Craftsman 315.SS630 User manual

MANUAL DEL OPERADOR
®
19.2 VOLT PAreNT
SPRAYER TOOL
HERRAMIENTA ROCIADORA
DE PINTURA DE 19,2 V
Model No.
315.SS630
N0mero de modelo
315.SS630
WARNING: To reduce the risk
of injury, the user must read and
understand the operator's manuaU
before using this product.
ADVERTENCJA: Para reducir eU
nesgo de Uesiones, eUusuano debe Ueer
y comprender eUmanuaU deUoperador
antes de usar este producto.
Customer Help Line: 1-800-932-3188
TeU6fonode atenci6n aUconsumidor: 1-800-932-3188
BATTERIES AND CHARGERS
SOLD SEPARATELY
LAS BATI=RIAS Y LOS CARGADORES
SE VENDEN POR SEPARADO
Sears Brands Management, 3333 Beverly Rd., Hoffman Estates, IL 60179 USA
Visit the Craftsman _ web page: www.sears.com/craftsman
Visite el sitio web de Craftsman'S>:www.sears.com/craftsman
987000-915
8-5-11 (REV:04)
Save this manual for future reference
Guarde este manual para futuras consumta

Warranty.......................................................................2
introduction..................................................................2
importantSafetyinstructions.......................................3
SpecificSafetyRuUes.................................................4-5
SymboUs........................................................................6
Features........................................................................7
AssembUy......................................................................7
Operation...................................................................8-9
Maintenance...............................................................10
Troubleshooting..........................................................11
IHustratedPartsList....................................................12
FigureNumbers(HUustrations).....................................iqi
PartsOrdering/Service..................................BackPage
Garant[a........................................................................2
Introducci6n..................................................................2
Instruccionesdesegundadimportantes......................3
RegUasdesegundadespecificas...............................4-5
S[mboUos.......................................................................6
Caracteristicas..............................................................7
Armado.........................................................................7
Funcionamiento.........................................................8-9
Mantenimiento............................................................10
Correcci6ndeprobUemas...........................................11
Figuranumeras(ilustraciones).....................................iqi
Pedidosdepiezas/Servicio .................... p_g. posterior
CRAFTSMAN ®ONE YEAR LiMiTED WARRANTY
FOR ONE YEAR from the date of purchase, this product is warranted against any defects in material or workmanship.
With proof of purchase, defective product will be replaced free of charge.
For warranty coverage detaiJs to obtain free replacement, visit the web site: www, craftsman,com
This warranty does not cover the atomizer valves, the cleaning brush or the lubricant, which are expendable parts that
can wear out from normal use within the warranty period.
This warranty is void if this product is ever used while providing commercial services or if rented to another person.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, mL60179
GARANTiA LIMmTADA DE CRAFTSMAN POR UN ANO
Este producto tiene garant[a por cualquier defecto en material o mano de obra DURANTE UN ArgO desde la fecha de
compra. Los productos defectuosos se remplazar_n sin cargo si presenta un comprobante de pago.
Si desea conocer los detalles de la cobertura de la garantia para conseguir reparaciones o recambios, visite el
sitio Web: www.craftsman.com
Esta garantia no cubre la v_lvulas atomizadoras, la cepillo para limpiar o la lubricante, que es una pieza fungible que
puede desgastarse por el uso normal durante el periodo de garant[a.
La garantia pierde validez si este producto se utiliza mientras se prestan servicios comerciales o si se alquila a otra
persona.
Esta garant[a le otorga derechos legales especificos y tambi6n puede gozar de otros derechos que varian segOn el
estado.
Sears Brands Management Corporation, Hoffman Estates, mL60179
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
Esta producto ofrece numerosas caracteristicas para hacer mas agradable y placentero su uso. En el diseSo de este
producto se ha conferido prioridad a la seguridad, el desempeSo y la fiabilidad, por Io cual se facilita su manejo y
mantenimiento. 2

_ WARNING:SAVETHESEINSTRUCTmONS.To
reducetherisksoffireorexpbsion,eUectricshock,
andtheinjuryto persons,readandunderstandaH
instructionsincludedinthismanualBefamiUiarwith
thecontroUsandtheproperusageoftheequipment.
READ ALL mNSTRUCTmONS
KNOW YOUR POWER TOOL. Read the operator's
manuaU carefully. Learn the machine's appUications and
Uimitationsas well as the specific potentiaUhazards reUated
to this tooL
WAF{NING: To reduce the risk of fire or expbsion:
Do not spray fiammabUe or combustibUe matedaUs
near an open flame or sources of ignition such as
cigarettes, motors, and electrical equipment.
For units intended for use with only water-based or
mineral spirit-type materials with a minimum flash
point of 140°F (60°C), do not spray or clean with
liquids having a flash point less than 140°F (60°C).
Paint or solvent flowing through the equipment is
able to result in static electricity. Static electricity
creates a risk of fire or explosion in the presence of
paint or solvent fumes.
Do not use a paint or a solvent containing haloge-
nated hydrocarbons.
Keep spray area well ventilated. Keep a good supply
of fresh air moving through the area. Keep pump
assembly in a welPventilated area.
Do not smoke in the spray area.
Do not operate light switches, engines, or similar
spark-producing products in the spray area.
Keep area clean and free of paint or solvent contain-
ers, rags, and other flammable materials.
Know the contents of the paints and solvents being
sprayed. Read all Material Safety Data Sheets
(MSDS) and container labels provided with the
paints and solvents. Follow the paint and solvent
manufacturer's safety instructions.
Fire extinguisher equipment shall be present and
working.
WARNING: To reduce the risk of skin injection:
Do not aim the nozzle at, or spray any person or
animal.
Keep hands and other body parts away from the
discharge. For example, do not try to stop leaks
with any part of the body.
Always use the spray tip. Do not spray without spray
tip in place.
Only use a spray tip specified by the manufacturer.
Use caution when cleaning and changing spray tips.
in the case where the spray tip clogs while spraying,
follow the manufacturer's instructions for turning off
the unit before removing the spray tip to clean.
Do not leave the unit energized while unattended.
When the unit is not in use, turn off the unit in
accordance with the manufacturer's instructions.
High pressure spray is able to inject toxins into the
body and cause serious bodily injury. In the event
that injection occurs, seek medical attention imme-
diately.
Check parts for signs of damage. Replace any dam-
aged parts.
This system is capable of producing 2500 psi. Only
use replacement parts or accessories that are speci-
fied by the manufacturer and that are rated a mini-
mum of 2500 psi.
Know how to stop the unit quickly. Be thoroughly
familiar with the controls.
Verify that all connections are secure before operat-
ing this unit.
For household use only.
WARNING: To reduce the risk of injury:
Do not operate or spray near children. Keep children
away from equipment at all times.
Do not overreach or stand on an unstable support.
Keep effective footing and balance at all times.
Stay alert and watch what you are doing.
Do not operate the unit when fatigued or under the
influence of drugs or alcohol.
3 - English

Keepguardsinplaceandinworkingorder.Never
operatethetooUwithanyguardorcoverremoved.
MakesureaHguardsareoperatingpropertybefore
eachuse.
Toreducetheriskofinjury,keepchildrenandvisitors
away.Allvisitorsshouldwearsafetyglassesandbe
keptasafedistancefromworkarea.
Keeptheareaofoperationc_earofallpersons,
particularlysmallchildren,andpets.
UserighttookDon'tforcetoolorattachmenttodoa
jobitwasnotdesignedfor.Don'tuseitforapurpose
notintended.
Donotoperatetheequipmentwhilebarefoot
orwhenwearingsandalsorsimilarlightweight
footwear.Wearprotectivefootwearthatwillprotect
yourfeetandimproveyourfootingonslippery
surfaces.
ExercisecautiontoavoidsJippingorfalling.
AlwaysweareyeprotectionwithsidesHe_ds
markedto compJywithANSiZ87.1.Followingthis
rulewillreducetheriskofseriouspersonalinjury.
UseonJyrecommendedaccessories.Theuseof
improperaccessoriesmaycauseriskofinjury.
FoJlowthemaintenanceinstructionsspecifiedin
thismanual.
Checkdamagedparts.Beforefurtheruseofthe
tool,aguardorotherpartthatisdamagedshould
becarefullycheckedtodeterminethatitwilloperate
properlyandperformitsintendedfunction.Checkfor
alignmentofmovingparts,bindingofmovingparts,
breakageofparts,mounting,andanyotherconditions
thatmayaffectitsoperation.Aguardorotherpartthat
isdamagedmustbeproperlyrepairedorreplacedby
anauthorizedservicecenterto avoidriskofpersonal
injury.
NeverleavetooJrunningunattended.Turnpower
off.Don'tleavetooluntilitcomestoacompletestop.
BethoroughlyfamiJiarwith controls.Knowhowto
stoptheproductandbleedpressurequickly.
Keeptooldry,dean,andfreefromoilandgrease.
Alwaysuseacleanclothwhencleaning.Neveruse
brakefluids,gasoline,petroleum-basedproducts,or
anysolventstocleantool.
Donot usetool ifswitchdoesnotturnit off.Have
defectiveswitchesreplacedbyanauthorizedservice
center.
Beforec_eaning,repairing,orinspecting,shutoffthe
motorandmakecertainallmovingpartshavestopped.
Avoiddangerousenvironment.Don'tuseindampor
wetlocationsorexposetorain.Keepworkareawelllit.
NeverdirectapaintstreamtowardpeopJeor pets,
oranyeJectricaldevice.
Neverstartthemachineificehasformedinanypart
oftheequipment.
WARNING:Highpressurespraycanbedangerous
ifsubjectto misuse.Thespraymustnotbedirected
atpersons,animals,electricaldevices,orthemachine
itself.
Keepawayfromhotparts.
Checkboltsandnutsforloosenessbeforeeachuse.
Alooseboltornutmaycauseseriousmotorproblems.
Beforestoring,allowtheproductto cook
StoreinacooJ,weH-ventiJatedarea,safelyaway
fromsparkand/orflame-producingequipment.
WhenservicinguseonJyidenticalreplacement
parts.Useofanyotherpartsmaycreateahazardor
causeproductdamage.
Neverusethesprayerwithoutaspraytipinstalled.
Aninjectioninjurycanleadto possibleamputation.
Seeaphysicianimmediately.
Neverputyourhandinfrontofthespraytipwhenin
use.Gloveswillnotalwaysprovideprotectionagainst
aninjectioninjury.
Wearclothingto keeppaintoffskinandhair,
alongwithamaskorrespiratorduringuse.Paints,
solvents,andothermaterialscanbeharmfulifinhaled
oriftheycomeintocontactwiththebody.
AJwaysshutthe unit off,removethe batterypack,
andreJeasepressurebeforeservicing,cleaningthe
tiporguard,changingthetip,orleavingunattended.
Plasticcancausesparks.Neverhangplasticto
encloseasprayarea.Donotuseplasticdropcloths
whensprayingflammablematerials.
Donotsprayoutdoorsonwindydays.
Donotattemptto deanorunclogthespraytipwith
yourfinger.
AbatteryoperatedtooJwith integralbatteriesora
separatebatterypackmustberechargedonlywith
thespecifiedchargerfor thebattery.Achargerthat
maybesuitableforonetypeofbatterymaycreatea
riskoffirewhenusedwithanotherbattery.
Usebatteryoperatedtool onlywithspecifically
designatedbatterypack.Useofanyotherbatteries
maycreateariskoffire.
Usebatteryonlywith chargerlisted.Forusewith
19.2Vnickel-cadmiumand19.2VJithiumoionbattery
packs,seetool/appliance/batterypacWcharger
correlationsupplement988000-272.
4- English

Disconnectbatterypackfromtool beforemaking
anyadjustments, changing accessories, or storing
the tool. Such preventive safety measures reduce the
risk of starting the tooUaccidentally.
When battery pack is not in use, keep it away from
other metal objects mike:paper dips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminaUs together may cause
sparks, burns, or a fire.
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possibJe hazards
when not using your battery tool or when changing
accessories. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
Do not place battery tools or their batteries near
fire or heat. This will reduce the risk of explosion and
possibly injury.
Do not crush, drop or damage battery pack. Do
not use a battery pack or charger that has been
dropped or received a sharp bJow. A damaged
battery is subject to explosion. Properly dispose of a
dropped or damaged battery immediately.
Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery
can propel debris and chemicals, if exposed, flush with
water immediately.
Do not charge battery tooJ in a damp or wet
mocation. Following this rule will reduce the risk of
electric shock.
For best results, your battery tool should be charged
in a location where the temperature is more than
50°F but less than 100°R Do not store outside or in
vehicles.
Under extreme usage or temperature conditions,
battery aeakage may occur, ff liquid comes in
contact with your skin, wash immediately with soap
and water, mfliquid gets into your eyes, flush them
with dean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
Never leave a tool unattended with the battery
installed.
Save these instructions. Refer to them frequently and
use them to instruct other users. If you loan someone
this tool, loan them these instructions also.
CALIFORNIA PROPOSITION 65
_ WARNING: This product, and the paints designed to be applied with this product, may contain chemicals,
including lead, known to the State of California to cause cancer, birth defects, or other reproductive harm. Wash
hands after handling.
Some examples of these chemicals are:
o lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
5 =English

ThefollowingsignaUwordsandmeaningsareintendedtoexpUaintheUeveUsofriskassociatedwiththisproduct.
SYMBOL SmGNAL MEANmNG
indicatesanimminentlyhazardoussituation,which,ifnotavoided,willresuUt
indeathorseriousinjury.
indicatesapotentiallyhazardoussituation,which,ifnotavoided,couUdresuUt
WARNING: indeathorseriousinjury.
indicatesapotentiallyhazardoussituation,which,ifnotavoided,mayresult
CAUTmON: in minor or moderate injury.
CAUTION: (Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert
Read Operator's Manual
Eye Protection
Recycle Symbols
indicates a potential personal injury hazard.
To reduce the risk of injury, user must read and understand
operator's manual before using this product.
Always use eye protection with side shields marked to comply
with ANSI Z87.1.
This product uses nickel-cadmium (Ni-Cd) and lithium-ion
(Li-ion) batteries. Local, state, or federal laws may prohibit
disposal of batteries in ordinary trash. Consult your local waste
authority for information regarding available recycling and/or
disposal options.
V Volts Voltage
Direct Current Type or a characteristic of current
PSI Pressure Pressure is measured in pounds per square inch
Flow rate is measured in maximum gallons of paint sprayed per
GPH Flow Rate hour
6 - English

PRODUCT SPECIFICATmONS
Container Size ................................................................................................................................................................... 1 qt.
Motor .................................................................................................................................................................... 19.2 Volt DC
KNOW YOUR PAINT SPRAYER
See Figure 1, page L
The safe use of this product requires an understanding
of the information on the product and in this operator's
manual as well as a knowledge of the project you are
attempting. Before use of this product, familiarize yourself
with aHHoperating features and safety ruHes.
C3 ENERGY iNDiCATOR WINDOW
The C3 energy indicator wdndow located on the side of the
handle will light when a Craftsman! 9.2 V compact lithium-
ion battery pack (315.113710) is installed and has charge.
NOTE: Feature wiHHnot Hightwith Craftsman 19.2 V nickeH-
cadmium battery packs.
mNNOVATiVL= MOTOR DESIGN
The innovative motor design means less vibration and
noise when using your sprayer.
QUICK-LOCK CONTAINER
The quick-Hock feature aHHowseasy instaHHationand
removal of the paint container.
SPRAY TraPS
The two spray tips provided allow you to choose between
different spray patterns - vertical, horizontal, and round.
UNPACKING
This product has been shipped completely assembled.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing
list are included.
_ WARNING: Do not use this product if it is not
completely assembled or if any parts appear to be
missing or damaged. Use of a product that is not
properly and completely assembled could result in
serious personal injury.
inspect the product carefuHHyto make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product.
if any parts are damaged or missing, pHeasecaHH
1-800-932-3188 for assistance.
PACKING LIST
Paint Sprayer with Quick-Lock Container and Wide Fan Tip
Replacement Atomizer Valve
Brush CHeaner
Lubricant
Round Tip
Operator's Manual
_ WARNING: if any parts are damaged or missing do
not operate this product untiHthe parts are repHaced.
Use of this product with damaged or missing parts
could result in serious personal injury.
WARNING: Do not attempt to modify this product
or create accessories not recommended for use with
this product. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
WARNING: To prevent accidental starting that
could cause serious personal injury, always remove
the battery pack from the product when assembling
parts.
7 - EngHish

WARNING:DonotallowfamiUiadtywithproducts
to makeyoucareUess.RememberthatacareUess
fractionofasecondissufficienttoinflictserious
injury.
WARNING:AUwaysweareyeprotectionwithside
shbUdsmarkedtocompUywithANSiZ87.1.FaiUure
to dosocouUdresuUtinfluidsenteringyoureyes
resuUtinginpossibUeseriousinjury.
WARNING:Donotuseanyattachmentsor
accessoriesnotrecommendedbythemanufacturer
ofthisproduct.Theuseofattachmentsor
accessoriesnotrecommendedcanresuUtinserious
personaUinjury.
APPLICATmONS
You may use this product for the purposes Uistedbebw:
interior and exterior painting and staining of decks,
outdoor furniture, fences, and walls
This product will accept Craftsman _>19.2 V lithium-ion
battery packs and Craftsman _>19.2 V nickePcadmium
battery packs.
For complete charging instructions, refer to the Operator's
Manual for the battery packs and chargers listed in the
Specific Safety instructions.
8ATTI=RY PROT_=CTmON FI=ATURI=S
Craftsman _ 19.2 V lithium-ion battery packs are designed
with features that protect the lithiumqon cells and
maximize battery life.
if the tool stops during use, release the trigger to reset
and resume operation. _fthe tool still does not work, the
battery needs to be recharged.
TO mNSTALL /REMOVE BATTERY PACK
See Figure 2, page L
_ WARNING: Always remove battery pack from
your tool when you are assembling parts, making
adjustments, cleaning, or when not in use. Removing
battery pack will prevent accidental starting that
could cause serious personal injury.
To install:
Place the battery pack in the tool. Align the raised rib
on the battery pack with groove in the battery port.
Make sure the latches on each side of the battery pack
snap in place and that the battery pack is secured in
the tool before beginning operation.
To remove:
Depress the latches on both sides of the battery pack
to release the battery pack and remove it from the tool.
_ WARNING: Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
_1_ WARNING: Risk of fire or explosion. Spray area
must be welPventilated and away from sparks or
flames.
FiLLiNG SPRAYER WiTH PAiNT/STAIN
See Figure 3 =4, page L
Remove and discard any skin that has formed on top of
the paint or stain, then thoroughly mix the material in its
original container before beginning.
NOTE: Older containers of stain and paint may need to be
strained before use.
Remove the battery pack from the sprayer.
Remove the quick-lock container by twisting counter-
clockwise so that the arrow on the container lines up
with the "unlock" symbol on the lid.
Fill the container with paint or stain as desired. Do not
fill above the max fill mark on the container.
Reinstall the container on the sprayer and twist
clockwise so that the arrow on the container lines up
with the "lock" symbol on the lid.
SELECTING THE PROPER SPRAY Trap
See Figure 5, page iL
Use the round tip for latex paints, oil-based paints,
and stains. This tip sprays in a round pattern.
To
Use the wide fan tip for latex paints. This tip
sprays in a wide pattern that can be adjusted from
horizontal to vertical.
switch tips:
Remove the battery pack from the sprayer.
Remove the installed tip by turning it counter-clockwise.
Install the desired tip and rotate clockwise to tighten
securely.
NOTE: The tip should be tightened securely by hand. A
too loose or overtightened tip may cause the sprayer to
leak or be damaged.
8 - English

Tochangedirectionoffantip:
Slightlyloosenthefantipbyrotatingcounter-clockwise
1/4turn.
Rotatetheadjustingarm1/4turninthedirection
neededtoswitchthedirectionofthetipspray.
Whileholdingtheadjustingarminposition,rotatethe
widefantipclockwiseuntilsecurelytightened.
_ WARNING:Toreducetheriskofinjection,donot
pointsprayeratanypartofthebodyorperson.
incaseofskininjection,seekmedicalattention
immediately.Donotusewithoutspraytipinplace.
OPERATING THE SPRAYER
See Figures 6 -9, page iL
Place a line of lubricant on the piston. To gain access to
the piston, follow the instructions in Cleaning the Sprayer
for Storage in the Maintenance section of this manual.
Ensure surface to be painted is free of dust, dirt, and
grease.
Mask or cover any areas not intended to be painted or
stained. Be aware of wind that may cause your paint
or stain to spray into areas not desired. Always use
drop cloths or other cover to protect areas that are not
intended to be painted or stained.
Fill the quickqock container with no more than 1 quart
of desired paint or stain.
NOTE: After every 4 refills of the quickqock container,
add a line of lubricant to the piston. See Cleaning the
Sprayer for Storage for instructions on disassembling
the sprayer to gain access to the piston.
Select the proper spray tip for desired spray pattern.
Install the battery pack in the sprayer.
Pull the switch trigger to spray paint. Release the
switch trigger to stop paint spray.
Practice spraying on a piece of scrap material to test
your spray pattern and to prime the pump before
beginning. If you do not get a preferred spray pattern
with an even amount of paint or stain throughout,
paint may be thinned as desired. Refer to the
Troubleshooting section later in this manual.
NOTE: The pump must be primed after every paint
change and at first use after storing. Spray paint at a
scrap surface for at least 20 seconds to prime.
To create an even coating over the entire surface:
o Move your arm at a steady rate of speed and make
sure to move your entire arm, not just your wrist.
Keep the sprayer an even distance from the area
being sprayed, which should be between 18 to 20
inches from the tip of the sprayer to the surface
being sprayed.
Depress the trigger to begin the spray off the mate-
rial you want to paint. Operate the sprayer in straight
horizontal or vertical strokes across the surface
being painted, then release the trigger off the mate-
rial to end the stroke.
NOTE: For spray quality consistency when using
thinner paints, it may be necessary to keep the trig-
ger depressed between strokes.
When finished, remove the battery pack, return any
unused paint or stain to its original container, and
thoroughly clean the sprayer.
CAUllON: It is important to thoroughly clean the
sprayer after each use or when changing colors.
Allowing paint or stain to remain in an idle tool for an
extended period can cause its moving pieces to seize up.
_ WAF{NING: Do not clean with any flammable liquids
such as paint stripper, paint remover, brush cleaner,
mineral spirits, lacquer thinner, turpentine, acetone,
gasoline, kerosene, etc.
CLEANING THE SPRAYER AFTER USE
The solution used to clean the sprayer is determined
by the type of material that has been sprayed. For
anything other than latex material, follow the material
manufacturer's directions for appropriate clean-up.
To clean the sprayer for short term storage:
Remove the battery pack from the sprayer.
if you haven't already done so, remove the paint
container and return any unused paint or stain to its
original container.
Fill the paint container with lukewarm water (following
the use of latex products) or any non-flammable paint
thinner (following the use of oiPbased products).
Reinstall the paint container.
Install the battery pack in the sprayer.
Spray the solution onto a piece of cardboard or other scrap
material. Continue spraying until all the solution is used.
Remove the battery pack from the sprayer.
Place a line of lubricant on the piston. To gain access to
the piston, follow the instructions in Cleaning the Sprayer
for Storage in the Maintenance section of this manual.
Use a damp cloth to wipe the exterior of the sprayer.
The unit is now ready to put away.
9 - English

WARNING:Whenservicing,useonlyidentical
replacementparts.Useofanyotherpartsmay
createahazardorcauseproductdamage.
WARNING:Alwaysweareyeprotectionwithside
shieldsmarkedtocomplywithANSIZ87.1.Failure
to dosocouldresultinfluidsenteringyoureyes
resultinginpossibleseriousinjury.
MAINTENANCE PROCEDURES
NOTE: Always remove the battery pack from the unit
before attempting a service operation.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
_ WARNING: Do not at any time let brake fluids,
gasoline, penetrating oils, etc., come in contact with
plastic parts. Chemicals can damage, weaken, or
destroy plastic which may result in serious personal
injury.
CLEANING THE SPRAYER FOR STORAGE
See Figure 8, page iL
When you've finished your project and are ready to
store the sprayer, a thorough cleaning and Uubfication is
recommended.
Remove the battery pack from the sprayer.
Remove the paint container.
if you haven't aUreadydone so, return any unused paint
or stain to its originaUcontainer.
Fill the paint container with Uukewarm water (following
the use of Uatexproducts) or any non-fiammabUe paint
thinner (following the use of oiPbased products).
Reinstall the paint container.
install the battery pack in the sprayer.
Spray the solution onto a piece of cardboard or other
scrap material. Continue spraying until all the solution
is used.
Remove the battery pack from the sprayer.
Remove the paint container.
Remove the suction tube and filter.
Remove the installed spray tip by turning it
counterclockwise.
Remove the atomizer valve assembly.
Remove the locking nut by turning it counterclockwise.
Slide the pump housing assembly/container lid forward
off the sprayer.
Pull the piston and spring off the pump housing.
Using the cleaning brush provided and the solution
determined by the last type of paint or stain sprayed,
clean all of the above parts thoroughly.
NOTE: Make sure to scrub thoroughly inside the pump
housing opening so that no paint or stain material is left
behind.
Clean the vent hob in the pump housing using a
straightened paper clip.
To reassembJe:
Place a line of lubricant on the piston.
Slide the spring back onto the piston.
insert the piston and spring assembly inside the back
of the pump housing.
Replace the pump housing assembly/container lid onto
the sprayer.
Replace the locking nut on the motor housing by
pushing in while rotating clockwise to secure.
insert the atomizer valve assembly into the pump
housing front opening.
Replace the spray tip and rotate clockwise to secure.
Reinstall the suction tube and filter.
Reinstall the paint container.
The sprayer is now ready to be stored.
REPLACING ATOMIZER VALVE ASSEMBLY
See Figure 10, page ft.
The atomizer valve causes the paint or stain material to
spin as it comes out of the sprayer. After 7 to 10 gallons of
paint or stain, the atomizer valve may no longer produce a
good spray pattern and may need to be replaced.
To repJace:
Remove the battery pack from the sprayer.
Rotate the spray tip counterclockwise and remove.
install the new atomizer valve assembly
Replace the spray tip and rotate clockwise to secure.
BATTERY PACK RPMOVAL AND
PREPARATION FOR RECYCLING
_ WARNING: Upon removal, cover the battery
pack's terminals with heavy-duty adhesive tape.
Do not attempt to destroy or disassemble battery
pack or remove any of its components. Lithium-ion
and nickePcadmium batteries must be recycled
or disposed of properly. Also, never touch both
terminals with metal objects and/or body parts as
short circuit may result. Keep away from children.
Failure to comply with these warnings could result in
fire and/or serious injury.
10 - English

Motordoesnotrun.
Motoroverheats.
MotorhasaUowhumbutdoesnot
spray.
Motorseemsto berunningproperty
butdoesn'tspray.
SprayedmateriaUisspitting,gUobbing
uporunabUeto getapreferredspray
patternwithanevenamountofpaint
orstain
CAUSE
Battery is not charged.
Piston has seized up.
Continuous spray operation.
Piston has seized up.
Suction tube and fluter are Uooseor
damaged.
Atomizer vaUveis cUogged or worn
out.
MateriaUbeing sprayed is too thick.
PUuggedspray tip or intake fluter;
worn piston.
Paint container voUume is getting Uow.
MateriaUbeing sprayed is too thick.
Suction tube is Uoose.
Atomizer vaUveis cUogged or worn
out.
POSSIBLE SOLUTmON
Charge battery.
ThoroughUy cUeanthe sprayer using long-
term storage cleaning instructions in the
Maintenance section of this manual.
Release trigger at the end of each pass
to allow the motor to cool.
Thoroughly clean the sprayer using long-
term storage cleaning instructions in
the Maintenance section of this manual.
Reinstall or replace suction tube and
filter as needed.
Clean or replace atomizer valve.
Follow material manufacturer's direc-
tions and thin material as needed.
Thoroughly clean the sprayer and, if
necessary, replace piston*, using stor-
age cleaning instructions in the Mainte-
nance section of this manual.
Refill paint container.
Follow material manufacturer's direc-
tions to thin material as needed.
Reinstall suction tube securely.
Clean or replace atomizer valve.
Worn spray tip or piston. Clean or replace spray tip or piston*.
Paint/stain spray overspray is exces- Spray tip is too far from the surface Hold sprayer closer to the surface being
sive. being sprayed, sprayed.
Paint/stain runs or sags on the work Proper paint methods not being Refer to Operating the Sprayer earlier
surface, observed, in this manual.
Paint/stain is leaking behind the Spray tip is loose. Tighten spray tip.
spray tip. Atomizer valve is worn or not posi- Replace or reposition atomizer valve as
tioned properly, needed.
*Although unlikely, a worn piston is possible. A replacement piston can be purchased by cafling customer service at
1-800-932-3188. Follow the instructions in Cleaning the Sprayer for Storage to access the piston for replacemenL
11 - English

CRAFTSMAN PAINT SPRAYER - MODEL NUMBER 315.SS630
I The modemnumber wiHHbe found on a HabeHattached to the motor housing. Always mention the model |
number in aHHcorrespondence regarding your paint sprayer or when ordering repair parts. J
SEE BACK PAGE FOR PARTS ORDERING iNSTRUCTiONS
9
8 7
12
Key Part
No. Number
1 940114264
2 940207025
3 303233002
4 692331001
5 303221001
6 519459001
7 303265001
8 303262002
9 303260002
10 303263001
11 303836001
12 521206001
987000915
PARTS LiST
Description Qty,
Logo LabeH...................................................................................................... 1
Data LabeH....................................................................................................... 1
Piston AssembHy .............................................................................................. 1
Spring .............................................................................................................. 1
Pump Housing AssembHy ................................................................................ 1
Locking Nut ..................................................................................................... 1
Atomizer Valve AssembHy ................................................................................ 1
Round Tip ........................................................................................................ 1
Wide Fan Tip ................................................................................................... 1
CHeaning Brush ................................................................................................ 1
Suction Tube and FiHter................................................................................... 1
Quick-Lock Container ..................................................................................... 1
Operator's Manual (960931508)
12 =EngHish

B
A o1 qt. quickolockcontainer [contenedor de
aseguramientor@ido de0,9464 1(1 cto.)]
B oWidefan tip [punta anchaenabanico]
Co1 in. roundfan tip [punta redonda enabanico
de25,4 mm (1 pulg.)]
DoLubricant bottle (botellade lubricant@
EoSwitchtrigger (gatillo delinterruptor)
F oCleaningbrush (cepillo paralimpiar)
GoReplacementatomizervalveassembly
(reemplazodelconjunto dela valvula
atomizadora)
B
AoBatterypack (paquetede baterias)
Bo Depresslatchesto releasebattery pack(para
soltar, el paquetede bateriasoptima los
pestillos)
AoLock (asegurar)
BoUnlock(desasegurar)
AoMaxfill line (lineadeIlenadomaxim@
B - 1/2 quart fill line (lineade Ilenadode1/2
cuarto)

A
A- Rotatespraytip counterclockwiseto loosen
(gire la puntade rociado a la izquierdapara
aflojarla)
B- Rotateadjusting arm 1/4 turn to change
direction of paint sprayfrom horizontalto
vertical (gire el brazodea)uste1/4 de vuelta
paracambiar la direccion derociado de la
pinturade horizontala vertical)
C- Verticalspraydirection (direccion derociado
vertical)
D° Horizontalspray direction (direccion de
rociado horizontal)
CORRECTSPRAYTECHN)QUE
(TECN(CADE ROC(ADO(;OF{RECTA)
_mm(
(NCORRECTSPRAYTECHNIQUE
(TECN(CADE ROC(ADO(NCORRECTA)
i ii ili! ! iii i,iiiiiiii'iiii iii iiiiiiii,i, iiiii i i , , ,
AoSpraytip (puntade rociado)
BoAtomizervalveassembly(conjunto de
valvulaatomizadora)
CoLockingnut (tuercadeseguridad)
D° Pumphousing assembly/containerlid
(conjunto dealojamiento dela bomba/tapa
del contenedor)
EoSpring (resorte)
Fo Piston (pist6n)
GoSprayer housing (alojamientodelrociador)
H° Quick-lock container (contenedorde
aseguramientorapido)
I ° Suction tubeand filter (tubo de succion y
filtro)
PLACEUNE OFLUBR(CANT
ON P(STONSHAFT
PLACERUNEPELL(CULEBELUBR)F(ANTSUR
L'ARBREDE P)STON)
A ° Atomizervalveis good (la %lvula
atomizadoraest_en buenestado)
B- Atomizervalveis bad and needsto be
replaced(lav_lvula atomizadoraest_enmal
estadoy necesitaset reemplazada)

,_ ADVERTENCIA: GUARDE ESTAS
mNSTRUCCmONES°Para reducir el nesgo de
incendio o explosiSn, descanga el6ctdca, y la
lesiones a personas, lea y comprenda todas
instrucciones incluidas en este manual. Familiar[cese
con todos los controles y la forma correcta de utilizar
la equipo.
LEA TODAS LAS mNSTRUCCIONES
FAMmLmARiCESE CON SU HERRAMmENTA
ELECTRmCA. Lea cuidadosamente el manual del
operador. Aprenda sus usos y limitaciones, as[ como
los posibles peligros espec[ficos de esta herramienta.
ADVERTENCIA: Para reducir el nesgo de estallido o
explosi6n:
[] No rode materiales infiamables ni combustibles
cerca de llamas abiertas o fuentes de igniciOn,
como cigarrillos, motores y equipos el6ctricos.
[] No rode ni limpie con I[quidos que tengan un punto
de inflamaciOn menor a 60 °C (! 40 °F) las unidades
diseSadas para ser utilizadas s61o con materiales a
base de agua o de un tipo de alcohol mineral con un
punto de inflamaci6n m[nimo de 60 °C (!40°F).
[] La pintura o el solvente que fiuyen a trav6s del
equipo pueden generar electricidad est_tica. La
electricidad est_tica produce un riesgo de incendio
o explosi6n en presencia de emanaciones de
pintura o de solvente.
[] No use una pintura o un solvente que contenga
hidrocarburos halogenados.
[] Mantenga el _rea de rociado bien ventilada.
Mantenga una buena circulaciOn de aire fresco en el
_rea. Mantenga el conjunto de la bomba en un _rea
bien ventilada.
[] No fume en el _rea donde se _rea de rociado.
[] No utilice interruptores de luz, motores o productos
similares que produzcan chispas en el _rea donde
se Area de rociado.
[] Mantenga el _rea limpia y sin contenedores de
pintura o solvente, trapos y otros materiales
inflamables.
[] Conozca el contenido de las pinturas y los solventes
que se roc[an. Lea todas las hojas de datos sobre la
seguridad de materiales (MSDS) y las etiquetas de
los contendores que se proveen con las pinturas y
los solventes. Siga las instrucciones de seguridad
del fabricante de la pintura y el solvente.
[] Tenga a mano un extinguidor de incendios que
funcione.
ADVERTENCIA: Para reducir el riesgo de inyecci6n:
[] No apunte la boquilla ni rode en direcci6n a
personas ni animales.
[] Mantenga las manos y demos partes del cuerpo
lejos de la descarga. Por ejemplo, no intente
detener fugas con ninguna parte del cuerpo.
[] Utilice siempre la punta de rociado. No rode sin la
punta de rociado en su lugar.
[] Utilice Onicamente una punta de rociado
especificada por el fabricante.
[] Tenga precauciOn al limpiar y cambiar las puntas de
rociado. En el caso en que la punta de rociado se
obstruya durante el rociado, siga las instrucciones
del fabricante para apagar la unidad y aliviar la
presiOn antes de retirar la punta de rociado para
limpiada.
[] No deje la unidad sin supervisi6n cuando
est_ activada. Cuando la unidad no est_ en
funcionamiento, ap_guela segOn las instrucciones
del fabricante.
[] El rociado a alta presiOn puede inyectar toxinas en
el cuerpo y provocar lesiones corporales graves. En
el caso en que se produzca la inyecci6n, busque
atenci6n m6dica de inmediato.
[] Inspeccione que las mangueras y las piezas no
muestren seSales de da5o. Reemplace cualquier
manguera o pieza da5ada.
[] Este sistema es capaz de producir 17 236,89 kPa
(2 500 psi). Utilice solamente piezas o accesorios
de repuesto especificados por el fabricante y que
tengan una capacidad nominal de 17 236,89 kPa
(2 500 psi), como m[nimo.
[] Sepa c6mo detener la unidad r_pidamente.
Familiar[cese completamente con los controles.
[] Antes de hacer funcionar la unidad, verifique que
todas las conexiones scan seguras.
[] Para uso dom6stico Onicamente.
ADVERTENCIA: Para reducir el riesgo de lesiones:
[] No utilice la unidad ni rode cerca de los ni5os.
Mantenga alejados a los ni5os del equipo en todo
momento.
[] No se estire demasiado ni se pare sobre un soporte
inestable. Mantenga los pies bien asentados y el
equilibrio en todo momento.
[] Permanezca alerta y preste atenci6n a Io que est6
haciendo.
[] No use la unidad si est_ cansado o se encuentra
bajo los efectos de alguna droga odel alcohol.
3 =EspaSol

[] Mantengalasproteccionesensulugaryenbuenas
condicionesdetrabajo.NuncautiUiceUaherramienta
conningunadeUasproteccionesocubiertasquitadas.
AsegOresedequetodasUasproteccionesest6n
funcionandodeformacorrectaantesdeutiUizarUa
unidad.
[] Parareducirelriesgodelesiones,mantengaa
aUejadosanidosydemascircunstantes.TodosUos
presentesdebenHevarpuestosanteojosdesegundad
ypermaneceraunadistanciaseguradeU_reade
trabajo.
[] Mantengaalejadasdelareadetrabajoatodaslas
personas,particuUarmenteaUosnidosdecortaedad,
ytambi6naUasmascotas.
[] Usenaherramientaadecuadaalatarea.NofuerceUa
herramientaniningOnaccesorioaefectuartareaspara
lasquenoest_nhechos.NolauseparapropOsitosno
indicadosenlasinstrucciones.
[] Noaccioneel equipocuandoest_descalzooal
Hevarpuestassandaliasocalzadolivianosimilar.
Usecalzadodeseguridadqueleprotejasuspiesy
mejoresuposturaensuperficiesresbaladizas.
[] Tengasumaprecauci6nparaevitarresbaJarseo
caero
[] Siemprepongaseproteccionocularconlamarca
decumpHmientode_anormaANSmZ87°1°Conel
cumplimientodeestareglasereduceelriesgode
lesionescorporalesserias.
[] Uti_ices6_oaccesoriosrecomendados.Elempleode
accesoriosinadecuadospuedepresentarriesgosde
lesiones.
[] Siga1asinstruccionesdelamantenimiento
especificadasenestemanual
[] mnspeccionelaspiezasdaSadas°Antesdeseguir
utilizandolaherramienta,esnecesarioinspeccionar
cuidadosamentetodaprotecci6nopiezadadadapara
determinarsifuncionar_correctamenteydesempedar_
lafunciOnalaqueest_destinada.Verifiquela
alineaciOndelaspartesmOviles,quenohaya
atoramientodelasmismas,quenohayapiezasrotas,
elmontajedelaspiezasycualquierotracondici6nque
pudieraafectarsufuncionamiento.Todaprotecci6no
piezaqueest6dadadadeberepararseapropiadamente
oreemplazarseenuncentrodeservicioautorizado.
[] Nuncadejedesatendidaningunaherramientaen
funcionamiento°Apaguelaherramienta.Nose
alejedelaherramientahastanovedacompletamente
detenida.
[] FamiHadcesecomp_etamenteconloscontro_es.
Aprendaadetenerlam_quinayaliberarr_pidamente
lapresiOn.
[] Mantengalaherramientaseca,Jimpiay mibrede
aceitey grasa.Siempreutiliceunpanolimpioparala
limpiezadelaunidad.Nuncautilicefluidosparafrenos,
gasolina,productosabasedepetr61eonisolventes
paralimpiarlaherramienta.
[] Noutitice_aherramientasielinterruptornoapaga.
Uevetodointerruptordefectuosoauncentrode
servicioautorizadoparaqueIoreparen.
[] Antesdelimpiar,repararoinspeccionarlamaquina,
apagueelmotorycerci6resedequesehayandetenido
todaslaspartesenmovimiento.
[] EvitetenetunentornodetrabajopeHgroso.No
utiliceherramientasel6ctricasenlugareshOmedos
omojadosnilasexpongaalaIluvia.Mantengabien
iluminadael_readetrabajo.
[] Nuncadirijaunchorrodeaguaendireccion
depersonasoanimales,nihaciadispositivos
electricoso
[] Nuncapongaenmarchalamaquinasiseha
formadohieloencualquierpartedelequipo.
ADVERTENCIA:Los chorros de alta presion
pueden set peligrosos si se utiJizan indebidamente°
Nunca dirija el chorro a personas, animales,
dispositivos el6ctricos ni a la m_quina misma.
[] Evite eJcontacto con las partes caHentes de la unidad.
[] Antes de cada uso, inspeccione _os pernos y _as
tuercas para verificar que est_n apretados. Una tuerca
o perno sueltos pueden causar problemas graves en el
motor.
[] Antes de guardar deje que se enfde e_producto°
[] Guarde _aunidad en un _ugar frio y bien ventilado,
a una distancia segura de todo equipo generador de
chispas o llamas.
[] A] dar servicio a _aunidad, s6_o utiHce piezas de
repuesto id_nticas° El empleo de piezas diferentes
puede causar un peligro o da5ar el producto.
[] Nunca utHice e_ rociador sin _a punta de rociado
insta_ada.
[] Una _esi6n pot inyecci6n puede ocasionar una
posib_e amputaci6n° Consulte a un m_dico de
inmediato.
[] Nunca co_oque _a mano de,ante de _a punta de
rociado cuando use _a unidad. Los guantes no
siempre brindan protecci6n contra lesiones por
inyecci6n.
[] Cuando utHice _a unidad, use ropa que no
permita que _a pintura entre en contacto con
la pie_ ni e_ cabeHo, junto con una mascara o
un respirador. Las pinturas, los solventes y otros
materiales pueden ser da5inos si se inhalan o si
entran en contacto con el cuerpo.
[] Siempre apague _a unidad, quite e_ paquete de
baterias, y _ibere presi6n antes de dar servicio
a _a unidad, limpiar _a punta o la proteccion,
cambiar _a punta o dejar desatendida _a unidad.
[] El p]astico puede provocar chispas. Nunca utHice
p_astico para cercar un area de rociado. No
use protecciones de pl_stico al rociar materiales
infiamables.
4 EEspadol

Norocieene×terioresendiasventosos°
Nointentelimpiarni destaparmapuntade
rociadoconel dedo°
Toda herramienta de batedas, ya sea de batedas
integradas o de paquete de batedas separado,
debe recargarse Qnicamente con el cargador
especificado para 1asbatedaso Un cargador que
puede ser adecuado para un tipo de baterias puede
significar un riesgo de incendio si se empUeacon otro
tipo de bater[as.
[] Utilice _asherramientas de batedas s6_o con el
paquete de batedas especfficamente indicado° El
empleo de bater[as diferentes puede presentar un
riesgo de incendio.
[] Cargue 1as batedas solamente con eJcargador
indicado. Para utilizar con paquetes de batedas de
n_quel-cadmio de 19,2 V o de iones de _itio de 19,2
V, consulte el folleto de la herramientaiaparatoipaquete
de bater[asicargador complementario 988000-272.
[] Desconecte el paquete de batedas de la
herramienta o ponga el interrupter en la posicion
de aseguramiento o apagado antes de efectuar
ajustes, de cambiar accesorios o de guardar la
herramienta. Con tales medidas preventivas de
seguridad se reduce el riesgo de poner en marcha
accidentalmente la herramienta.
[] Cuando no este usando e_ paquete de batedas,
mantengalo aJejado de todo objeto metalico come:
dips, monedas, Haves, ctavos, torniHos y otros
objetos metalicos pequefios que puedan establecer
conexi6n entre ambas terminales. Establecer una
conexiOn directa entre las dos terminales puede causar
chispas, quemaduras o incendios.
[] Las herramientas de bater_as no se necesitan
conectar a una toma de corriente; per Io tanto,
siempre estan en condiciones de funcionamiento°
Este consciente de ruesposibtes peligros cuando no
este usando la herramienta de batedas o cuando
este cambiando los accesorios de la misma. Con el
cumplimiento de esta regla se reduce el riesgo de una
descarga el6ctrica, incendio o lesi6n corporal seria.
[] No coloque herramientas de baterias ni las baterias
mismas cerca del fuego o deJ caloro De esta manera
se reduce el riesgo de explosiones y de lesiones.
[] No aplaste, deje caer o dafie _a bateria. Nunca
utilice una bateda o cargador que se ha caido,
aplastado, recibido un go_pe contundente o ha side
dafiado(a} de alguna manera. Las bater[as da5adas
pueden sufrir explosiones. Deseche de inmediato toda
bater[a que haya sufrido una ca[da o cualquier da5o.
[] Las baterias pueden e×plotar en presencia de una
fuente de inflamacion, come una luz guia. Para
reducir el riesgo de lesiones corporales serias, nunca
use un producto inal_mbrico en presencia de llamas
expuestas. La explosi6n de una bater[a puede lanzar
fragmentos y compuestos qu[micos. Si ha quedado
expuesto a la explosion de una bater[a, I_vese de
inmediato con agua.
[] No cargue herramientas de baterias en lugares
mojados o humedos. Con el cumplimiento de esta
regla se reduce el riesgo de una descarga el6ctrica.
[] Para obtener resu_tados 6ptimos, debe cargar
la herramienta de baterias en un ]ugar deride _a
temperatura est_ entre 5O°F y 100°F. No guarde
la herramienta a _aintemperie ni en e_interior de
vehiculos.
[] En condiciones e×tremas de use o temperatura las
batedas pueden emanar _iquido. Si el liquido Itega a
tocar_e la piel, lavese de inmediato con agua y jab6n°
Si le entra liquido en los ojos, laveselos con agua
limpia per Io menos 10 minutes, y despu_s busque
de inmediato atencion m_dica. Con el cumplimiento
de esta regla se reduce el riesgo de lesiones corporales
senas.
[] Nunca deje desatendida ninguna herramienta con
la bateda insta_ada.
[] Guarde estas instrucciones. ConsOltelas
frecuentemente y util[celas para instruir a otros
usuarios. Si presta a alguien esta herramienta, facil[tele
tambi_n las instrucciones.
CALIFORNIA -PROPUESTA DE LEY N0_. 65
ADVERTENC_A: Este producto, y las pinturas dise5aron ser aplicados con este producto, pueden contener los
productos qu[micos, incluyendo el plomo,reconocidas per el estado de California come causantes de c_ncer,
defectos cong_nitos y otras afecciones del aparato reproductor. Lbvese tas manes despu#s de utilazar el
aparate.
Algunos ejemplos de estas sustancias qu[micas son:
o plomo de las pinturas a base de plomo,
silicio cristalino de los ladrillos, del cemento y de otros productos de mamposter[a, y
ars_nico y creme de la madera qu[micamente tratada.
El riesgo de la exposici6n a estos compuestos var[a, seg0n la frecuencia con que se realice este tipo de trabajo.
Para reducir la exposiciOn personal a este tipo de compuestos: trabaje en _reas bien ventiladas, y con equipo
de seguridad aprobado, tal come las caretas para el polvo especialmente dise5adas para filtrar part[culas
microsc6picas. 5 - Espa_ol

LassiguientespaUabrasdesedaUizaci6nysussignificadostieneneUobjetodeexpUicarUosniveUesdefiesgo
reUacionadosconesteproducto.
SiMBOLO SENAL SIGNIFmCADO
Indica una situaci6n peUigrosa inminente, UacuaU,si no se evita, causar_ Ua
PELJGRO: muerte o Uesionesserias.
Indica una situaciOn peUigrosa posibUe, UacuaU,si no se evita, podr[a
causar Uamuerte o Uesionesserias.
Indica una situaci6n potenciaUmente peUigrosa la cual, si no se evita,
puede causar lesiones leves o moderadas.
PRECAUCm6N: (Sin el s[mbolo de alerta de seguridad) Indica una situaci6n que puede
producir dados materiales.
Es posible que se empleen en este producto algunos de los siguientes s[mbolos. Le suplicamos estudiarlos y
aprender su significado. Una correcta interpretaci6n de estos s[mbolos le permitir_ utilizar mejor y de manera m_s
segura el producto.
SiMBOLO NOMBRE DENOMINACK) N/EXPLICACK)N
Alerta de seguridad
Lea el manual del operador
Protecci6n ocular
Symboles reciclar
Indica un peligro posible de lesiones personales.
Para reducir el riesgo de lesiones, el usuario debe leer y
comprender el manual del operador antes de usar este
producto.
Siempre p6ngase protecci6n ocular con protecci6n lateral con
la marca de cumplimiento de la norma ANSI Z87.1.
Este producto contiene bater[as de n[quel-cadmio (Ni-Cd) o
iones de litio (Li-ion). Es posible que algunas leyes municipales,
estatales o federales proh[ban desechar las bater[as de n[quel-
cadmio en la basura normal. Consulte a las autoridades
reguladoras de desechos para obtener informaci6n en relaci6n
con las alternativas de reciclado y desecho disponibles.
V Volts Voltaje
Corriente continua Tipo o caracter[stica de corriente
PSI Presi6n La presi6n se mide en libras per pulgada cuadrada
El caudal se mide seg0n la cantidad maxima de galones de
GPH Caudal pintura que se roc[a per hera
6 - Espadol

_=SPI=CIFiCACiONI=S DI=L PRODUCTO
Tamafio del contenedor .................................................................................................................................. 0,9464 I (! cto.)
Motor ............................................................................................................................................................. 19,2 V, corr. cont
CONOZCA SU ROCIADOR DE PINTURA
Vea /a figura 1,pbgina L
Para usar este producto con la debida segundad se debe
comprender la informaciSn indicada en la herramienta
misma yen este manual, y se debe comprender tambi6n
el trabajo que intenta realizar. Antes de usar este
producto, familiar[cese con todas las caracter[sticas de
funcionamiento y normas de segundad del mismo.
VISOR D_=L INDICADOR DE I=Nt=RGIA 03
El visor del indicador de energ[a C3 ubicado al costado
del mango se enciende luego de instalar y cargar un
compacto paquete de bater[a Craftsman de iones de litio
de !9,2 V (315.113710).
NOTA: Esta IAmpara no se encender_ con paquetes de
bater[as de n[queFcadmio Craftsman de 19,2 V.
NOVEDOSO DJSi=NO DI=L MOTOR
El novedoso dise_o del motor implica menos vibraci6n y
ruido al usar su rociador.
CONT_=NEDOR DE ASEGURAMIENTO
RAPIDO
La caracteristica de aseguramiento r_pido permite instalar
y eliminar f_cilmente el contenedor de pintura.
PUNTAS DE ROCiADO
Las dos puntas de rociado suministradas le permiten
elegir entre patrones de rociado diferentes: vertical,
horizontal, y circular
DESEMPAQUETADO
Embarcamos este producto completamente armado.
Extraiga cuidadosamente de la caja la producto y los
accesorios. AsegOrese de que est6n presentes todos
los art[culos enumerados en la lista de empaquetado.
_ ADVER'TENCIA: No use este producto si no est_
totalmente ensamblado o si alguna pieza falta o est_
da_ada. Si utiliza un producto que no se encuentra
ensamblado de forma correcta y completa, puede
sufrir lesiones graves.
Inspeccione cuidadosamente la producto para
asegurarse de que no haya sufrido ninguna rotura o
dado durante el transporte.
No deseche el material de empaquetado hasta que
haya inspeccionado cuidadosamente la producto y la
haya utilizado satisfactoriamente.
Si hay piezas dadadas o faltantes, le suplicamos llamar
a 1-800-932-3188, donde le brindaremos asistencia.
USTA DE EMPAQUETADO
Rociador de pintura con contenedor de aseguramiento
r_pido y punta ancha en abanico
V_lvula atomizadora de repuesto
Limpiador para brochas
Lubricante
Punta redonda
Manual del operador 7- Espadol
ADVERTENCIA, Si falta o est_ dadada
alguna pieza, no utilice este producto sin haber
reemplazado la pieza. Usar este producto con partes
da_adas o faltantes puede causar lesiones serias al
operador.
ADVERTENCIA; No intente modificar este
producto ni hacer accesorios no recomendados
para la misma. Cualquier alteraciOn o modificaci6n
constituye maltrato el cual puede causar una
condiciSn pe@rosa, y como consecuencia posibles
lesiones corporales serias.
ADVERTENCIA; Para evitar un arranque accidental
que podr[a causar lesiones corporales serias,
siempre desmonte de la producto el paquete de
bater[as al montade piezas a aqu611a.

ADVERTENCmA: No permita que su faminadzaci6n con
este producto nevuenva descuidado. Tenga presente
que un descuido de un instante es suficiente para
causar una nesi6n grave.
ADVERTENCIA: Siempre p6ngase protecci6n ocunar
con protecci6n naterancon namarca de cumpnimiento
de nanorma ANSI Z87.1. La inobservancia de esta
advertencia podria ocasionar naentrada de fiuidos en
sus ojos y provocar nesiones graves.
ADVERTENCmA: No utinice ningOn aditamento o
accesorio no recomendado pot enfabricante de esta
herramienta° Enempneo de aditamentos o accesorios no
recomendados podria causar nesiones serias.
uSOS
Este producto puede empnearse para enfines enumerado
abajo:
[] Pinturas y barnices para intedores y exteriores para
terrazas, muebles de extedores, cercas y paredes
Este producto acepta baterias de iones de %0 Craftsman _
de 19,2 V y de niqueFcadmio de 19,2 V.
Para ver las instrucciones de carga completas, consulte
el manual del operador de los paquetes de baterias y
cargadores enumerados en las Reglas de Seguridad
Especificas.
CARACTERiSTICAS DE PROTECCKSN DE LAS
BATERiAS
Las baterias de iones de %0 Craftsman _ 19,2 V est_n
disedadas con caracteristicas que protegen las celdas de
iones de litio y maximizan la duraci6n de las baterias.
Si la herramienta se detiene durante el use, suelte el gatillo
para reiniciarla y reanude el funcionamiento. Si aun asi no
funciona, se debe recargar la bateria.
PARA DESMONTAR YMONTAR EL PAQUETE DE
BATERiAS
Vea /a figura 2, pbgina L
_ ADVERTENCIA: Retire siempre el paquete de
baterias de la herramienta antes de instalar las piezas,
realizar ajustes° limpiada o cuando no la utilice° Retirar
el paquete de baterias evitar_ que la unidad se accione
accidentalmente y provoque lesiones graves.
Para conectar:
[] Coloque el paquete de baterias en la producto, alineando
la costilla realzada del paquete de baterias con el
recept_culo para baterias de la herramienta.
[] AsegOrese de que los pestillos situados en ambos lados
del paquete de baterias entren completamente en su lugar
con un chasquido y de que el paquete quede bien fijo en
la herramienta antes de empezar a utilizar la herramienta°
Para el desmontaje:
[] Opnma los pestillos a ambos lados para soltar y extraer el
paquete de baterias.
_ ADVERTENCmA: Las herramientas de baterias
siempre est_n en condiciones de funcionamiento. Pot
Io tanto, siempre debe estar asegurado el interruptor
cuando no est6 us_ndose o el operador Io Ileve per un
lade.
_ ADVERTENCmA: Riesgo de incendio o explosi6n. El
_rea de rociado debe estar bien ventilada y lejos de
chispas o llamas.
LLENADO DEL ROCIADOR CON PmNTURA/TINTE
Vea /a figuras 3 y 4, pbgina L
Retire y deseche cualquier capa que se haya formado en
la superficie de la pintura o del tinte, luego mezcle bien el
material en su contenedor original antes de comenzar a
pintar.
NOT,&: Es posible que se deba filtrar los contenedores de
tinte y pintura mAs antiguos antes de usar el rociador.
[] Quite el paquete de baterias del rociador.
[] Retire el contenedor de aseguramiento r_pido gir_ndolo a
la izquierda de tal manera que la fiecha del contenedor se
alinee con el simbolo "desasegurar" de la tapa°
[] Llene el contenedor con pintura o tinte segOn se desee°
No llene por encima de la marca de llenado maximo del
contenedor.
[] Vuelva a instalar el contenedor en el rociador y girela a
la derecha de tal manera que la fiecha del contenedor se
alinee con el simbolo "asegurar" en la tapa°
SELECCI6N DE LA PUNTA DE ROCIADO
ADECUADA
Vea /a figura 5, pbgina ft.
Utilice una punta de ventilador redonda para
materiales como pinturas I_tex y come pinturas
y manchas al aceite. Esta redonda tiene un
patr6n de rociado redondo°
Utilice una punta ancha en abanico de ancho
para materiales come pinturas I_tex. Esta
redonda ancha en abanico tiene un patr6n
de rociado ancho que puede ajustarse de
horizontal a vertical.
Para cambiar las puntas:
[] Quite el paquete de baterias del rociador.
[] Retire la punta instalada gir_ndola a la izquierda.
[] tnstale la punta deseada, girela a la derecha y apri6tela
firmemente.
NOTA: La punta debe apretarse firmemente con la mano°
Una punta demasiado floja o demasiado apretada puede
provocar que el rociador presente fugas o da_os.
8 =Espadol