Courtyard Casual Sheldon 5531 Instruction sheet

Page 1 of 8
5531/Sheldon Lounge Chair with cushion

2-Person Assembly
15 Minutes Assembly Time
1. Choose an assembly location that is flat and in close
proximity to where product will be used.
2. To prevent scratching of finish, assemble on
clean, soft surface such as carpet or cloth.
3. Remove all packing material, staples, and packing
straps from the carton. Carefully unpack product.
4. Review Part List and Hardware List and ensure all
components are present and in good condition. For
missing or damaged components contact:
[e-mail]
1. KEEP ALL HARDWARE OUT OF REACH OF
CHILDREN.
2. TO AVOID ANY RISK OF SUFFOCATION TO
CHILDREN AND ANIMALS, DISPOSE, PLASTIC
PACKING MATERIAL IMMEDIATELY.
1. Prior to each assembly step, identify the required parts
and hardware.
2. DO NOT over-tighten hardware, damage may occur.
3. DO NOT use power tools during assembly.
4. DO NOT sit or stand on partially assembled product.
1. Rated for residential (non-commercial) use only.
2. Product holds a maximum of 250lbs exceeding
this limit damage on product and may cause injury.
3. Keep fingers away from hinged area of product.
4. Product is designed for use by one person at
a time.
5. DO NOT use product if any component becomes
damaged. Check all hardware periodically and re-tighten
as necessary.
6. DO NOT stand on product. Use only for intended
purpose.
7. DO NOT drag product across floor. Exercise care when
moving product.
8. DO NOT place hot items directly onto product surface.
9. DO NOT use harsh abrasives or commercial cleaners.
Wipe with soft, damp cloth.
10. DO NOT allow liquid of any kind to remain on product.
Absorption may cause surface damage.
ASSEMBLY REQUIREMENT
ASSEMBLY PREPARATION
SAFETY PRECAUTION
ASSEMBLY PRECAUTION
CARE AND USE
MADE IN VIETNAM
5531/Sheldon Lounge Chair with cushion
Page 2 of 8

A: Right leg (1) B: Left leg (1)
D: Right arm (1)
M: Allen Key (1)
J: Hexagon bolt M6x75 (8)
C: Support leg (3)
E: Left arm (1)
Part List
F: Seat part 1 (1)
G: Seat part 2 (1) H: Seat part 3 (1) I: Cushion (1)
L: Hexagon bolt M6x35 (12)
K: Hexagon bolt M6x50 (6)
Page 3 of 8
Before beginning assembly, separate all parts and carefully study the parts diagrams below. Review all
parts and hardware before disposing of any packaging. You may receive extra hardware with your unit.
Contact Kingston Casual Customer Service at for missing hardware. [email protected]
5531/Sheldon Lounge Chair with cushion

K 6pcs
Attach Right leg (A) and Left leg
(B) to Support leg (C) using
Hexagon bolt M6x50 (K).
Tighten Hexagon bolt M6x50 (K)
100% with Allen Key (M).
Assembly Instructions
STEP 1
B
C
A
K
K
KM
Page 4 of 8
100%
5531/Sheldon Lounge Chair with cushion

Attach Seat part 1 (F), Seat part 2
(G) and Seat part 3 (H) to Right
arm (D) using Hexagon bolt
M6x35 (L).
Tighten Hexagon bolt M6x35 (L)
100% with Allen Key (M).
Assembly Instructions
STEP 2
M
L
HG F D
L
L 6pcs
Page 5 of 8
100%
5531/Sheldon Lounge Chair with cushion

Attach group Seat part 1 (F),Seat
part 2 (G), Seat part 3 (H) and
Right arm (D) to Left arm (E) using
Hexagon bolt M6x35 (L).
Tighten Hexagon bolt M6x35 (L)
100% with Allen Key (M).
Assembly Instructions
STEP 3
E
LM
Page 6 of 8
L 6pcs
100%
L
5531/Sheldon Lounge Chair with cushion

Attach group Right leg (A) Left
leg (B) and Support parts (C) to
group Seat part (G), Seat part (H),
Right arm (D) and Left arm (E)
using Hexagon bolt M6x75 (J).
Tighten Hexagon bolt M6x75 (J)
100% with Allen Key (M).
Assembly Instructions
J 8pcs
JM
JJ
STEP 4
Page 7 of 8
100%
5531/Sheldon Lounge Chair with cushion

Rotate the chair, put the cushion(I)
to seat part and cinch cushion (I)
to seat part of the chair.
Assembly is complete.
The chair is ready for use.
Assembly Instructions
STEP 5
I
Page 8 of 8
5531/Sheldon Lounge Chair with cushion