Corsair H100i User manual

iCUE
H100i | H115i | H150i
ELITE
PERFORMANCE LIQUID CPU COOLER
ENGLISH
EN
FRANÇAIS (EURO)FR
DEUTSCH
DE
NEDERLANDS
NL
ITALIANO
IT
ESPAÑOL (EURO)
ES
PORTUGUÊS (EURO)
PT
POLSKI
PL
PУССКИЙ
RU 简体中文SC

AR

ENGLISH
TABLE OF CONTENTS
Note: Most newer PC cases include a CPU cut-out to allow access to the bottom of the motherboard.
If your case does not include a cut-out, you will need to remove your motherboard from the case prior
to installation. ELITE Series coolers come with the Intel mounting bracket pre-installed on the pump for
quick installation.
INTEL
AMD AM4
AMD sTRX4
FINISHING UP YOUR INSTALLATION
FAQ


ENGLISH
ENGLISH INTEL

ENGLISH
ENGLISH INTEL
SATA POWER
B CA
D E F
G
H
I
LK
J
N OM
X4 INTEL 1200/1156/1155/1151/1150
STANDOFFS
X4 INTEL 2066/2011-3/2011 STANDOFFS X4 INTEL 1700 STANDOFFS
X1 INTEL BACKPLATE
(1200/115X/1700 ONLY)
X1 INTEL MOUNTING BRACKET
(PRE-INSTALLED)
X4 THUMB NUTS
X4 AMD AM4 STANDOFFS X1 AMD AM4 MOUNTING BRACKET X1 AMD STR4/STRX4
MOUNTING BRACKET
X4 AMD STR4/STRX4 STANDOFFS X16 LONG FAN SCREWS (H100i/H115i)
X24 LONG FAN SCREWS (H150i)
X8 RADIATOR SCREWS (H100i/H115i)
X12 RADIATOR SCREWS (H150i)
X16 WASHERS (H100i/H115i)
X24 WASHERS (H150i)
X2 AF ELITE FANS (H100i/H115i)
X3 AF ELITE FANS (H150i)
X1 USB-C WIRE HARNESS
Highlighted parts for Intel installation only
INCLUDED HARDWARE

ENGLISH
ENGLISH

D
CLGA 1700
BLGA 2011/
2011-3/2066
ALGA 1200/1150/
1151/1155/1156
> Attach the provided Intel standoff for
your socket.
> Use (A) for LGA 1200/115X, (B) for
LGA 2011/ 2011-3/2066 or (C) for
LGA1700.
> Tightenallfourstandoffsuntilrmly 
secured.
Adjust backplate for your required socket.
NOTE: Intel LGA 2066 /2011-3/2011
do not require backplate installation.
Proceed to step 2.
2. INSTALLING THE INTEL STANDOFF SCREWS
1. INSTALLING THE INTEL BACKPLATE

ENGLISH
ENGLISH
Please continue to Page 10 to continue your installation.

K
N
M
LAttach the radiator and the fans as shown.
For the best cooling performance, we
recommend mounting the fans as an
air-intake to your PC case.
> Align the bracket and pump over the
standoff screws as shown.
> Attach the thumb nuts (F) to the standoff
screws as shown.
> Tighten the thumb nuts until all four corners
 arermlysecured.
4. INSTALLING THE PUMP UNIT
3. INSTALL THE FANS AND RADIATOR

ENGLISH
ENGLISH AMD AM4

SATA POWER
B
C
A
D
E
F
G H
I
LK
J
N OM
X4 INTEL 1200/1156/1155/1151/1150
STANDOFFS
X4 INTEL 2066/2011-3/2011 STANDOFFS X4 INTEL 1700 STANDOFFS
X1 INTEL BACKPLATE
(1200/115X/1700 ONLY)
X1 INTEL MOUNTING BRACKET
(PRE-INSTALLED)
X4 THUMB NUTS
X4 AMD AM4 STANDOFFS X1 AMD AM4 MOUNTING BRACKET X1 AMD STR4/STRX4
MOUNTING BRACKET
X4 AMD STR4/STRX4 STANDOFFS X16 LONG FAN SCREWS (H100i/H115i)
X24 LONG FAN SCREWS (H150i)
X8 RADIATOR SCREWS (H100i/H115i)
X12 RADIATOR SCREWS (H150i)
X16 WASHERS (H100i/H115i)
X24 WASHERS (H150i)
X2 AF ELITE FANS (H100i/H115i)
X3 AF ELITE FANS (H150i)
X1 USB-C WIRE HARNESS
Highlighted parts for AMD AM4 installation only
INCLUDED HARDWARE

ENGLISH
ENGLISH

E H
Figure 1 Figure 2
K
N
M
L
> Remove the integrated Intel mounting
bracket (Figure 1).
> Install the AMD AM4 bracket by pushing
both sides into the slot on the pump until
secure (Figure 2).
Note: It is important that the AMD AM4
retention bracket be evenly secured on
all sides before installation.
Attach the radiator and the fans as shown.
For the best cooling performance, we
recommend mounting the fans as an
air-intake to your PC case.
2. INSTALL THE FANS AND RADIATOR
Remove the existing AMD AM4 mounting
brackets shown.
3. PREPARE THE MOTHERBOARD FOR INSTALLATION
1. INSTALLING THE AMD AM4 MOUNTING BRACKET

ENGLISH
ENGLISH

G
Please continue to Page 10 to continue your installation.
Align the bracket with the AMD AM4
standoffs as shown. Tighten the thumb
nuts (F) until secure.
> Attach the provided AMD AM4 standoffs
to the CPU socket.
> Tightenallfourscrewsuntilrmlysecure.
5. INSTALLING THE PUMP UNIT
4. INSTALLING THE AMD AM4 STANDOFF SCREWS

ENGLISH
ENGLISH AMD sTRX4

SATA POWER
B
C
A
D
E
F
G
H
I
LKJ
N OM
X4 INTEL 1200/1156/1155/1151/1150
STANDOFFS
X4 INTEL 2066/2011-3/2011 STANDOFFS X4 INTEL 1700 STANDOFFS
X1 INTEL BACKPLATE
(1200/115X/1700 ONLY)
X1 INTEL MOUNTING BRACKET
(PRE-INSTALLED)
X4 THUMB NUTS
X4 AMD AM4 STANDOFFS X1 AMD AM4 MOUNTING BRACKET X1 AMD sTR4/sTRX4
MOUNTING BRACKET
X4 AMD sTR4/sTRX4 STANDOFFS X16 LONG FAN SCREWS (H100i/H115i)
X24 LONG FAN SCREWS (H150i)
X8 RADIATOR SCREWS (H100i/H115i)
X12 RADIATOR SCREWS (H150i)
X16 WASHERS (H100i/H115i)
X24 WASHERS (H150i)
X2 AF ELITE FANS (H100i/H115i)
X3 AF ELITE FANS (H150i)
X1 USB-C WIRE HARNESS
Highlighted parts for AMD sTRX4 installation only
INCLUDED HARDWARE

ENGLISH
ENGLISH

J
I
Figure 1 Figure 2
E
> Attach the provided AMD sTRX4 standoffs
to the CPU socket.
> Tightenallfourstandoffscrewsuntilrmly
secure.
> Remove the integrated Intel mounting
bracket (Figure 1).
> Install the AMD sTRX4 bracket by pushing
both sides into the slot on the pump until
secure (Figure 2).
Note: It is important that the AMD sTRX4
retention bracket be evenly secured on all
sides before installation.
2. INSTALLING THE AMD sTRX4 STANDOFF SCREWS
1. INSTALLING THE AMD sTRX4 MOUNTING BRACKET

ENGLISH
ENGLISH

K
N
L
M
Please continue to Page 10 to continue your installation.
> Align the bracket and pump over the
standoff screws as shown.
> Attach the thumb nuts (F) to the standoff
screws as shown.
> Tighten the thumb nuts until all four corners
 arermlysecured.
Attach the radiator and the fans as shown.
For the best cooling performance,
we recommend mounting the fans as
an air-intake to your PC case.
4. INSTALLING THE PUMP UNIT
3. INSTALL THE FANS AND RADIATOR

ENGLISH
ENGLISH

Figure 1 Figure 2
3-PIN
> Using the included USB-C cable, connect the iCUE ELITE Series cooler to a motherboard
USB 2.0 header.
> Connect pump power cable that is attached to the USB-C Wire Harness to an available SATA power
plug from your power supply.
> Connect pump tach cable to the CPU_FAN header on your motherboard (Figure 1).
> Connect each fan to the USB-C Wire Harness and connect the USB-C cable to the pump (Figure 2).
CONNECT PUMP TO USB AND SATA POWER
CONNECT FANS TO PUMP AND PUMP TO MOTHERBOARD

ENGLISH
ENGLISH

FAQ
1.HowdoIknowthedirectionoftheairowofthefan?
 Anarrowlocatedonthesideofthefanindicatesthedirectionofairow.
2.CanIreusethepre-appliedthermalpasteonthecoolerforre-installation?
Re-installation of the cooler will require you to clean off the pre-applied thermal paste and apply
an aftermarket paste.
3.WhatorientationshouldIinstallmyradiator?
The best way to install a radiator is with the tubes on the bottom of the case, though you can install it
with the tubes in any position, including an inverted radiator, as long as the highest point in the radiator
is visibly higher than the CPU pump.
4.Mycoolerandfansareblinkingredornotfunctioning.WhatdoIdo?
Please double check all connections between the cooler and fans. Ensure that the cooler is updated
 tothemostrecentrmwareviaiCUE.Ifthisdoesnotresolveyourproblems,pleaseopenasupport
ticket at support.corsair.com or contact our customer support team for further troubleshooting and
assistance.
https://help.corsair.com/hc/en-us/requests/new

FRANÇAIS
TABLE DES MATIÈRES
Remarque: La plupart des nouveaux boîtiers de PC comportent un accès facilité au processeur qui
permet d’accéder à la base de la carte mère. Si aucun accès n’est prévu sur votre boîtier, vous devrez
retirer votre carte mère du boîtier avant de procéder à l’installation. Les refroidisseurs ELITE Series sont
fournisaveclesupportdexationIntelpréinstallésurlapompeandepermettreuneinstallationrapide.
INTEL
AMD AM4
AMD sTRX4
ACHÈVEMENT DE VOTRE INSTALLATION
FOIRE AUX QUESTIONS


ENGLISH
ENGLISH INTEL

FRANÇAIS
FRANÇAIS INTEL
SATA POWER
B CA
D E F
G
H
I
LK
J
N OM
X4 ENTRETOISES INTEL
1200/1156/1155/1151/1150
X4 ENTRETOISES
INTEL 2066/2011-3/2011
X4 ENTRETOISES INTEL 1700
X1 PLAQUE ARRIÈRE INTEL
(1200/115X/1700 UNIQUEMENT)
X1 SUPPORT DE FIXATION INTEL
(PRÉINSTALLÉ)
X4 ÉCROUS À SERRAGE À MAIN
X4 ENTRETOISES AMD AM4 X1 SUPPORT DE FIXATION AMD AM4 X1 SUPPORT DE FIXATION
AMD sTR4/sTRX4
X4 ENTRETOISES AMD sTR4/sTRX4
X16 VIS DE VENTILATEUR LONGUES
(H100i/H115i)
X24 VIS DE VENTILATEUR LONGUES
(H150i)
X8 VIS DE RADIATEUR (H100i/H115i)
X12 VIS DE RADIATEUR (H150i)
X16 RONDELLES (H100i/H115i)
X24 RONDELLES (H150i)
X2 VENTILATEURS AF ELITE (H100i/H115i)
X3 VENTILATEURS AF ELITE (H150i)
X1 FAISCEAU DE CÂBLAGE USB-C
Les sections en surbrillance concernent uniquement l’installation Intel
MATÉRIEL INCLUS

FRANÇAIS
FRANÇAIS

D
CLGA 1700
BLGA 2011/
2011-3/2066
ALGA 1200/1150/
1151/1155/1156
> Attachez les entretoises Intel fournies pour
votre prise.
> Utilisez (A) pour le modèle LGA 1200/115X,
(B) pour LGA 2011/2011-3/2066 ou (C) pour
LGA 1700.
> Serrez les quatre entretoises jusqu’à
 cequ’ellessoientsolidementxées.
2. INSTALLATION DES VIS D’ENTRETOISE INTEL
Ajustez la plaque arrière pour votre socket.
REMARQUE: LGA 2066/2011-3/2011 ne
nécessitent pas l’installation d’une plaque
arrière. Passez à l’étape 2.
1. INSTALLATION DE LA PLAQUE ARRIÈRE INTEL

FRANÇAIS
FRANÇAIS
Veuillez passer à la page 10 pour procéder à la suite de l’installation.

K
N
M
LAttachez le radiateur et les ventilateurs,
comme illustré. Pour des performances
de refroidissement optimales, nous vous
recommandons d’installer les ventilateurs
comme une entrée d’air sur la tour de votre
ordinateur.
> Alignez le support et la pompe avec les vis
à entretoise comme indiqué.
> Attachez les écrous à serrage à main (F)
sur les vis à entretoise comme indiqué.
> Serrez les écrous à serrage à main jusqu’à
ce que les quatre coins soient solidement
 xés.
4. INSTALLATION DE LA POMPE
3. INSTALLATION DES VENTILATEURS ET DU RADIATEUR

AMD AM4
FRANÇAIS
FRANÇAIS

SATA POWER
B
C
A
D
E
F
G H
I
LK
J
N OM
Les sections en surbrillance concernent uniquement l’installation AMD AM4
MATÉRIEL INCLUS
X4 ENTRETOISES INTEL
1200/1156/1155/1151/1150
X4 ENTRETOISES
INTEL 2066/2011-3/2011
X4 ENTRETOISES INTEL 1700
X1 PLAQUE ARRIÈRE INTEL
(1200/115X/1700 UNIQUEMENT)
X1 SUPPORT DE FIXATION INTEL
(PRÉINSTALLÉ)
X4 ÉCROUS À SERRAGE À MAIN
X4 ENTRETOISES AMD AM4 X1 SUPPORT DE FIXATION AMD AM4 X1 SUPPORT DE FIXATION
AMD sTR4/sTRX4
X4 ENTRETOISES AMD sTR4/sTRX4
X16 VIS DE VENTILATEUR LONGUES
(H100i/H115i)
X24 VIS DE VENTILATEUR LONGUES
(H150i)
X8 VIS DE RADIATEUR (H100i/H115i)
X12 VIS DE RADIATEUR (H150i)
X16 RONDELLES (H100i/H115i)
X24 RONDELLES (H150i)
X2 VENTILATEURS AF ELITE (H100i/H115i)
X3 VENTILATEURS AF ELITE (H150i)
X1 FAISCEAU DE CÂBLAGE USB-C

FRANÇAIS
FRANÇAIS

E H
Figure 1 Figure 2
K
N
M
L
> PourretirerlesupportdexationIntel 
intégré (Figure 1).
> Installez le support AMD AM4 en appuyant
des deux côtés dans le logement sur la
pompe jusqu’à ce qu’il soit en place
(Figure 2).
Remarque: Il est important que le support
de retenue AMD AM4 soit bien en place
des deux côtés avant de procéder à
l’installation.
Attachez le radiateur et les ventilateurs,
comme illustré. Pour des performances
de refroidissement optimales, nous vous
recommandons d’installer les ventilateurs
comme une entrée d’air sur la tour de votre
ordinateur.
2. INSTALLATION DES VENTILATEURS ET DU RADIATEUR
Retirezlessupportsdexation
AMD AM4 existants indiqués.
3. PRÉPARATION DE LA CARTE MÈRE POUR L’INSTALLATION
1. INSTALLATION DU SUPPORT DE FIXATION AMD AM4

FRANÇAIS
FRANÇAIS

G
Veuillez passer à la page 10 pour procéder à la suite de l’installation.
Alignez le support avec les entretoises
AMD AM4 comme indiqué. Serrez
complètement les écrous à serrage
à main (F).
> Placez les entretoises AMD AM4 fournies
dans le socket de processeur.
> Serrez les quatre vis jusqu’à ce qu’elle
 soientsolidementxées.
5. INSTALLATION DE LA POMPE
4. INSTALLATION DES VIS D’ENTRETOISE AMD AM4