Creality CR-Laser Falcon User manual

CR-Laser Falcon
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch

2
English
3 –17
Čeština
18 –32
Slovenčina
33 –47
Magyar
48 –63
Deutsch
64 –79

3
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
󲐜󲐝󲐞󲐟󲐠www.alza.co.uk/kontakt
✆[phone]
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7, www.alza.cz

4
Rendering picture
Dear Consumers:
Thank you for choosing our products. For the best experience, please read the
instructions before operating the machine. Our teams always be ready to render you
the best services. Please contact us via the phone number or e-mail address provided at
the end when your encounter any problem.
For a better experience in using our product, you can also learn how to use the
engraving machine in the following ways:
•View the accompanied instructions and videos in the TF card.
•Visit our official website www.creality.com to find relevant software/hardware
information, contact details, operation and maintenance instructions.
Firmware Upgrade
Download the latest firmware from https://www.creality.com/pages/download/-cr-laser-
engraver, save the “.bin” in the root directory of the TF card, and delete other files in TF
card. Insert the TF card into the machine when powered off, and it will update
automatically when powered on. The buzzer will sound in the update process. When the
update is completed, the sound will stop (do not power off in the update process).

5
Security Statement
For the purpose of engraving or cutting with a laser engraving machine, allow the
workpiece to be exposed to the high-density laser beam emitted by the laser engraving
machine. The workpiece may be subject to gasification without combustion as it is pretty
hot on the surface. On the other hand, most workpieces are essentially combustible,
which may be ignited, leading to an open flame and consequently to the machine
breakdown and environmental contamination.
1. It is prohibited to store the machine in areas close to combustible and explosive
substances, volatile solvents or source or heat. Instead, store it in a well-
ventilated, cool and dust-free place.
2. Make sure that only the specific attached power cord rather than other similar
power cords are used during installation.
3. Clean the tripod and laser module with a dry cloth regularly when the power is
off.
4. Ensure to run the laser at 0°C-35°C. It is prohibited to run the machine under wet
environment or in thunderstorm weather.
5. Switch off the machine if it is offline for an extended period of time, and unplug
the power cord.
6. It is prohibited to come in contact with electronic areas with hands or other tools
when the machine is connected to power supply.
7. Touching any moving parts and laser module while the machine is running is
prohibited.
8. Before engraving, place a flat object that cannot be penetrated by the laser, such
as an aluminium alloy or stainless-steel plate on the workbench, and then place
processing material.
9. Wear goggles to prevent vision damage arising from exposure to the laser spot
during laser engraving operation.
10. It is advisable to run the machine under well ventilated condition as laser
engraving may generate small amount of fume or gas.
11. Children under 10 years old are not allowed to run the machine without adult
presence, which otherwise may lead to personal injury.
12. Put in place fire extinguishers in case of use, which shall be regularly checked. It
is prohibited to keep the machine unattended while it is running.
13. Users should comply with the laws and regulations of the corresponding
countries and regions where the equipment is located (used), abide by
professional ethics, play attention to safety obligations, and strictly prohibit the
use of our products or equipment for any illegal purpose. Creality will not be
responsible for any violators’ legal liability under any circumstance.

6
Parameters
Model
CR-Laser Falcon
Machine size
568*632*198mm
Net weight
3.2kg
Operation system
Windows/MacOS
Input
100-240V ~ 50-60Hz
Output
DC 24.0V 3.0A
Range of operating temperature
0°C-35°C
Safety certification
IEC60825, FDA, CE, ROHS, FCC, UKCA, UL,
PSE
Engraving size
400mm*415mm
Laser source
Semiconductor laser unit
Laser wave length
455±5nm
Laser power
5W/10W
Safety class
Class IV (FDA/FDA classification standard)
Laser engraving software
LaserGRBL, LightBurn
Format files
jpeg, jpg, png, bmp, svg, dxf
Type of supporting materials
Cardboard, wood, bamboo, rubber,
leather, fabric, acrylic, plastic, etc
Equipment Intro
Rear X-axis profile
Left Y-axis
assembly
Tripod
Right Y-axis assembly
Tripod
Front X-axis
profile
Control box
assembly
Power interface
Type-C interface
TF card slot
Tripod
X-axis
assembly
Laser
module (5W)

7
Parts List
X-axis assembly & Control box assembly
Laser module x 1
Front X-axis profile*1
Power adaptor*1
Left Y-axis
assembly
Tripod
Tripod
Rear X-axis profile
X-axis
assembly
Right Y-axis assembly
Power interface
Type-C interface
TF card slot
Control box
assembly
Front X-axis
profile
Tripod
Laser module
(10W)
Multi-level
fixed focus bar
5W
or
10W

8
Rear X-axis profile*1
Power cord*1
Left Y-axis assembly*1
Linden plywood*2
Right Y-axis assembly*1
M5*20 screws*18
Tripod*3
T-shaped nuts*4
M1.5/,M2/M2.5/M3 Allen key
Activated carbon smoke absorption
cotton*2
Open wrench*1
Black cable tie*3

9
TF card & card reader *1
Dustless cloth*1
Goggles*1
Instruction manual*1
Multi-level fixed focus bar
Only for 10W laser module
Assemble directions
Assemble the left Y-axis assembly: Pass the left Y-axis assembly (with the belt up)
through the X-axis assembly and put on the belt in the direction shown in the figure:

10
Assemble the right Y-axis and it is the same as above. Insert two T-shaped nuts into the
left and right Y-axis assembly.
Assemble rear X-axis profile and front X-axis profile: Lock with eight M5*20 screws.
Assemble three tripods and control box assembly: Lock with eight screws. Push the X-
axis assembly to the end and make sure it is parallel to the rear X-axis profile.
T-shapeed
nuts
label
Grandienter

11
Tighten the belt and lock the belt with hexagon screws.
Assemble 5W laser module: Assemble it into the fixing plate and the fixed focus bar
should contact with the surface of the processed material when it is naturally vertical
downward. Then lock it with two hand screws on the right and turn the fixed focus bar
clockwise until it is attracted by the magnet. Finally plug in the laser module cord.
Assemble 10W laser module: Please place the multi-level fixed focus bar between the
laser module and the processed material. Follow the tips and make the bottom of the
laser module contact with the corresponding surface of the multi-level fixed focus bar.
Finally lock with two hand screws on the right. For example, if you engrave or cut a 2mm
basswood or other material:
T-shaped nuts
Not to lock too highly to prevent the
belt from perforating.
Laser module cord
Fixed focus bar
2mm Basswood

12
For better engraving effect, try to elevate the laser module as far away from the
workbench as possible on the premise that the focal length is correct.
The laser module must be installed and removed only when the power is off.
Software installation and usage guide
The machine supports real-time working by Type-C (LightBurn or LaserGRBL) and offline
working (LightBurn only).
Laser module
Multi-level fixed focus bar
2mm Basswood
Engrave/Cutting Thickness Of Basswood 1-3mm
Cutting Thickness Of Basswood 4-6mm
Cutting Thickness Of Basswood > 6mm

13
Start Engraving
Please follow the assembly directions to focus correctly and wipe the protective lens of
the laser module with dustless cloth and alcohol to ensure the best engraving effect.
The filter cotton in 5W lase module and the cover for 10W laser module can be removed
directly for cleaning.
Offline working
First generate and engraving file (.gcode/.gc/.g/.nc/.ngc) through LightBurn, and save it
to the root directory of the TF card (The machine reads the engraving file whose
modified date is latest in the root directory of the TF card by default. It is recommended
to delete other engraving files in the root directory) Insert the TF card before powering
on, connect the machine with the supplied power adapter and power cord. Finally turn
on the red switch on the left side of the control box.
When power on, the machine emits “beep, beep, beep”. After the machine is initialized, it
enters the standby mode, and the indicator light turns into breathing state.
Protective lens
Swich
Power
interface
TF card slot

14
Press the microswitch, it enters preview mode from standby mode, the laser head will
emit weak light, and repeat movement around the largest X, Y, edges of the processed
picture with indicator light on. At this time, adjust the material to a suitable position.
In preview mode, press microswitch again, it enters engraving mode. At this time, the
laser head will emit strong light, the machine will start engraving with indicator light on.
Pause engraving: press the microswitch (or click “Pause” button in the software). At this
time, the indicator turns into breathing light. Press the microswitch again to continue
engraving.
Cancel engraving: Please press and hold the microswitch for 3 seconds (or click “Cancel”
button in the software), it will “beep” once, starts to reset, and “beep” twice after reset is
complicated. Enter standby mode, the indicator light turns into breathing light.
After engraving is completed, it will “beep” three times and reset. After reset completed,
it “beep” twice, enters standby mode, and the indicator light turns into breathing light.
Real-time working
For real-time working by Type-C, please refer to the tutorial in the TF card. During online
working, do not insert the TF card and do not press the microswitch on the control box.
Indicator status
1. Light off: The machine is in power-off state, or the power is abnormal.
2. Breathing light: The machine is in standby mode, you can press the microswitch
to enter preview mode or engraving mode. (Present a light effect with a gradual
change or light shade).
3. Light flashes: the machine is in upgrade mode or abnormal, and the buzzer
beeps rapidly, and it will automatically enter standby mode after the upgrades is
completed or the abnormality is cleared.
4. Light always on: the machine is in preview mode or engraving mode. The laser
head is working, please pay attention to safety.
Microswitch

15
Exception Handling
If the machine turns on it side or moves suddenly during working, it will turn off the
laser. Motor stops moving, indicator light flashing, and buzzer emits alarm.
Solution: Please move the machine to its original position and press microswitch on the
machine control box to continue previewing or engraving after clearing abnormality (The
microswitch only works during offline working).
Offline working
Place a metal protective
plate and engraving
material
Adjust the focal length
of the laser module
Save the engraving file
to the TF card
Insert the TF card
Power on
Machine resets
Wait for the machine to
complete resetting
Press microswitch to
enter previewing mode
Press microswitch to
start engraving
Continue
engraving
Pause engraving
Stop engraving
End
Start
Press microswitch,
Yes or No
In pausing mode,
Yes or No
Long press
Short Press
Yes
No

16
Real-time working
Place a metal protective plate
and engracing material
Adjust the focal length of the
laser module
Use the Type-Cd date cable to connect
the computer and the engraving
machine
Power on
Select the corresponding COM
port to connect the machine
Import a picture
Set paramters
Frame-preview
Start engraving
End
Start

17
Warranty Conditions
A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you
need repair or other services during the warranty period, contact the product seller
directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for
which the claimed claim may not be recognized:
•Using the product for any purpose other than that for which the product is intended
or failing to follow the instructions for maintenance, operation, and service of the
product.
•Damage to the product by a natural disaster, the intervention of an unauthorized
person or mechanically through the fault of the buyer (e.g., during transport,
cleaning by inappropriate means, etc.).
•Natural wear and aging of consumables or components during use (such as
batteries, etc.).
•Exposure to adverse external influences, such as sunlight and other radiation or
electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage,
electrostatic discharge voltage (including lightning), faulty supply or input voltage and
inappropriate polarity of this voltage, chemical processes such as used power
supplies, etc.
•If anyone has made modifications, modifications, alterations to the design or
adaptation to change or extend the functions of the product compared to the
purchased design or use of non-original components.

18
Vážený zákazníku,
Děkujeme vám za zakoupení našeho produktu. Před prvním použitím si prosím pečlivě
přečtěte následující pokyny a uschovejte si tento návod k použití pro budoucí použití.
Zvláštní pozornost věnujte bezpečnostním pokynům. Pokud máte k přístroji jakékoli
dotazy nebo připomínky, obraťte se na zákaznickou linku.
󲐜󲐝󲐞󲐟󲐠www.alza.cz/kontakt
✆[phone]
Dovozce Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

19
Vykreslování obrázku
Vážení spotřebitelé:
Děkujeme, že jste si vybrali naše výrobky. Pro co nejlepší zážitek si před použitím
přístroje přečtěte návod k použití. Naše týmy jsou vždy připraveny poskytnout vám ty
nejlepší služby. Pokud se setkáte s jakýmkoli problémem, kontaktujte nás prosím
prostřednictvím telefonního čísla nebo e-mailové adresy uvedené na konci.
Pro lepší zkušenosti s používáním našeho výrobku se můžete také naučit, jak gravírovací
stroj používat následujícími způsoby:
•Prohlédněte si přiložené pokyny a videa na kartě TF.
•Navštivte naše oficiální webové stránky www.creality.com, kde naleznete
příslušné informace o softwaru/hardwaru, kontaktní údaje, návod k obsluze a
údržbě.
Aktualizace firmwaru
Stáhněte si nejnovější firmware z webu https://www.creality.com/pages/download/-cr-
laser-engraver, uložte soubor ".bin" do kořenového adresáře karty TF a odstraňte ostatní
soubory na kartě TF. Když je zařízení vypnuté, vložte do něj kartu TF a po zapnutí se
automaticky aktualizuje. Během procesu aktualizace zazní zvukový signál. Po dokončení
aktualizace se zvuk zastaví (během procesu aktualizace nevypínejte napájení).

20
Prohlášení o bezpečnosti
Pro účely gravírování nebo řezání laserovým gravírovacím strojem nechte obrobek
vystavit laserovému paprsku o vysoké hustotě, který laserový gravírovací stroj vysílá.
Obrobek může být vystaven zplynování bez hoření, protože je na povrchu dosti horký.
Na druhou stranu je většina obrobků v podstatě hořlavá, což může vést k jejich vznícení,
otevřenému plameni a následně k poruše stroje a kontaminaci životního prostředí.
1. Je zakázáno skladovat stroj v blízkosti hořlavých a výbušných látek, těkavých
rozpouštědel nebo zdrojů tepla. Místo toho jej skladujte na dobře větraném,
chladném a bezprašném místě.
2. Dbejte na to, aby se při instalaci nepoužívaly jiné podobné napájecí kabely, ale
pouze konkrétní připojený napájecí kabel.
3. Při vypnutém napájení pravidelně čistěte stativ a laserový modul suchým
hadříkem.
4. Zajistěte, aby laser pracoval při teplotě 0-35 °C. Je zakázáno provozovat stroj ve
vlhkém prostředí nebo za bouřky.
5. Pokud je stroj delší dobu mimo provoz, vypněte jej a odpojte napájecí kabel.
6. Když je stroj připojen k napájení, je zakázáno dotýkat se rukama nebo jinými
nástroji elektronických oblastí.
7. Dotýkat se pohyblivých částí a laserového modulu za chodu stroje je zakázáno.
8. Před gravírováním položte na pracovní stůl plochý předmět, kterým laser
nepronikne, například hliníkovou slitinu nebo desku z nerezové oceli, a poté na
něj umístěte materiál pro zpracování.
9. Používejte ochranné brýle, abyste zabránili poškození zraku v důsledku působení
laserového záření během laserového gravírování.
10. Doporučujeme provozovat stroj v dobře větraných podmínkách, protože při
laserovém gravírování může vznikat malé množství dýmu nebo plynu.
11. Děti mladší 10 let nesmějí stroj provozovat bez přítomnosti dospělé osoby, jinak
by mohlo dojít k úrazu.
12. Pro případ použití umístěte hasicí přístroje, které budou pravidelně kontrolovány.
Je zakázáno nechávat stroj za chodu bez dozoru.
13. Uživatelé by měli dodržovat zákony a předpisy příslušných zemí a regionů, kde se
zařízení nachází (používá), dodržovat profesní etiku, dbát na bezpečnostní
povinnosti a přísně zakázat používání našich výrobků nebo zařízení k jakýmkoli
nezákonným účelům. Společnost Creality za žádných okolností nenese
odpovědnost za právní odpovědnost porušovatelů.