voltage
Model No.
Power
Capacity
No power
Water flowing out
from unit
White residues in
the water
Boiling sound is
excessively loud
Water overfill
Mineral deposit (not
a defect of unit)
Interior get too many
limescale
Clean the unit
according care and
cleaning section.
Clean the unit
according care and
cleaning section.
Do not fill water over
the FULL line
Power cord do not plug
in wall power very well
or body do not stand on
the base completely.
Check connection of
power cord.
Check connection
between body and base.
PROBLEM CAUSE SOLUTION