Craftex CX424 User manual

1
MODEL CX424
1.5 HP DUST COLLECTOR
Version 1.0

2
TABLE OF CONTENTS
General Safety Instructions..................................................................... 3
CX424 Specific Safety Instructions......................................................... 4
Features.................................................................................................. 5
Physical Features ................................................................................... 6
Unpacking............................................................................................... 7
Setup ...................................................................................................... 7
Proper Grounding ................................................................................... 8
Assembly................................................................................................ 9
Test Run ................................................................................................11
Operation................................................................................................12
Maintenance ...........................................................................................12
Bag Cleaning ..........................................................................................12
Cleaning the Canister .............................................................................12
Lubrication..............................................................................................12
Wiring Diagram.......................................................................................13
Parts Breakdown.....................................................................................13
Parts Diagram.........................................................................................14
Parts List.................................................................................................15
Warranty.................................................................................................16

3

4

5
MODEL CX424 –1.5 HP DUST COLLECTOR
As part of the growing line of Craftex woodworking equipment, we are proud to offer the CX424
a 1.5-HP Dust Collector. By following the instructions and procedures laid out in this owner’s
manual, you will receive years of excellent service and satisfaction. The CX424 is a
professional tool and like all power tools, proper care and safety procedures should be
adhered to.
Motor ......................................1.5-HP, Single Phase 120 Volt, 12.5 Amps
Switch.....................................ON/OFF Switch with Removable Key
Balanced Steel Impeller..........Yes
Impeller Size ..........................10”
Air Suction Capacity ...............950 CFM
Noise Level.............................87.1 dB
Collection Bag Volume...........0.15 Cubic Meter
Upper Bags.............................One-Micron Upper Filtration Bag
Intakes....................................1 x 5”, 2 x 4”
Overall Dimension.................. L 34" (850mm) x W 22" (560mm) x H 73" (1860mm)
Mobile Base for Ease of Movement.....Yes
Weight ....................................41 Kg
Warranty.................................3 Years
CX424
FEATURES

6
UNPACKING
The dust collector is properly packaged in a
carton for safe transportation. When
unpacking, carefully inspect the carton and
ensure that nothing has been damaged.
While doing the inventory if you can not find
any part, check if the part is already
installed on the machine.
Figure-1 Inventory
CONTENTS QTY
A. Collector Ring....................................1
B. Motor / Impeller Unit..........................1
C. Top Bag.............................................1
D. Bottom Bag .......................................1
E. Base Unit...........................................1
F. Dual Inlet 4” Each..............................1
G. Hose..................................................1
H. Outlet Connector...............................1
I. Casters..............................................4
J. Hardware Bag...................................1
K. Gasket...............................................1
L. Collector Ring Supports ....................3
M. Top Bag Support...............................1
N. Hose Clamps.....................................2
O. Bag Clamps.......................................2
SETUP
Before setting up your machine you need to
read and understand this user manual
completely.
The CX424 features four casters installed to
its base unit for easy mobility. If you want to
use the CX424 as a stationary tool, do not
install the casters and find an ideal spot
where your dust collector will most likely be
positioned.
Consider your complete work environment
before placing your machine in the ideal
spot.

7
PROPER GROUNDING
Grounding provides a path of least
resistance for electric current to reduce the
risk of electric shock.
CX424 is for use on a normal 120 volt
circuit. Make sure that the machine is
connected to an outlet having the same
configuration as the plug. If an adaptor plug
is used, it must be attached to the metal
screw of the receptacle. To prevent
electrical hazards, have a qualified
electrician ensure that the line is properly
wired.
The dust collector should be wired with a
plug having 3 prongs to fit a 3 prong
grounded receptacle as shown in figure-2.
Do not remove the grounding prong to fit it
into a 2 pronged outlet.
Figure-2 120-Volts outlet for CX424
It is strongly recommended not to use
extension cords with your CX424. Always
try to position your machine close to the
power source so that you do not need to
use extension cords.
In case if you really find it necessary to use
an extension cord, make sure the extension
cord does not exceed 50-feet in length and
the cord is 14-gauge to prevent motor
damage.
WARNING!
Improper connection of the equipment-
grounding conductor can result in a risk
of electric shock. Check with a qualified
electrician if you are in doubt as to
whether the outlet is properly grounded.

8
ASSEMBLY
Follow the instructions below to assemble
your CX424.
Place the base unit upside down and install
the swivel casters to the base unit using
screws, nuts and washers provided. See
figure-3.
Figure-3 Installing the casters
Turn the base unit upright and position the
motor / impeller unit on the base unit with
the holes on both units aligned with each
other. Secure the motor / impeller unit to
the base unit using screws and washers
provided. See figure-4.
Figure-4 Installing the motor / impeller unit
on the base unit
Place the gasket on the motor / impeller
opening as shown in figure-5.
Figure-5 Positioning the gasket
Position the outlet connector onto the
gasket and the motor / impeller opening
securing it using screws and washers
provided. See figure-6.
Figure-6 Installing the outlet connector
Attach the three collector ring supports on
to the base unit and secure them using
screws, nuts and washers provided. See
figure-7.

9
Figure-7 Installing the collector ring support
Attach the collector ring to the collector ring
supports and the upper bag support to the
collector ring as shown in figure-8. Make
sure that the hose opening of the collector
ring is facing the motor / impeller.
Secure the collector ring from both sides
using screws, nuts, and washers provided.
Figure-8 Installing collector ring and the
upper bag support rod
Take the hose provided and attach it with its
one to the outlet connector and the other
end to the collector ring. See figure-9.
Use the hose clamps provided to secure
the hose on both ends.
Figure-9 Connecting the hose from the
outlet connector to the collector ring
Hang the top bag from the support and
install it around the collector ring. Secure it
using bag clamp provided.
Figure-10 Installing the top bag
Attach the foam strip to the bottom of the
collector and trim the excess and evenly
match the ends.

10
Install the collection bag to the bottom of
the collector ring and secure it by tightening
the collection bag clamp around it as shown
in Figure-11.
Figure-11 Installing the bottom bag
Attach the dual 2 X 4 inlet intake onto inlet
the cover motor/impeller opening as shown
in figure-12 and secure it using screw
provided.
Figure-12 Installing the dual intake
The dual intake has a 4” cover cap, in case
only one intake is used.
TEST RUN
Once you have assembled your dust
collector, it is then time for a test run to
make sure that the machine works properly
and is ready to use.
Remove all the tools used for assembling
the machine components. Walk around the
machine, ensure all nuts, bolts, and screws
are tightened and the machine is properly
assembled. Connect the cord to the power
source and turn the machine ON.
During the test run if there is any unusual
noise coming from the machine or the
machine vibrates excessively, turn OFF the
power switch immediately and disconnect
the cord from the power source. Investigate
to see if you can find out what the problem
with your machine.
Turn the dust collector OFF and remove the
disabling key from the ON/OFF switch and
try to start the machine.
Figure-13 Disabling key
If the machine starts, immediately stop the
machine. The switch disabling feature is not
working on your machine and it should be
fixed.
If the machine does not start, the switch
disabling key is working.
WARNING!
Before starting the machine, make sure
that you have read and understood the
user manual and you are familiar with the
safety features of the machine. Failure to
do so may cause serious personal injury.

11
OPERATION
Operating the CX424 dust collector is very
simple and straightforward.
Make sure the dust collector is properly
assembled and worked during the test run.
Move the CX424 close to the machine and
use a proper sized hose connecting the
hose with its one end to the machine and
the other end to the dust collector.
Make sure the connections are secured
using hose clamps and connect the ducting
ground and the dust collector is ready for
operation.
MAINTENANCE
Maintenance on this machine is fairly simple.
Each time you use your dust collector, make
sure to properly clean the bags and take a
quick inventory of your machines
performance. Check the dust collector
regularly for loose bolts, screws, ensure the
dust collection bag has no tears, and ensure
all wires are in good condition.
BAG CLEANING
Empty the collection bag on a regular basis.
The machine will run more efficiently if the
collecting bag is emptied regularly.
Make sure the switch is in the OFF position
and the cord is disconnected from the
power source.
Make sure you are wearing a respirator or
dust mask while emptying the collection
bag. The tiny dust particles in the air can be
inhaled easily and can be hazardoos
injurious to your health.
Uninstall the clamp securing the collection
bag around the collector ring. Remove the
collection bag and empty it.
Re-install the bag and clamp it.
CLEANING THE CANISTER
(If using a canister)
The canister has a cleaning handle which
allows for easy cleaning of the canister by
simply rotating the handle. After each use,
rotate the handle at least one full turn. The
fingers inside the canister will knock most of
the dust into the lower collection bag.
Make sure not to clean the canister using
water or compressed air which can damage
the filtration pleats of the filter. Always use
the cleaning handle.
LUBRICATION
CX424 comes equipped with shielded
bearings which are permanently lubricated.
So, there is not need to lubricate them.
WARNING!
Do not use the CX424 for any other
operation other than collecting sawdust.
Failure to do so could result in
malfunction of the machine and may
void the warranty.
WARNING!
Do not make any adjustments while the
machine is running. Turn off the
machine and un-plug from the power
source before making any adjustments.

12

13

14

15
WARRANTY
Craftex warrants every product to be free from defects in materials and agrees to correct such defects
where applicable. This warranty covers three years for parts and 90 days for labour (unless specified
otherwise), to the original purchaser from the date of purchase but does not apply to malfunctions
arising directly or indirectly from misuse, abuse, improper installation or assembly, negligence,
accidents, repairs or alterations or lack of maintenance.
Proof of purchase is necessary
All warranty claims are subject to inspection of such products or part thereof and Craftex reserves the
right to inspect any returned item before a refund or replacement may be issued. Return authorization
may take up to 72 hours for inspection and approval.
This warranty shall not apply to consumable products such as blades, bits, belts, cutters, chisels,
punches etceteras.
Craftex shall in no event be liable for injuries, accidental or otherwise, death to persons or damage to
property or for incidental contingent, special or consequential damages arising from the use of our
products.
RETURNS, REPAIRS AND REPLACEMENTS
To return, repair, or replace a Craftex product, you must visit the appropriate Busy Bee Tools
showroom or call 1-800-461-BUSY. Craftex is a brand of equipment that is exclusive to Busy Bee
Tools.
For replacement parts directly from Busy Bee Tools, for this machine, please call 1-800-461-BUSY
(2879), and have your credit card and part number handy.
All returned merchandise will be subject to a minimum charge of 15% for re-stocking and handling
with the following qualifications.
Returns must be pre-authorized by us in writing.
We do not accept collect shipments.
Items returned for warranty purposes must be insured and shipped pre-paid to the nearest
warehouse
Returns must be accompanied with a copy of your original invoice as proof of purchase. Returns
must be in an un-used condition and shipped in their original packaging a letter explaining your
reason for the return. Incurred shipping and handling charges are not refundable.
Busy Bee will repair or replace the item at our discretion and subject to our inspection.
Repaired or replaced items will be returned to you pre-paid by our choice of carriers.
Busy Bee reserves the right to refuse reimbursement or repairs or replacement if a third party
without our prior authorization has carried out repairs to the item.
Repairs made by Busy Bee are warranted for 30 days on parts and labour.
Any unforeseen repair charges will be reported to you for acceptance prior to making the repairs.
The Busy Bee Parts & Service Departments are fully equipped to do repairs on all products purchased from
us with the exception of some products that require the return to their authorized repair depots. A Busy Bee
representative will provide you with the necessary information to have this done.
CRAFTEX 3 YEAR LIMITED WARRANTY

16