Creative sysUSA ChoiBox Series User manual

ChoiBox Series
CS-RGB8g
Logic interface box for multicolor LED indicator with soft switch input

Rear Panel
1. Power Input
External DC Power supply 12V 3A
2. I/O control port
External control port inputs and output
3. LED Color select and Mode switch
SW1,2,3 R,G,B Color select when LED input pin level High
SW4,5,6 R,G,B Color select when LED input pin level LOW
SW7,8,9 R,G,B Color select when Logic input pin level LOW
SW10 Mode SW Solid or Blinking LED with Logic Input pin level LOW
4. Remote Button
Field test button (Same as when Remote pin input level is LOW)
5. LED/Logic Button
Field test button (Same as when LED/Logic input level is LOW)
1
2
3
4
5

Front Panel
1. Indicator Color Status
Seven different colors selectable with dip switch setting
2. Blinking Period Adjust Knob
Adjustable LED Blinking speed with Dip SW10 UP position when Logic input pin level is LOW
3. Remote Indicator
White LED indicates an active Remote input pin
4. Button Switch Action Indicator
Yellow ( or Green Left ) LED indicates an active button port (RJ45 Pin 1 Low indicator)
5. Additional Switch Action Indicator
Green ( Right ) LED indicates an active port feature switch ((RJ45 Pin 5 Low indicator)
6. 8 x RJ45 ports
8 ports for 8 button control and LED indicator devices
7. Power Indicator
Blue LED indicates a present 12V power supply
8. Intensity control
LED Brightness control knob
1
2
3
4
4
5
6
7
8

OPERATING MANUAL
Introduction
Thank you for purchasing the CS-RGB8g ChoiBox.
CS-RGB8g is designed as a quick interface and is a simple field installation unit that can be used
with the ClockAudio electronic captive touch switch series.
- Compatible with the ClockAudio TS001, TS003, TS005, and SWP2
- Supports the MRA HUSHBUTTON
- Can interface with the Shure microphones
- Two test buttons for easier field function tests without an external control frame
- Up to 8 LED switches can be connected to one CS-RGB8g
- Daisy chain multiple CS-RGB8g for a larger quantity of LED switches
- Can be interfaced with most control frames and DSPs (Crestron, AMX, Biamp, QSC,
ClearOne, BBS, etc.)
- Connects with dry contact or logic level interface devices
The CS-RGB8g is a simple interface box for Microphone mute buttons and Multi color LED
indicators
- Multi color LED support. ( 7 different color indication )
- Phone incoming call indication ( Slow blinking with selected color )
- Fire alarm indication ( Fast blinking with selected color )
- Adjustable blinking speed
- Adjustable LED brightness
The CS-RGB8g is fully compatible with all previous models:
- CSB8g
- CSB8gex
The CS-RGB8g is compatible with the following manufacture models:
- ClockAudio 1st and 2nd generation Dual or Multi color
- Shure MX series
- FSR T3 series
- MRA HUSH BUTTON ( require pin change )

Application Note:

Specification.
Dimensions
- 4.75” W x 3.33” L x 1.8” H
Weight
- 0.3lbs.
Connectors
- 8x RJ45
- 2.1mm power plug
- 5pin phonix connector
Power
- 12V 3A wall plug switching power supply
Thermal
- Operating temperature 0 ~ 40 ‘C
Input logic
- TTL Logic Level, H→Open, L→GND.
Output Logic
- Open collector. Sink 200mA max.
Technical support.
Please contact : su[email protected]
www.choibox.com
Rev 3.0

PIN OUT Information
RJ45
PIN 1 –Additional Switch Input (future)
PIN 2 –RED LED
PIN 3 - GND
PIN 4 - +12V
PIN 5 –Switch Logic Control
PIN 6 –Green LED
PIN 7 –Blue LED
PIN 8 –TTL Logic output
5pin Phonix connector I/O control port
Pin1 : Input GND (System Ground )
Pin2 : Input Remote ( Open/High = Inactive; Low = Active)
Pin3 : Input LED Input ( Default colors: Open/High = Red LED; GND/Low = Green LED )
Pin4 : Switch Out Open collector (Pin4 Logic level changes to LOW when any button is pressed)
Pin5 : Logic Input (Default color: GND/Low = Blue LED, solid or blinking based on Dip SW10)
Note: Input Voltage 0V ~ 2V is considered LOW, 2.1V ~ 12V or open is considered High
TEST Button
Test1: Press “REMOTE” →Same as when I/O Pin2 is LOW. RED LED will light up.
DIP SW 1,2,3 combination can change the LED color. RED is the default set.
Test2: Press “REMOTE” and “LED/LOGIC” →Same as when I/O Pin2,3 is LOW.
GREEN LED will light up.
DIP SW 4,5,6 combination can change LED color. GREEN is the default set.
Test3: Press ”LED/LOGIC” →Same as when I/O Pin5 is LOW. BLUE LED will blink.
DIP SW 7,8,9 combination can change LED color. Blue is the default set.
Period knob can change blinking speed.
DIP SW 10 mode switch position: UP = blinking; DOWN = solid