CPS Pro-Set TLTWSAE Imperial User manual

Torque Wrench Kit
#TLTWSAE Imperial
(
5/
8
,
11/
16
,
13/
16
,
15/
16
, 1
1/
16
, 1
5/
16
)
cpsproducts.com
Instructions for Use
Français, Español, Deutsch and latest updates: www.cpsproducts.com

BEFORE USE
• To retain wrench accuracy, DO NOT
LOOSEN nuts, bolts, etc. USE ONLY
FOR TIGHTENING.
• Apply a small amount of oil between
handle and wrench body.
Note: If wrench is not used for an extended
time, turn handle to lowest torque setting
on wrench body. Rotate handle in both
directions while making a few “clicks”. This
re-lubricates the wrench.
INSTRUCTIONS
1. Select Wrench from case.
2. Insert END into socket. Wrench size
and arrow must be same side.
Fig. 1
3. Loosen Locking Knob
counterclockwise to unlock handle.
4. Select FOOT-Pound Scale Fig. 2 or
INCH-Pound scale Fig. 3
5. Determine Proper Torque Setting
For Equipment Being Serviced
(use setting specified by equipment
manufacturer).
6. To obtain torque values ending
in ‘0’, align (0) and Handle Edge
with Torque Value On Vertical
Scale See Fig. 2 and Fig. 4 .
7. For torque values NOT ending
in ‘0’, twist handle and align
appropriate handle mark at handle
edge with Torque Value On
Vertical Scale.
8. Tighten Locking Knob clockwise
to lock in your torque setting.
9. Tighten Equipment Fitting, Bolt,
Nut Until Clicks Are Felt/Heard
From Pivot Point Note: To prevent
tool damage, avoid further pressure on
wrench after torque (clicks) achieved.
Removable
Wrench End
Socket
Pivot Point
Torque
Values on
Vertical
Scale
Handle
Scale (0 to 5)
Arrow
Indicates
Tightening
Direction
Wrench
Body
Handle
Locking
Knob
Wrench Size
and Arrow
Must Be
Same Side
Handle
Edge
Fig. 1
2

Foot/Pound Scale (5-80)
Center-line
Each mark
on handle = ½
ft/lb
DOWN
UP
HANDLE
Shown is 30
ft/lbs.
Torque
Values
Fig. 2 Fig. 3
Inch/Pound Scale (60-960)
Each mark
on handle
= 6 in/lb
Handle Edge
Torque
Value Handle Scale Value Final Torque Value
5 0 5
5 +½ detent 5.5
5 +1 detent 6
5 +1 ½ detents 6.5
5 +2 detents 7
Example 1: Set Wrench to 7 ft/lb
a) Position wrench handle so Foot/Pound scale is
visible.
b) Twist handle until “0” mark aligns with Center-line
and 5 Foot/Pound torque value.
c) Twist handle RIGHT 4 detents (1 detent =
½Foot/Pound) stopping at the “2” Mark on
the Handle (while aligned VERTICALLY with the
Center-line).
d) Final setting (5 + ½ + ½ + ½ + ½ = 7)
e) Wrench is now set to 7 Foot/Pounds.
Example 2: Set Torque Wrench to
72 in/lb
a) Position wrench handle so Inch/Pound scale is
visible.
b) Twist handle until ‘0’ mark aligns with Center-line
and 60 Inch/Pound torque value.
c) Twist handle RIGHT 2 detents (2 detent = 12
Inch/Pound)
stopping at first “1” mark on handle.
d) Final setting (60 + 6 + 6 = 72)
e) Wrench is now set at 72 Inch/Pounds.
Torque
Value Handle Scale Value Final Torque Value
60 0 60
60 + ½ detent 66
60 +1 detent 72
=+
=+
3

STORAGE
1. Loosen Locking Knob. Turn Knurled Handle to lowest torque setting on Body Scale.
2. Remove Wrench End and place all components back in Storage Case.
3. Store kit in dry location.
FOOT/POund SeTTingS
On Wrench Body
Handle Scale
Setting
inCH/POund SeTTingS
On Wrench Body ACCurACy
5060
+/- 4%
(All Settings)
10 0120
15 0180
20 0240
25 0300
30 0360
35 0420
40 0480
45 0540
50 0600
55 0660
60 0720
65 0780
70 0840
75 0900
80 0960
Fig. 4
CPS PRODUCTS, INC. U.S.A. (Headquarters)
1010 East 31st Street,
Hialeah, Florida 33013, USA
Tel: [phone],
1-800-277-3808
Fax: [phone]
E-mail: [email protected]
Website: www.cpsproducts.com
CPS PRODUCTS CANADA LTD.
1324 Blundell Road
Mississauga, ON, L4Y 1M5
Tel: [phone], Fax: [phone]
E-mail: [email protected]
Website: www.cpsproducts.com
CPS PRODUCTS N.V
Krijgsbaan 241, 2070
Zwijndrecht, Belgium
Tel: [phone],
E-mail: [email protected]
CPS AUSTRALIA PTY. LTD.
109 Welland Avenue,
Welland, South Australia 5007
Tel: [phone],
E-mail: [email protected]
LOCATIONS
For the latest update(s) to these instructions, go to www.cpsproducts.com
#73-165 Rev. E
092617JA
REPLACEMENT PARTS
TLTWSAE
SAE Multi-Head Torque
Wrench Set with handle, heads
and case (
5
/
8
”, 11
/
16
”, 13
/
16
”, 15
/
16
”,
1
1
/
16
”, 1 5
/
16
”)
TLXTWSAE
Set of SAE Wrench Heads
5
/
8
”, 11
/
16
”, 13
/
16
”, 15
/
16
”, 1 1
/
16
”, 1 5
/
16
”
Jaw Sizes
TLXTWSAEW SAE Torque Wrench Handle
TLXTW58
5
/
8
”Individual wrench head
TLXTW1116
11
/
16
”Individual wrench head
TLXTW1316
13
/
16
”Individual wrench head
TLXTW1516
15
/
16
”Individual wrench head
TLXTW1L116 1
1
/
16
”Individual wrench head
TLXTW1L516 1
5
/
16
”Individual wrench head