Cozy N Safe APOLLO EST308 User manual

EST308

DEAR CUSTOMER
Thank you for purchasing the Cozy N Safe Apollo car seat! We couldn’t be more thrilled to be
part of your journey with your little one.
In order to ensure the safety of your child, please be sure to install and
use this child car seat correctly as described in this manual. Please keep the manual
secure for reference when needed. If you have any questions when using this product
please feel free to contact us.
For warranty information please check our website at www.cozynsafe.com
View the fitting video at www.cozynsafe.com
CONTENTS
1. Notice
2. Position In Vehicle
3. Pre-installation preparation / Features
3.1 ISOFIX
3.2 Headrest adjustment when using 5-points harness
(Group 0+/1)
3.3 Headrest adjustment when using 3-point belt (Group 2/3)
3.4 Recline adjustment and rotation
4. Rearward Facing Installation Instructions
4.1 Group 0+/1 (0-18kg ) ISOFIX+Top tether
Using 5-point harness
4.2 Group 0+/1 0-18kg 3 point belt+5 points harness
5. Forward Facing Installation Instructions
5.1-1 Group 1 (9-18kg) 3-point seat belt using 5-point harness
5.1-2 Group 1 (9-18kg) ISOFIX+ 3-point seat belt
using 5-point harness
5.2-1 Group 2/3 (15-36kg) 3-point seat belt
5.2-2 Group 2/3 (15-36kg) 3-point seat belt + ISOFIX
6. Removing The Car Seat From Your Vehicle
7. Cleaning The Covers

3. It is certified that this seat complies with ECE R/44 regulations and can be installed on most vehicles that comply with
ECE R/16 or other equivalent standards.
4. For your child's safety, please read the instructions carefully. Failure to use this child car seat correctly increases the risk
of serious injury or death
4.1 The 5-point harness can be used for children weighing up to 18kg (approximately 4 years old).
4.2 This product can also be used for children weighing 15-36kg (approximately 3-12 years old), by hiding the harness and
using the vehicle’s 3-point seat belt instead.
4.3 All straps should be fastened tightly to the child’s body and must not be twisted.
4.4 Always ensure all belts and harnesses are properly fitted, and ensure any lap belts are worn low down so that the pelvis
is firmly engaged
4.5 After an accident of any kind, the child safety seat should be replaced as unseen damage could have occurred.
4.6 Do not modify this car seat or use any accessories that haven’t been supplied by this manufacturer
4.7 The seat can become very hot if left in direct sunlight. Contact with these parts could result in burning. Always touch the
surface of any metal or plastic parts before putting your child in the seat.
4.8 Never leave children alone in the child safety seat when unattended.
4.9 Secure luggage and other objects in the vehicle, they are liable to cause injury in the event of a collision.
4.10 This product must be used with a cover. Do not use any other covers other than those recommended by the
manufacturer. Covers contribute to the overall performance of the product.
4.11 This product is suitable for children weighing 0kg-36kg.
4.12 This product should always be used in a rear facing position until the child is 9kg, and cannot be installed on the
front seat with an active air bag. When using the seat in a forward position, always try to install the safety seat in the rear seat.
The front seat with an air bag can seriously injure the child.
4.13 This manual should be stored with the child safety seat during the products’ life.
4.14 This product is not designed for home use, it can only be used in the car, please do not use it in the home.
4.15 When there is no child in the child car seat, it must be secured or stored in the trunk of the car.
4.16 During the daily use of the vehicle, make sure that all parts of the child safety seat are fixed in the correct position
and are not liable to get stuck on a movable seat or door.
4.17 Before adjusting any movable or adjustable parts of the child safety seat, remove the child out of the safety seat.
4.18 Do not buy second-hand child safety seats, you have no way of knowing the history of the seat.
It is likely it could have unseen damage, or key components may be missing.
4.19 Do not use any other load bearing points other than those indicated.
4.20 If the position of the adult safety-belt buckle relative to the main load bearing contact points on the child safety seat
is unsatisfactory. Please contact the manufacturer if in doubt about this point.
1
NOTICE
1. Please read the manual carefully, incorrect installation may cause serious injury, if in doubt please contact the
manufacturer or the retailer.
2. The Apollo is suitable for children from birth to 36 kg (Group 0+/1/2/3, from birth to approx. 12 years old.)
Below is a table for the appropriate fitting methods based on your child’s weight.
Group 1
Group 1
Group 2/3
Group 2/3
Group 0+/1
Group 0+/1 0- 18KG
0- 18 K G
9- 18 K G
9- 18 K G
15- 36K G
15- 36K G
ISOFIX + Top tether using 5-point harness (rearward facing)
3-point belt using 5-point harness (rearward facing)
ISOFIX + 3-point seat belt using 5-point harness (forward facing)
3-point seat belt using 5-point harness (forward facing)
3-point seat belt (forward facing)
ISOFIX + 3-point seat belt (forward facing)
1 2

Products without certification and modified products are dangerous, and it is also dangerous if there are no installation instructions provided
by the manufacturer. If the adult seat belt interferes with the position of the main load bearing point of the child restraint system, it cannot be used.
If you have any questions about this, please contact the manufacturer of the child restraint system. 2
Position In Vehicle
3 4
F R O N T
C A R
Y e s
R E A R
C e n t r e
N O
r e f e r t o
v e h i c le l i s t
O u t e r
Y e s
Notice regarding Universal category (Group 0+ I II III）
1. This is a “Universal” child restraint. It is approved to Regulation
No. 44, 04 series of amendments, for general use in vehicles and it will fit
most, but not all, car seats.
2. A correct fit is likely if the vehicle manufacturer has declared in the
vehicle handbook that the vehicle is capable of accepting a “Universal”
child restraint for this age group.
3. This child restraint has been classified as “Universal” under more
stringent conditions than those which applied to earlier designs which do
not carry this notice.
4. If in doubt, consult either the child restraint manufacturer or the retailer.
Notice regarding Semi- universal category (Group 0+ I II III )
This child restraint is classified for " Semi- universal" use and is suitable
for fixing into the seat positions of the following cars:
Seat positions in other cars may also be suitable to accept this child restraint. If in
doubt, consult either the child restraint manufacturer or the retailer.
Notice regarding Semi- universal ISOFIX child restraint system (in Group 0+ )
1. This is an ISOFIX CHILD RESTRAINT SYSTEM. It is approved to Regulation
No. 44, 04 series of amendments for general use in vehicles fitted with ISOFIX
anchorages systems.
2. It will fit vehicles with positions approved as ISOFIX positions (as detailed in the
vehicle handbook), depending on the category of the child seat and of the fixture.
3. The mass group and the ISOFIX size class for which this device is intended is:
Group 0+, D

2.1 Rearward facing
Danger! When the child seat is installed in a rear facing position,
being hit by the air bag, may cause injury or
even death of the child.
Under no circumstances can this child safety seat be
used on a car seat with an airbag activated.
Please read the instructions carefully to use the child safety seat correctly
Correct fit Incorrect fit
Do not install the child safety seat at the front seat with air bag.
Only with the three point safety belt, in this location.
2.2 Forward facing
①
②
DIAGONAL BELT
LAP BELT
Correct fit Incorrect fit
Only suitable if the approved vehicles are fitted with 3 point safety belts,
approved to UN/ECE Regulation No.16 or other equivalent standards.
Do not install the child safety seat on the front seat with an air bag.
Only with the three point safety belt, in this location.
5 6

3
Pre-Installation Preparation / Features
3.1 ISOFIX
(Figure 3.1.1 ) (Figure 3.1.2 )
2. Press the ISOFIX release button (13) and
extend it out to its’ furthest point.
(Figure 3.1.2)
If your vehicle is not equipped with ISOFIX guides,
please insert the two ISOFIX guides (02) included
with this child safety seat on to the ISOFIX
contact point (01)
(Figure 3.1.1).
Tip: The ISOFIX points are located between the seat
and the backrest. Please refer to the
car manufacturer's manual.
7 8

2. The headrest (08) must be
adjusted to approximately two fingers
between the child's shoulder and the
bottom of the headrest (08).
The correctly adjusted headrest (08)
ensures that the diagonal part (09)
of the car seat belt is in the correct
position, to provide the best
protection for your child.
(Figure 3.3.2)
3.2 Headrest adjustment when using 5-point harness (Group 0+/1) 3.3 Headrest adjustment when using 3-point belt (Group 2/3)
1. Press the Harness Release (04) and
pull out the two shoulder belts (05)
at the same time. Please do not pull the
shoulder pads (06).
(Figure 3.2.1)
(Figure 3.2.2)(Figure 3.2.1)
2. Pull up the headrest adjustment ring
(07), adjust the headrest (08) to a suitable
position for the child and release the ring.
(Figure 3.2.2)
1. Pull up the headrest adjustment ring
(07), adjust the headrest (08) to a suitable
position for the child and release the ring.
(Figure 3.3.1)
Tip: Where the shoulder straps on the harness enter the back
of the child car seat. They should sit level with the child’s shoulder.
(Figure 3.3.1) (Figure 3.3.2)
9 10
06
05
04
08 07 08 07 08
09

3.4 Recline adjustment and rotation
(F ig ure 3.4 . 1) (F ig ure 3.4 . 2) (F ig u re3 .4 .3)
1. Pull the recline/rotation handle (10) in the direction of the arrow.
You can then recline the seat to the appropriate recline position.
Release the recline/rotation handle (10), and the car seat will be
automatically locked again. (Figure 3.4.1) (Figure 3.4.2)
4
Rearward Facing Installation Instructions
11 12
10 32
11
1. Pull the recline/rotation handle (32)
in the direction of the arrow.
You can then rotate the seat.
Release the recline/rotation handle (32),
and the car seat will be automatically
locked again when in a correct position.
Always check that the car seat is locked
in position before travelling.
(Figure 3.4.3)

4.1 Group 0+/1 (0-18kg ) ISOFIX+Top tether Using 5-point harness
Please refer to chapter 3.1 to prepare the ISOFIX.
Please refer to chapter 3.2 to adjust the 5-point harness
Please refer to chapter 3.4 to place the seat in recline
position 1. When using the car seat for group 0+ the seat should
be rear facing.
(Figure 4.1.1)
(Figure 4.1.3) (Figure 4.1.4)(Figure 4.1.2)
Note: The ISOFIX connector (12) is installed correctly only when the ISOFIX indicator turns completely green.
1. Please connect the two
ISOFIX connectors (12)
Insert the connectors into the
ISOFIX guides and on to the
ISOFIX connection points until
you hear a "click" sound, the
ISOFIX indicator will turn green.
(Figure 4.1.1) (Figure 4.1.2)
2. Push the car seat firmly towards
the back of the vehicle seat until it
wont go any further. (Figure 4.1.3)
Pushing one side at a time
might help.
3. Press and hold the release button
of the top tether and extend the top
tether belt to give yourself some slack.
(Figure 4.1.4)
13 14
12
1
12
13

4. Feed the top tether belt into one
of the routing guides (14) on the
shoulder of the car seat furthest
away from the door.
(Figure 4.1.5)
(Figure 4.1.6)
5. Please hook the top tether
fixing hook on to one of the
recommended anchor points
as per the vehicles’ user manual.
(Figure 4.1.7)
(Figure 4.1.5) (Figure 4.1.6) (Figure 4.1.7 )
(Figure 4.1.8)
6. Pull the free end of the top
tether belt to tighten until the
indicator of the top tether turns
completely green. (Figure 4.1.8)
7. The seat is now ready
for your child.
After rotating the seat you should
always check the top tether
indicator to ensure it is still green.
14
1. Adjust the seat recline to position 1 and place
the car seat in rear facing position
4.2 Group 0+/1 0-18kg 3 point belt + 5 point harness
2. Pull the car's 3 point seat belt to the longest
length.
1 2
15 16

5. Buckle up the car’s 3 point seat belt
and pull the seat belt as tight as it will
go.
3. Pass the diagonal strap of the cars’
3 point seat belt between the headrest
and shell of the seat. Then through
the seat belt guide hook on the
“shoulder” of the seat.
4. Lift the insert and then pass the
lap belt through the bottom
of the seat following the guides.
17 18
3 4 5
1. To use the 5-point harness,
press the button to open the
5-point safety buckle (19),
press the central adjuster
(this is marked on the covers
with a circle and PRESS) (04)
and pull out the shoulder belts (05).
Please do not pull the shoulder
pads (06). (Figure 4.1.9)
(Figure 4.1.9) (F ig ure 4 .1 .1 1 )
2. Make sure that the child's back rests flat
on the car seat. Close the two clasps (20)
of the 5-point safety buckle first,
and then insert into the buckle.
When it is locked, you will hear a “click”.
(Figure 4.1.10) (Figure 4.1.11)
(Figure 4.1.12)
3. Pull the harness adjustment belt (21)
until the 5-point harness is close to the
child and not loose.
(Figure 4.1.13) (Figure 4.1.14)
06
05
19
04
20
20
19
(F igu re 4 .1. 10 )

5
Forward Facing Installation Instructions
In order to ensure the safety of your child, please check the following items after each installation:
1. Make sure that the two ISOFIX connectors are correctly connected to the vehicle ISOFIX connection points, and the
ISOFIX connection indicators are completely green.
2. Ensure that the child car seat is tightly attached to the vehicle seat.
3. Make sure that the top tether is tight and the top tether indicator is green.
4. Make sure that the 5-point harness is close to, but not squeezing the child.
5. Make sure that the shoulder straps are adjusted correctly and not twisted.
6. Make sure that the height of the shoulder pads is the same as the height of the child's shoulders.
7. Make sure that the 5-point buckle is locked.
(F ig ure 4 .1 .1 2 ) (F ig ure 4 . 1.1 3 ) (F ig ure 4 .1 .1 4 )
19 20
06
06
05 21

Please make sure that the 5-point harness is correctly installed on the child safety seat
and not twisted.
Please refer to chapter 3.2 to adjust the 5-point harness.
Please refer to chapter 3.4 to adjust the recline position and that it is locked in position.
Please refer to chapter 3.5 to rotate the car seat to a forward facing position.
Please place the child safety seat on the vehicle seat in the same direction as the vehicle.
(Figure 5.1.1)
Pull out the 3-point safety belt of the vehicle to give yourself some slack.
Feed the diagonal part of the belt through the routing guide on the shoulder of child car seat.
(Figure 5.1.2) Then continue to feed the diagonal part between the headrest and the shell.
Feed the lap belt through the routing guides on the bottom of the seating area (Figure 5.1.3)
and continue to feed both parts of the vehicle belt across the seat putting the belts behind the infant
inserts and sleeping pads. (As per in Figure 5.1.4) Feed both parts of the vehicle 3 point belt through the guide on the opposite side of the bottom of the seat (Figure 5.1.4)
Then clip the 3 point belt into the vehicle buckle and pull to remove any slack in the belts.
Remember to check to ensure the belts are not twisted.
In order to ensure the safety of the child, please check the following items after each installation:
1. Make sure that the vehicle seat belt is not twisted and is tight.
2. Make sure that the child safety seat is close to the vehicle seat.
3. Make sure that the 5-point harness is close to the child, but not squeezing the child.
4. Ensure that the shoulder strap is in the correct position and not twisted.
5. Make sure that the height of the shoulder pad is the same as the height of the child's shoulders.
6. Ensure that the 5-point buckle is locked.
(Figure 5.1.5)(Figure 5.1.4)(Figure 5.1.3)
(Figure 5.1.1)
(Figure 5.1.2)
21 22
23
11
22
Group I (9-18kg) 3-point seat belt using 5-point harness
5.1-1
①②
1
2

(Figure 5.1.6) (Figure 5.1.7) (Figure 5.1.8) (Figure 5.1.9) (Figure 5.1.10) (Figure 5.1.11)
23 24
06
06
05 21
06
05
19
04
20
19
1. To use the 5-point harness,
press the button to open the
5-point safety buckle (19),
press the central adjuster
(this is marked on the covers
with a circle and PRESS) (04)
and pull out the shoulder belts (05).
Please do not pull the shoulder
pads (06). (Figure 5.1.6)
2. Make sure that the child's back rests flat
on the car seat. Close the two clasps (20)
of the 5-point safety buckle first,
and then insert into the buckle.
When it is locked, you will hear a “click”.
(Figure 5.1.7) (Figure 5.1.8)
3. Pull the harness adjustment belt (21)
until the 5-point harness is close to the
child and not loose.
(Figure 5.1.10) (Figure 5.1.11)
In order to ensure the safety of your child, please check the following items after each installation:
1. Make sure that the two ISOFIX connectors are correctly connected to the vehicle ISOFIX connection points, and the
ISOFIX connection indicators are completely green.
2. Ensure that the child car seat is tightly attached to the vehicle seat.
3. Make sure that the top tether is tight and the top tether indicator is green.
4. Make sure that the 5-point seat harness is close to the child, but not squeezing the child.
5. Make sure that the shoulder straps are adjusted correctly and not twisted.
6. Make sure that the height of the shoulder pads is the same as the height of the childs’ shoulders.
7. Make sure that the 5-point buckle is locked.

12
(Figure 5.1.5)
(Figure 5.1.4)
(Figure 5.1.3)
(Figure 5.3.1)
(Figure 5.1.2)
25 26
23
11
22
5.1-2 Group 1 (9-18kg) ISOFIX+ 3-point seat belt
using 5-point harness
Please make sure that the 5-point harness is correctly installed on the child safety seat
and not twisted.
Please refer to chapter 3.2 to adjust the 5-point harness.
Please refer to chapter 3.4 to adjust the recline position and ensure that it is locked in position.
Please refer to chapter 3.5 to rotate the car seat to a forward facing position.
Press the ISOFIX release button and extend the ISOFIX connectors out to their
furthest point. Attach the ISOFIX connectors to the anchor points in the vehicle.
The safety indicator will turn green when they are securely locked. Push the child
car seat back towards the vehicle seat as far as it will go. Using a knee may help with
this.
Pull out the three-point safety belt of the vehicle to give yourself some slack.
Feed the diagonal part of the belt through the routing guide on the shoulder of child car seat.
(Figure 5.1.3) Then continue to feed the diagonal part between the headrest and the shell.
Feed the lap belt through the routing guides on the bottom of the seating area (Figure 5.1.2) and continue to feed both
parts of the vehicle belt across the seat putting the belts behind the infant inserts and sleeping pads.
(As per in Figure 5.1.4)
Feed both parts of the vehicle 3 point belt through the guide on the opposite side of the bottom of the seat (Figure 5.1.4)
Then clip the 3 point belt into the vehicle buckle and pull to remove any slack in the belts.
Remember to check to ensure the belts are not twisted.
In order to ensure the safety of the child, please check the following items after each installation:
1. Make sure that the vehicle seat belt is not twisted and is tight.
2. Make sure that the child safety seat is close to the vehicle seat.
3. Make sure that the 5-point harness is close to the child, but not squeezing the child.
4. Ensure that the shoulder strap is in the correct position and not twisted.
5. Make sure that the height of the shoulder pad is the same as the height of the child's shoulders.
6. Ensure that the 5-point buckle is locked.
①②
1
2

27 28
(Figure 5.1.6 ) (Figure 5.1.7 ) (Figure 5.1.8) (Figure 5.1.9) (Figure 5.1.10) (Figure 5.1.11)
06
06
05 21
06
05
19
04
20
19
1. To use the 5-point harness,
press the button to open the
5-point safety buckle (19),
press the central adjuster
(this is marked on the covers
with a circle and PRESS) (04)
and pull out the shoulder belts (05).
Please do not pull the shoulder
pads (06). (Figure 5.1.6)
2. Make sure that the child's back rests flat
on the car seat. Close the two clasps (20)
of the 5-point safety buckle first,
and then insert into the buckle.
When it is locked, you will hear a “click”.
(Figure 5.1.7) (Figure 5.1.8)
3. Pull the harness adjustment belt (21)
until the 5-point harness is close to the
child and not loose.
(Figure 5.1.10) (Figure 5.1.11)
In order to ensure the safety of your child, please check the following items after each installation:
1. Make sure that the two ISOFIX connectors are correctly connected to the vehicle ISOFIX connection points, and the
ISOFIX connection indicators are completely green.
2. Ensure that the child car seat is tightly attached to the vehicle seat.
3. Make sure that the 5-point harness is close to, but not squeezing the child.
4. Make sure that the shoulder straps are adjusted correctly and not twisted.
5. Make sure that the height of the shoulder pads is the same as the height of the child's shoulders.
6. Make sure that the 5-point buckle is locked.

5.2-1 Group 2/3 (15-36kg) 3-point seat belt
Please ensure that the 5-point harness is properly hidden.
Ensure the headrest is in the correct position for your child (see chapter 3).
Ensure the seat is locked in a forward facing position and is locked into recline position 1.
You are unable to use any other recline position other than position 1 in this weight group.
Place the child safety seat on the vehicle seat in the same direction as travel (forward facing)
Pull out the vehicle 3-point belt around the child, and buckle it up. You will hear a “click” (24), when it is locked.
Warning : Ensure that the vehicle 3-point belt is not twisted
Place the lap part of the vehicle belt (26) and diagonal part of the belt (25) (on the same side of the
vehicle 3-point belt buckle) (24)-under the child's arm and place both parts in the belt guide groove (27) (Figure 5.2.2)
(Figure 5.2.1 ) (Figure 5.2.2 )
Place the other side of the lap part of the vehicle belt (26)
in the belt guide groove (28) on the other side of the child
car seat. (Figure 5.2.3)
Feed the diagonal part of the vehicle seat
belt (29) into the belt guide of the headrest (30)
and ensure that the vehicle seat
belt is not twisted. (Figure 5.2.4) Please make sure
that the diagonal part of the seat belt (29) sits
on the child's collarbone, not on the child's neck.
Tip: If necessary, you can adjust the headrest.
(Figure 5.2.3) (Figure 5.2.4)
29 30
08
08
24
28
26
25
26
27
30
1
In order to ensure the safety of your child, please pay attention to the following items after each installation:
1. Make sure that both the diagonal part of the belt (25) and lap part of the belt (26) on the side of the car seat belt buckle (24)
are placed in the belt guide groove (27).
2. Make sure that the other side of the lap part of the belt (26) is placed in the belt guide groove (28) (Figure 5.2.3).
3. Ensure that the diagonal part of the belt (29) is placed in the belt guide (30) on the headrest (08).
4. Ensure that the diagonal part of the belt (29) is placed on the child's collarbone, not on the child's neck.
5. Ensure that the vehicle seat belt is not twisted and is tight to the child’s body.

5.2-2 Group 2/3 (15-36kg) 3-point seat belt + ISOFIX
Please ensure that the 5-point harness is properly hidden.
Ensure the headrest is in the correct position for your child (see chapter 3).
Ensure the seat is locked in a forward facing position and is locked into recline position 1.
You are unable to use any other recline position other than position 1 in this weight group.
Place the child safety seat on the vehicle seat in the same direction as travel (forward facing)
1. Please connect the two ISOFIX connectors. Insert the ISOFIX connectors into the ISOFIX guides and on to the
ISOFIX connection points until you hear a "click" sound, the ISOFIX indicator will turn green.
Push the car seat firmly towards the back of the vehicle seat until it wont go any further. (Figure 5.2.1)
Pushing one side at a time or using your knee might help.
Pull out the vehicle 3-point belt around the child, and buckle it up. You will hear a “click” (24), when it is locked.
Warning : Ensure that the vehicle 3-point belt is not twisted.
Place the lap part of the vehicle belt (26) and diagonal part of the belt (25)
(24)-under the child's arm and place both parts in the belt guide groove (27) (Figure 5.2.3)
31 32
12
(Figure 5.2.2)(Figure 5.2.1) (Figure 5.2.3)
(Figure 5.2.4)(Figure 5.2.5)
08
08
24
28
26
25
26
27
1
Place the other side of lap part of the belt (26)
in the belt guide groove (28) on the other side of the child
car seat. (Figure 5.2.4)
Feed the diagonal part of the vehicle seat
belt (29) into the belt guide of the headrest (30)
and ensure that the vehicle seat
belt is not twisted. (Figure 5.2.4) Please make sure
that the diagonal part of the seat belt (29) sits
on the child's collarbone, not on the child's neck.
Tip: If necessary, you can adjust the headrest.
30
In order to ensure the safety of your child, please pay attention to the following items after each installation:
1. Make sure that both the diagonal part of the belt (25) and lap part of the belt (26) on the side of the car seat belt buckle (24)
are placed in the belt guide groove (27).
2. Make sure that the other side of the lap part of the belt (26) is placed in the belt guide groove (28) (Figure 5.2.3).
3. Ensure that the diagonal part of the belt (29) is placed in the belt guide (30) on the headrest (08).
4. Ensure that the diagonal part of the belt (29) is placed on the child's collarbone, not on the child's neck.
5. Ensure that the vehicle seat belt is not twisted and is tight to the child’s body.

33 34
6
Removing The Car Seat From Your Vehicle
Red indicator means
ISOFIX is unlocked
Green indicator means
ISOFIX is locked
Press the ISOFIX release button to unlock the ISOFIX. When the
safety indicator turns from green to red, it means that the
ISOFIX is disconnected from the vehicle.
Continue to slide the connectors into the base.
Remove all of the vehicle belts and then the seat can be
removed from the vehicle.
7
Cleaning The Covers
The cloth cover of the child safety seat can be
removed and washed. Disassembly of the cloth
cover:
1. Adjust the headrest to the highest position.
2. Remove the headrest cover by removing any toggles
and poppers and stretching the elastic parts of the
cover over the headrest.
3. Remove the chair body cover by removing any toggles
and poppers and stretching the elastic parts of the
cover over the seat.
Hand wash with water temperature not exceeding 30°C.
Use neutral detergent. Only hand wash, do not bleach,
dry flat, do not tumble dry, do not iron, do not dry clean,
do not use bleach or furniture detergent
P
30°C