Cozy N Safe Apollo User manual

Euro Stock Traders Ltd
Cozy N Safe
Oxford Street, Wolverhampton, West Midlands, WV14 7DP, U.K.
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.cozynsafe.com
EST-01AECE R16 No44/04 Group 0+/1
IsoFix Classificaon: B1
INSTRUCTION MANUAL
Please read carefully before use.

1
COZY N SAFE GROUP 0+/1 CAR SEAT INSTRUCTION MANUAL
From Birth to 18kg ( Birth - 4 years approx.)
2
1. Warnings
2. Product composion
3. Installaon posions within the vehicle
4. Setup within the vehicle
5. Installaon in the vehicle / Group 0+
5.1. Installing the child seat
5.2. Fastening the child into the seat
6. Installaon in the vehicle / Group 1
6.1. Installing the child seat with ISOFIX and Top tether
6.2. Installing the child seat with three point belt
6.3. Fastening the child into the seat
7. Adjusng the seat
8. Child seat care and maintenance
9. Warranty
CONTENTS
03-04
05-06
07
08
09-12
13-17
17
18
19

3
1. WARNINGS
Please read carefully before installing the child seat in the vehicle.
1. This child safety seat is suitable for use as group 0+/1
from birth to 18kg (Birth to 4 years age approx.)
2. Please read these instrucons carefully, as incorrect installaon
could result in serious injury. If any injuries should occur as a
result of incorrect installaon, the manufacturer will accept no
responsibility.
3. This child seat is in accordance with the ECE R44/04 regulaons
and may be installed in the majority of vehicles equipped with
approved points, such as ISOFIX points, in accordance with ECE
regulaon 16, However, prior to purchase, the child seat should
always be tested in your vehicle with the child seated, in order
to ensure that the model meets your needs.
4. Never use the child safety seat without its cover.
5. Protect the child safety seat from direct sunlight, as the seat can
get very hot and harm the child.
6. Child seats or accessories that are damaged or have been used
incorrectly must be replaced.
7. Do not leave heavy objects inside the car, as these may injure
the child in the event of an accident.
4
1. WARNINGS
8. Ensure that no part of the child seat is caught in the door of the
vehicle or in a reclining seat. In addion, ensure that the safety
seat is correctly installed and secured.
9. Do not disassemble, modify, or add any piece to the child seat
or harness, as this would seriously affect its basic funconing
and the safety that the child seat provides.
10. The safety seat must remain installed in the vehicle. Even if the
child is not seated in the car seat. The child must never be le
unaended while seated in the safety seat, not even outside
the vehicle.
11. Keep the safety seat away from corrosive products.
12. The manufacturer guarantees the quality of its products, but
not the quality of send-hand products or products belonging
to other companies.
13. Instrucon illustraons are for informaonal purposes only.
The child restraint system may contain small differences
compared to the photographs or images in the instrucon
manual.

2. PRODUCT COMPOSITION
5
Top tether hook
Headrest height adjuster
Shoulder pads
5-point harness buckle
Center adjuster
Harness
adjustment
strap
Seat
recline
lever
ISOFIX connector
release buon
ISOFIX connector
Headrest
Top tether
adjuster
6
2. PRODUCT COMPOSITION
Upper belt
guider
Below belt guider
Sha
Lock-off
device
0+ base
ISOFIX connector
inseron guider

7
3. INSTALLATION POSITIONS WITHIN THE VEHICLE
Facing the direcon of travel (group 1)
Facing away from the direcon of travel (group 0+)
With the 2-point belt (car seatbelt)
With the front airbag
On seats with:
Group 1:
(1) ISOFIX anchorage points (between the seat and
the seat back) and top tether anchorage points (such as on the rear
shelf, on the ground or behind the seat)
(2) 3-point seatbelts Group 0+: 3-point seatbelts
Group 0+ Group 0+/1
8
4. SETUP WITHIN THE VEHICLE
fig.1 fig.2
Place the child seat in the rear of the vehicle, facing away from the
direcon of travel(group 0) or facing forward(group1).
The child seat must be as closely ached to the vehicle's seat as
possible.
For vehicles with adjustable headrests, a beer installaon can be
achieved by adjusng the height or removing the
headrest(fig.1)(Group1).
It is important to replace the headrest in its posion when an adult
is travelling.
The child seat must not be transported in the vehicle without being
buckled in, even when the child is not travelling in the child seat. It
is very important to keep this in mind, in order to avoid any damage
that the child seat could cause in the event of an accident. The child
seat must therefore remain installed at all mes while driving.
Ensure that the distance between the child seat, installed in the rear
of the vehicle, and the front seats is the maximum possoble.(fig.2).

9
5. INSTALLATION IN THE VEHICLE / GROUP 0+
4
2 3
5.1 INSTALLING THE CHILD SEAT
ONLY GROUP 0+
From Birth to 13kg (9 months to 13kg approx.)
1. Connect the seat to the 0+ base by inserng it into the holes
on the top of the child seat base. (fig.1)
2. Recline the child seat fully. Pull the seat recline lever upwards.
Recline the seat while keeping hold of the lever.
Release the lever when the seat is in the most reclined posion.
(fig.2)
3. Place the child seat in the rear of the vehicle, facing away from
the direcon of travel. (fig.3)
4. Turn unlock the sha and pull it out. (fig.4)
1
10
5. INSTALLATION IN THE VEHICLE / GROUP 0+
5. Pull away the seat shell away from the seat base, insert
3-point seatbelt through seat shell and seat base.(fig.5)
6. Abdomen part of the 3-point seatbelt go through two below
belt guiders, lock 3-point seatbelt unl you hear a “click”.
Then shoulder part of 3-point seatbelt go through one upper
belt guider which is close the retractor. (fig.6)
7. Push together the seat shell and seat base, insert back and
turn locked the sha. Pulling the 3-point seatbelt to remove
any slack, and make sure there is no twist. (fig.7)
57 6

11
5. INSTALLATION IN THE VEHICLE / GROUP 0+
5.2 FASTENING THE CHILD INTO THE CHILD SEAT
1. The correct adjustment of the headrest ensures that the child
is properly fastened into the car seat. The headrest must be
adjusted so that the harness(which moves with the headrest)
is at shoulder height on the child or slightly above, but never
behind the back or at the ear level (fig1)
2. Pull the headrest height adjuster and move headrest to
shoulder height in accordance with the size of the child(fig2)
3. Loosen the harness strap by stretching the chest secon while
holding down the center adjuster(fig3).
4. Open the buckle so that the child can be placed into the seat.
The harness straps can be placed on the armrest(fig4).
5. Place the child into the seat, then fit the safety harness around
the child, using the buckle to fasten the two parts together
unl you hear a “click”(fig5)
6. Stretch the harness adjustment belt in order to give the
harness correct amount of tension. (fig 6,7)
12
5. INSTALLATION IN THE VEHICLE / GROUP 0+
4
8
6
7
5
1 2
3

13
6. INSTALLATION IN THE VEHICLE / GROUP 1
6.1 ONLY GROUP 1
From 9kg to 18kg (9 months to 4 years approx.)
6.1.1 CHILD SEAT INSTALLATION(USE ISOFIX SYSTEM)
1. Pull out the ISOFIX connectors as far as possible by pulling the
strap(fig1.)
2. Clip the inseron guides onto the ISOFIX anchorage points in
the vehicle(fig2.)
3. Guide the ISOFIX system connectors on the child seat into the
inseron guides unl they lock into the ISOFIX anchorage
points in the vehicle and there is an audible “click”. The ISOFIX
system indicator will change from red to green when the child
seat is securely locked in place(fig3)
4. Push the child seat against the car seat to check that the ISOFIX
system is fully latched, ensuring that the child seat is as close to
the car seat as possible(fig4).
6.1.2 UNINSTALLING THE ISOFIX CONNECTORS
1. Pull the release buons back to uninstall the ISOFIX system
from the child seat(fig5).
3
12
14
6. INSTALLATION IN THE VEHICLE / GROUP 1
6.1.3 INSTALLING THE TOP TETHER
1. Take the top tether and if required, lengthen the belt by
pressing the top tether brake buon to release the strap,
pulling to adjust as necessary(fig6)
2. Aach the top tether hook to the top tether anchorage point
which is recommended in the owner’s manual for your car(fig7)
Look for this symbol in your vehicle
3. To tension the top tether, remove any slack by pulling on the
free end of strap unl it is suitably ghtened. The top tether
will be properly ghtened when the tension indicator turns
completely green(fig8).
4
8
6
5
7

15
6. INSTALLATION IN THE VEHICLE / GROUP 1
6.2 CHILD SEAT INSTALLATION (USE 3-POINT SEATBELT)
Only group 1 from approx. 9 months to 4 years of age (9-18kg)
1. Place the child seat in the vehicle, facing from the direcon of
travel. Turn unlock the sha and pull it out.(fig.1)
2. Pull away the seat shell away from theseat base, insert 3-point
seatbelt through seat shell and seat base.(fig.2)
3. Belly part of the 3-poit seatbelt gothrough two below belt
guiders, lock 3-point seatbelt unl you hear a “click”. Then
shoulder part of 3-point seatbelt go through the lock-off
device. Turn the lock-off device and locked. (fig.3)
4. Pulling the 3-point seatbelt to remove any slack, and make
sure there is no twist. Push together the seat shell and seat
base, insert back and turn locked the sha. (fig.4)
1
2
3
4
16
6. INSTALLATION IN THE VEHICLE / GROUP 1
6.3 FASTENING THE CHILD INTO THE CHILD SEAT
1. The correct adjustment of the headrest ensures that the child
is properly fastened into the car seat. The headrest must be
adjusted so that the harness(which moves with the headrest)
is at shoulder height on the child or slightly above, but never
behind the back or at the ear level (fig1)
2. Pull the headrest height adjuster and move headrest to shoulder
height in accordance with the size of the child (fig2)
3. Loosen the harness strap by stretching the chest secon while
holding down the center adjuster(fig3).
4. Open the buckle so that the child can be placed into the seat.
The harness straps can be placed on the armrest(fig4).
5. Place the child into the seat, then fit the safety harness around
the child, using the buckle to fasten the two parts together unl
you hear a “click” (fig5)
6. Stretch the harness adjustment belt in order to give the harness
12 3

16
8. CHILD SEAT CARE AND MAINTENANCE
1
2
8.1 REMOVE THE COVER FOR CLEANING
The car seat cover is removable and washable. In case of light
staining, clean using a damp cloth or soapy
water. Refer to the care label attached to the
fabric cover.
8.2 REMOVE THE COVER
1. Open the Velcro fasteners on
headrest where the shoulder
belts go through, then pull
away the cover from the
headrest(g1).
2. Unhook 8 elastic hoops at the sides edge of the shell, pull
cover up and onto the seat surface.
8.3 TO REFIT THE COVER, SIMPLY REVERSE THE PROCESS,
HOWEVER ENSURE THE HARNESS AND BUCKLE ARE THE
CORRECT WAY ROUND AND NOT TWISTED.
17
6. INSTALLATION IN THE VEHICLE / GROUP 1
454
66
67
7. ADJUSTING THE SEAT
In order to make the child as comfortable as possible, the seat can
be reclined by pulling the lever under the front part of the seat.
Keep the lever pressed down as you recline the seat, releasing it
when the seat is in the desired posion.

19
9. WARRANTY
We guarantee our products against any manufacturer defect for a
period of 1 year, starng from the day of purchase.
1. The warranty does not cover defects or failures caused by
inappropriate use or non-compliance with the installaon
and maintenance safety standards described in the
instrucon guides provided with our products.
2. The warranty shall be automacally considered void if the
arcle acquired has been repaired or if an aempt has been
made to repair it by an individual that is not authorized by
our company.
20