Corriveau ErL3003X User manual

S $esters hanrmnck ïawn eïYin{t
IJ,tJith *uähionä
ErL3003><-

Warning
1. lt is the consumer's responsibility to comply with any building codes, ordinances, zoning
limitations, or local homeowner's restrictions and obtain any required permit, before purchase and
installation of the products.
2. Two persons are required for assembly. Required tools includes an Allen Wrench (part KK in
hardware pack) and other safety items, such as gloves, protective goggles and hardhat. To avoid
any injury from exposed sharp edges, it may be necessary to use above safety equipments.
3. This unit will take about 2 hours to set up. You must schedule enough time to complete the
assembly so you don't leave it unattended if not fully assembled, even if bolted to the ground.
. Make sure that all components are in the box. Read instructions carefully before starting the
assembly,
. Follow all instructions to assure the strength of the lawn swing.
. ln order to avoid damage to the lawn swing use appropriate tools.
. Check all screws on a regular basis to maintain the solidity of the structure.
. Keep instructions and parts list for future use.
Care tnstructions
. Use soap or mild detergent and wash in warm water using a cloth or sponge. Rinse with water
and allow it to dry in open air. Do not use strong cleansers.
. We strongly recommend that you store your product in a warm temperature place during winter.
. We also recommend removing the excess of water that may have entered the pipes, because
frozen water may crack your frame during winter.
Åttentüosl
. We recommend to store your cushions in a dry place after each use away from direct sunlight or
rain.
. ln periods of high winds, remove the canopy.

oP
@
AL@
u
6L
ùJD
JK
c
B
E
F
S

PAruTS L-ISî:
Drawing
Description
Top Frame Bar
Rear Leg
1
Left Front Leg
1
Right Front Leg
Leg Support
Leg Crossbar
Rear Crossbar
1Back
Short Bar
Hook
Canopy Slide Bar
1
Canopy Edge Left Bar
1
Knob
1Canopy

No. Description Qty" Drawing
RCushion 3I\
%
SPillow 2
Hardware Kit:
Drawing
Description
Item
MOX3SLBolt
M6XSSLBolt
M6X90LBolt
MSX3SLBolt
MSX90LBolt
M6 Nut
Hitch Pin
Plastic Washer
Metal Washer
1
Allen Wrench
pen-en renc
1
MB Open-end Wrench

X:I
x1
\.2-
A
B
c
D
X1
A
I,IIIt.
ì
t
I
t
¡.
I
t
I
I
t.
¿
t
Ø
o
:mù!.-
t,
mØ*,
@
CC
.(kt
@
-@-
JJ
@
JJ
@s.l
A
o
t
üI
1
'Itt
I
I
i
¡
i
a
t
JJ
B
-@-
JJ
-@_@
t
t
t
,¡
.¡
I
¡
r{It!
!
D
¡
j ffi-ør
jrrJ¡
t
rt,!
B
@
JJ
JJ
@-
@
FF
I
:\
C
t
B
0
4
!
Step 1
:
MetalWashers (JJ), Left Front Leg (C), Rear Leg (B)and Metal Washers (JJ), and tighten with M6 Nuts
(FF) as figure (2)shown.
2. Repeat on the opposíte side for Right Front Leg (D).
5

x2
x2
x1
E
F
G
JJ
B
FÉ B
fn
JJ JJ
c
G
F
e,
1
D
B
E@
EF
Øi
o*S*
Jì
i
,
bJJ
-å-
w
AA -%"
AA
E. ',68
.FFJ
JJ Þ
Step 2:
1. lnsert M6 X 90 Bolt (CC) through Metal Washer (JJ), Rear Leg (B), Rear Crossbar (G) and Metal
Washer (JJ), and secure with M6 Nut (FF) as figure (1) shown, hold in position. Then insert M6 X 90 Bolt
(CC) through Metal Washer (JJ), Leg Crossbar (F), Rear Leg (B), Rear Crossbar (G) and Metal Washer
(JJ), and secure with M6 Nut (FF) as figure (1) shown. Do not tighten the bolts yet.
2. lnsert M6 X 55 Bolt (BB)through Metal Washer (JJ), Leg Crossbar (F), Front Leg (D), Leg Support (E)
and MetalWasher and secure with M6 Nut FF AS re shown. Do hten the bolts
3. lnsert M6 X 35 Bolts (AA) through Metal Washers (JJ)and Leg Support (E), then secure with Rear
Crossbar (G) as figure (3) shown.Do not tighten the bolts yet.
4. Repeat above procedures on the opposite side. When all is set in place, please tighten all bolts now
6
i
:

X1
X1
H
I
fl)
rli
Step 3:
ffiff" EB
JJ;
t\
t\ \!
¡.
I
l
I
tI
I
ll@
FF
Hru
---**-*r
Seat HPlastic Washer Back Plastic
Washer (ll), Seat (H) and Metal Washer (JJ), secure with M6 Nut (FF) as figure shown. Make sure two
ptastic Washers (ll) are in between Back (l) and Seat (H) once installed. Repeat for the opposite side.
Notes: Please check above fig. carefully and make sure all the parts in right position. For the sake of
safety, you may need 2 people for this step'
7I

J2
Xx2
HH
Kxå -ffikl¡H
åå
J
¡r{'úr¡*
t
Ji
t
I
I
I
J{I
aIti
¡K
I
I
f
¿
K
"tr
H-
I
EE
r%i"å æ
B
K
J
K
H
JJ JJ
J
H
Step 4:
I
ÆGG
\*d" _9F-g
1. Secure Arm (J) on the Seat (H) by using M8 X 90 Bolts (EE), Metal washers (JJ) and M8 Nut (GG) as
figure (1) shown, Repeat on the opposite side.
Notes: For the sake of uneed 2e for this step.
1
0
2. lnsert M6 X 55 Bolts (BB)through Plastic Washers (ll), Short Bar (K), Plastic Washers (ll) and secure
with Back (l), and tighten with MetalWashers (JJ) and M6 Nuts (FF), Then insert Hitch Pin (HH)through
Shcrt Bar (K) and Arm (J), Secure loop at the end of Hitch Pin (HH) as figure (2) shown.Repeat on the
opposite side.
Notes: Please check above fig. carefully and make sure all the parts in right position.
8

Lx2
Notes: You may need 2 people for this step
o
A\
t
!
J:
-J*
(1)
,
I
I
!
t:
t,
tL
¡. tq
,ry
I lt IA
Step 5:

2
X
X1
X1
M
N
o
o
M
NM
!
NM
,ffi
iI
o
Step 6: [eft and
M
Ëlars &

2
X
P
DD iu
wry
F\
I
f.
t
tI
coffi
Step 7:
Secu re-Ca n opy Ba r-Asse m bly-on-the-Left-Er:ont Leg (C) by,using
D
Plastic
N
- ""* *G
Edge Left Bar (N) and Plastic washer (ll), secure on Left Front Leg (C)'
Repeat the procedure on the opposite side.
Note : you can change tilt of the Canopy assembly by adjusting the Knobs (P). Then securely tighten'
For the sake of safety, you may need 2 people for this step.
11
n
a

x1
,0
w, O
1M
N
ep
Place the Canopy (Q) on the Canopy bâr assembly, secure with hooks and loop straps
12

3S
RXx2
Make sure legs and ground are perpendicular with each other once the unit is assembled. Tighten all
bolts evenly, Place the Cushion (R) and Pillow (S) on the seat. Enjoy your leisure time with Casual
Swing.
13