Craftsman 172.26729 User manual

Owner's Manual
ICRAFTSMANI
31/4-1N. PLANER
Model No.
172.26729
CAUTION: Read, understand and follow
all Safety Rules and Operating Instructions
in this manual before using this product,
•SAFETY
•OPERATION
•MAINTENANCE
•ESPANOL,PAGINA 21
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

J Z_ WARNING: BE SURE to read and understand all instructions.Failure J
to follow all ip_ructions listed below may result in electric shock, fire and/or I
serious personal injury.
WORK AREA SAFETY
1. ALWAYS keep your work area clean and well IlL Cluttered and dark areas
Invite accidents.
2. DO NOT operate power tools In explosive atmospheres, such as In the
pm._e.nce of flammable liquids, gases, or dust. Power toolscreate sparks
wnucnmay ignitethe oustor Rimes.
3. ALWAYS keep bystanders, children and visitors away while operating a
power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
1. Double Insulated tools ere equipped with e polarized plug (one blade Is
wider than the other). This plug will fit in a polarized outlet only one way.
If the plug does not fit fully into the outlet, reverse the plug. If It still
does not tit, contact a qualified electrician to Install a potarlzed outleL
DO NOT change or alter the plug In any way.
2. Double insulation [] eliminates the need for the three wire grounded power
cord and grounded power supply system. Applicable only to Class II
(double insulated) tools.
3. Before plugging in the tool BE SURE that the outlet voltage supplied is
within the voltage marked on the tool's data plate. DO NOT use =AC only"
rated tools with a DC power supply.
4. ALWAYS avoid body contact with grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased dsk of electric
shock if your body is grounded.
5. If operating the power tool In damp locations Is unavoidable, ALWAYS
use a Ground Fault Circuit Interrupter to supply power to your tool.
ALWAYS wear electrician's rubber gloves and footwear In damp
conditions.
6. DO NOT expose power tools to rein or wet condlUons. Water entering a
power tool will increase the dsk of electric shock.
7. DO NOT abuse the cord. NEVER use the cord to carry the tools or pull
the p.lug from the outlet. Keep cord away from heat, o11,sharp edges or
movnng parts. Replace damaged cords Immediately. Damaged cords
increase the risk of electric shock.
8. When operating apower tool outside, ALWAYS use an outdoor extension
cord marked "W-A" or _These cords are rated for outdoor use and reduce
the risk of electric shock.
NOTE: The extension cord must have adequate wire size AWG
(American Wire Gauge) for safe, efficient use. Smaller gauge wires have
greater capacity (16 gauge wire has more capacity than 18 gauge wire).
3

PERSONAL SAFETY
1. ALWAYS stay alert, watch what you are doing and use common sense
when operatlng s power tool. DO NOT use tool while tired or under the
influence of drugs, alcohol or medication. A momentof inattentionwhile
operatingpowertools may result in seriouspersonal injury.
2. ALWAYS dress properly. DO NOT wear loose clothing or Jewelry. Pull
back long hair. Keep _/our hair, clothing and gloves away from moving
parts. Looseclothing,jewelry or long haircan be caught in moving parts.
3, ALWAYS avoid accidental starting. BE SURE switch Is in the "Off"
position before plugging in. DO NOT carry toolswith yourfinger onthe
switch.Carrying toolswithyourfinger on the switch or pluggingin toolsthat
have the switch in the"On"positioninvitesaccidents.
4. ALWAYS remove adjusting keys or wrenches before turning the tool on.
.Awrench or akey that isleft attached to a rotating part ofthe toolmay result
in personal injury.
5. DO NOT overreach. ALWAYS keep proper footing and balance at all
times. Proper lootingand balance enables better controlofthe toolin
unexpected situations.
6. ALWAYS use safety equipment. Always wear eye protection. Dust mask,
non-skidsafety shoes,hard hat, or hearing protectionmustbe usedfor
appropriate conditions.
TOOL USE AND CARE SAFETY
1. ALWAYS use clamps or other practical ways to secure and support the
work piece to a stable platform. Holdingthe work by handor againstyour
body is unstableand may teedto lossofcontrol.
2. DO NOT force the tool. Use the correct tool for your application.
The correcttoolwilldo the job betterand safer at the rate for whichitis
designed.
3. DO NOT use the tool if the switch does not turn it "On" or "Off", Anytool
that cannot be controlledwiththe switchisdangerous and mustbe repaired.
4. ALWAYS disconnect the plug from the power source before making any
adjustments, changing accessories or storing the tool. Suchpreventive
safety measures reducethe risk ofstartingthe toolaccidentally.
5. ALWAYS store Idle tools out of the reach of children and other
untrained persons. Toolsare dangerousin the handsof untrainedusers.
6. ALWAYS maintain tools with care. Keep cutting tools sharp and clean.
Properly maintainedtoolswithsharp cuttingedges are lesslikelyto bind and
are easier to control.
7. ALWAYS check for misallgnment or binding of moving ports, breakage
of parts, and any other condition that may affect the tool's operation.
If damaged, have the tool serviced before using. Many accidentsare
caused by poorly maintained tools.
4

TOOLUSEANDCARESAFETYcont.
/_ WARNING: USEOFACCESSORIESTHATARENOT RECOMMENDED I
FOR USEWITHTHISTOOLMAYCREATEA HAZARDOUSCONDITION. I
8. ALWAYS use only accessorles that are recommended for this tool.
Accessories that may be suitablefor one tool can become hazardous when
used on anothertool.
SERVICE SAFETY
I. If any part of this planer is missing or should break, bend, or fail in any
way; or should any electrlcal component fall to perform properly:
ALWAYS shutoffthe powerswitchand remove theplaner plugfrom the
powersourceand have the missing,damaged or tailed parts replaced
BEFORE resuming operation.
2. When servicing a tool, ALWAYS use only Identical replacement parts.
Follow Instructions In the maintenance section of this manual. Use of
unauthorizedparts may create a riskof electricshockor injury.
3. Toolservice MUST BE performedonlyby a Sears Partsand Repair Center.
Service or maintenanceperformedby unqualifiedpersonnelcouldresultin a
riskof injury.
ADDITIONAL RULES FOR SAFE OPERATION
,/_ WARNING: BE SURE to readand understandall instructions.Failure I
tofollow all instructionslisted below may resultinelectricshock,fire and/or I
serious personal injury.
1. Know your power tool. Read operator's manual carefully. Learn the
applications and limitations as well as the specific potential hazards
related to th s tool. Followingthis rule willreducethe nsk ofelectric shock,
fire or serious injury.
2. ALWAYS wear safety glasses or eye shields when using this planer.
Everyday eyeglasses have only impact-resistant lenses; they are NOT
safety glasses. Followingthis rulewill reducetherisk of serious personal
injury.
3. ALWAYS protect your lungs.Wear a face mask or dust mask if the
operation is dusty. Followingthis rule willreducethe riskofserious
personal injury.
4. ALWAYS protect your hearing.Wear hearing protection during
extended periods of operation. Followingthisrulewillreduce the risk of
seriouspersonalinjury.
5. ALWAYS inspect the tool cords periodically and if damaged have them
repaired at your nearest Sears Service Center or other Authorized
Service Facility. ALWAYS be aware of the cord location. Followingthis
rule will reduce the risk of electric shock or fire.

ADDmONAL RULES FOR SAFE OPERATION cont.
6. ALWAYS check for damaged parts. Before further use of the toot,
a guard or other part that is damaged should be carefully checked to
determine If it will operate properly and perform its intended function.
Check for misallgnment or binding of moving pads, breakage of parts,
and any other condition that may affect the tool's operation. A guard or
other part that is damaged should be properly repaired or replaced at
a Sears Service Center. Followingthis rulewillreduce the riskofa ectr c
shock,fire or seriousinjury.
7. DO NOT abuse the cord. NEVER use the cord to carry the tools or pull
the plug from the outlet. Keep cord away from heat, oil, sharp edges or
moving parts. Replace damaged cords immediately. Damaged cords
increasethe risk ofeleCtriCshock. Followingthis rulewillreducethe riskof
electricshock or fire.
8. ALWAYS make sure that your extension cord Is in good condition.
When using an extension cord be sure to use one that is heavy
enough to carry the current that your tool will draw. Awire gauge
(AWG) of at least 14 is recommendedforan extensioncord25 feet or less
in length.When workingoutdoorsALWAYS use an extensioncordthatis
suitablefor outdoor use.The cord'sjacket willbe marked WA.
Smatter gauge wires, have greater capacity (16 gauge wire has more
capacity than 18 gauge wire). An undersizedcordwillcause adrop in
line voltage, resultingin lossof powerand overheating.
9. ALWAYS inspect and remove all nails from lumber before planing,
Followingthis rulewillreduce the riskof seriouspersonalinjury.
10. DO NOT use the tool while tired or under the Influence of drugs,
alcohol or any medication. Followingthis rule willreduce the riskof
electricshock,fire or serious persona_iniury.
11. SAVETHESE INSTRUCTIONS. Refer to them frequently and use them
to instruct others who may use this tool. If someone borrows this tool,
make sure they have these instructions also.
6

ADDITIONAL RULES FOR SAFE OPERATION cont.
/_ WARNING: The operationof any planer can result
in foreign objectsbeingthrownintoyour eyes,whichcan
resultin severeeye damage. Beforebeginning powertool
operation,ALWAYS wear safetygogglesor safetyglasses
with sideshieldand a fullface shield when needed.
We recommendAWide VisionSafety Mask for useover
eyeglassesor standardsafety glasses with side shield,
available at Sears RetailStores.
L_WARNING: Some dust particles created by power sanding, sawing,
grinding, drilling and other construction jobs contain chemicals known to
cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• Lead from lead-based paints.
•Crystallinesilica from bricks and cement and other masonryproducts.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending upon how often you do this
type of work.To reduce your exposure to these chemicals:
•Work in a well-ventilated area.
•Work with approved safety equipment such as those dust masks that are
specially designed to filter out microscopic particles.
The label on your tool may include the following symbols.
V........................................................................... Volts
A.......................................................................... Amperes
Hz........................................................................ Hertz
W.......................................................................... Watts
rain ...................................................................... Minutes
........................................................................ Alternating current
.... ................................................................... Direct current
no ........................................................................ No-load speed
[] ........................................................................ Class II construction
.../rain .................................................................. Revolutions or
reciprocation per minute
Z_ ........................................................................ Indicates danger, warning
caution. It means attention!!!
Your safety is involved,
IMPORTANT! READ ALL INSTRUCTIONS
7

KNOWYOURPLANER(SeeFig.1)
Beforeattempting to use any tool, be ,suretofamiliarizeyourselfwith all the
operatingfeatures and safety instructions.
Yourplaner has many built-inconveniencefeatures for fast, efficientcutting.
It iscompact and lightweightfor easy,comfortableuse.The depth adjustment
knob isconveniently locatedat the front of the planer and allowseasy depth
adjustmentsfrom 0 to 1/8-in. to suityour needs.
Yourplaner uses reversible,double-edgedhardened steel carbide-tippedblades
that allow useon bothsides for longerbladelife.It includesedge guide for
accurate cuts on long or unevenwork pieces.The rabbet guide allowsyou to
make rabbetcuts up 15/16 in.deep.
Electrical Connection
Yourplaner has a precision-builtelectricmotorand it shouldonly beconnected
toa 120-volt, 60-Hz. power supply (normal household current). DO NOT
operate on directcurrent (DC).This largevoltage dropwillcause a lossof
powerthat witloverheatthe motor.If yoursaw does notoperate when plugged
intoan outletcheckthe powersupply.
Trigger Switch and On/Off Button
To turnon the planer press and hold theOn/Off buttonand squeezethe trigger
switch.When you are finished planing,release switchto shuttool off.
Adjustable Left or Right Dust /Chip Extraction
The dust/chipchute can be adjusted forleftor rightextractionby turningthe
chute clockwiseor counterclockwise.
Base Plate Stand
Whenever you place the planer ontoa work surface,the rear of thebase plate
shouldbe elevated on thisstand.Thiswillhelp protectthe planer bladesfrom
damage and help preventthe blades from accidentallydamagingthe work
surface.As you begin to plane, this stand willhe pushedaway bythe work
surface.ALWAYS besure thatthe stand moveseasily on the base plate.

input
Cutting Width
Cutting Depth
Max. Rabbet Cut
Rating
No-Load Speed
7 Amps
3 1/4 in.
0 to l/B-in.
15/16-in.
120 volts, 60 Hz AC
12,000 RPM

I/Jk WARNING: YourplanershouldNEVERbeconnectedtopowersupply I
|
whenyouareassemblingparts,makingadjustments,changingbeltsorblades, I
cleaningplaner,orwhennotin use,Disconnectingplanerwillpreventaccidental
startingthatcouldcauseseriousinjury.
PREPARING FOR OPERATION
Yourplaner has a rear handle and frontassist handlefor ease of
operation.Theyprovide the two-hand operationwhichisnecessaryto maintain
propercontrolofthe planer.ALWAYS keep bothhandsclear of the bladesand
the cuttingarea.
ALWAYS usa bothhandswhen usingthe planer.Hold thefront handlewith
yourlefthand and the rear handlew_h yourrighthand (as shownin Fig.2).
This positionmakes yourplaner easier to handle and keepsyouclear ofthe
chip exhaust.
The work movingduringacutcould resultin the lossof controlof the planer,
possiblycausingserious injury.
A !
ZL_ CAUTION: DO NOT plane toofast because this causesbuildup in I
the chipexhaust.Chip build-up restrictsair flow and cancausethe motorto I
over heat.
Keep the cordaway from the cuttingarea. ALWAYS place the cord soitdoes
nothang on the workwhen you are makingacut.
/_, DANGER: Ifthe cordhangs upon thework duringthecut, releasethe I
tdggerswitchimmediately.Unplugthe planerand checkthecordfor damage. I
Ifthereisno damage, repositionthecordtopreventitfrom hangingup again.
Ifthecord has been damaged,haveitreplacedbefore usingyourplaner.
Z_ WARNING: Usingyourplaner witha damaged cordcouldcause I
electricalshockresulting in seriousinjury. I
THE CORRECTWAYTO USEYOUR PLANER (See Fig. 2)
ALWAYS holdyourplaner as shownin Figure 2.
1. ALWAYS keep controlofyour planer.It makes cuttingeasier and safer,
as shownin Figure2.
2. To helpkeep control ALWAYS supportyourwork so the cutwillbe on
yourright.
3. ALWAYS clamp yourworkso it does not moveduringthe cut(see Figure2).
The work moving duringa cutcould resultinthe loss ofcontrolofthe planer,
possiblycausing serious injury.
The work movingduring a cut couldresultin the loss ofcontrolofthe planer,
possiblycausingserious injury.
10

THECORRECTWAYTOUSEYOUR
PLANER(SeeFig,2)cont.
4,ALWAYSoperatetheplanerwiththe
chipchuteexhaustturnedsoit points
away from yourface and eyes.
All visitorsshould wear safetyglasses
and be kept a safe distance from the
work area.
5, ALWAYS hold your planer so the
blades DO NOT come in contact with
the workpiece BEFORE you squeeze
the trigger switchand start the planer.
Z_ WARNING: Keep a firm
grip on the tool with both hands at
all times. Failure to do so could
result in loss of control leading to
possible serious injury.
TO ADJUST PLANING DEPTH (See Fig. 3)
The planing depth on yourplaner can be adjusted from 0 to 1/8 inch by rotating
the depth adjustment knob located on the front of your planer,
1. Unplug your planer.
Istarting, causing serious injury.
Z_ WARNING: Failure to unplug your planer could result in accidental I
2. To increase cutting depth rotate
knob n a cockwisedirection.
3. To decrease cutting depth, rotate
knob inacounterclockwisedirection,
4. We recommend thatyou make test
cutsin scrap woodafter each
adjustmentto make sure the planer
is removingthe desired amount
of wood.
NOTE: To protect the blades during
storage, transporting and when not
in use, ALWAYS set the blade depth
adjustment to 0.
11